Ltcs20020s Parts

This fan grille assembly covers and protects the appliance's circulation/cooling fan while guiding airflow through the compartment. Replacing a cracked or missing grille helps restore proper air movement and can reduce noise from contact or vibration.

• Protects fan blades from debris and accidental contact
• Directs airflow for efficient cooling/circulation
• Helps stabilize adjacent ducting/shrouds to reduce vibration
• Typical failure signs include rattling or scraping noises, weak airflow, temperature inconsistencies, or visible broken tabs/cracks

• Disconnect power before servicing; wear cut-resistant gloves
• Access the fan area and remove any shelves/panels as needed
• Remove mounting screws/clips, note orientation, and transfer any reusable seals or clips from the old grille
• Install the new grille and ensure the fan spins freely without contact before reassembly and restoring power

This small control knob mounts on the shutter mechanism so you can open, close, or fine-tune the setting with a simple turn. Replace a cracked, loose, or missing knob to restore smooth adjustment and a clean, finished look.

• Attaches to the shutter/damper shaft to select positions
• Provides a secure grip for easy, precise adjustment
• Common failure signs: cracked or stripped hub, loose fit, missing knob
• May cause difficulty adjusting the shutter or settings to slip

• Disconnect power if removing any covers or panels near electrical components
• Pull the old knob straight off; rock gently if stuck to avoid damaging the shaft
• Align the keyed/D-flat opening with the shaft and press firmly until fully seated
• The shutter moves smoothly through its full range

The Door Basket is an OEM accessory specifically designed for LG refrigerator doors containing vegetable drawers. This hanging basket provides auxiliary storage directly above crisper bins.

Causes of a bad door basket can include wear and tear over time compromising the mesh material, or damage from overloading reducing structural integrity.  

Symptoms of a bad door basket include:

• Holes or tears reducing usable capacity   
• Detached fasteners slipping off mounting brackets
• Warped contours no longer remain properly installed
• Insecure attachment inhibiting safe door openings  

Replace yours today with this genuine OEM LG basket to maximize organizational convenience. Sturdy brackets produce a snug, stable fit. Compatible with Samsung, GE, and Frigidaire refrigerators featuring dual-drawer doors, this upgrade complements any modern kitchen setup. Reliable performance preserves aesthetic appeal.

The PCB Assembly, Display is an OEM part for LG refrigerators. It is responsible for controlling the refrigerator's display functions and interface. This board monitors temperature and cycle settings and regulates the input/output of operational data to the control panel. It assists users by displaying temperatures, selections, and error codes.

Causes of a bad display board can include liquid damage, thermal stresses from opening/closing doors over time, and short circuits due to manufacturing defects.

Symptoms of a bad PCB assembly include:

• Faulty or unreadable control panel display
• Buttons not responding properly  
• Random error codes appearing
• Glitches in temperature or function display

This genuine LG replacement ensures dependable control panel performance. It preserves your investment and restores full refrigerator operations. This part is also compatible with Sears/Kenmore models utilizing LG components and controls.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This customized screw secures specific appliance components to maintain proper fit and prevent parts from loosening during normal use. Use it when replacing a missing or damaged fastener to restore secure assembly and reduce vibration. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Keeps parts aligned to prevent rattling or movement during operation
• Replaces stripped, missing, or damaged screws that cause loose assemblies
• Helps maintain electrical and mechanical connections by holding parts in place

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep removed hardware organized for reassembly; replace any additional damaged fasteners

This customized screw is the manufacturer-specified fastener used to secure appliance components and panels at their mounting points. Replace a missing, stripped, or corroded original to restore a tight fit, proper alignment, and help eliminate vibration or rattling.

• Secures brackets, covers, and panels to the chassis at designated mounting points
• Maintains alignment and stability of the assembly during operation
• Helps address loose or rattling components caused by a missing or damaged fastener
• Direct replacement for the original fastener used in the specified location

• Disconnect power; shut off water before servicing
• Match head/length to the original; transfer any original clips or washers if used
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten until snug—do not overtighten into plastic or thin sheet metal

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

The Power Cord Assembly is an OEM replacement part for LG refrigerators. It includes the electrical cord and strain relief that links the refrigerator to an external power source.  

This power cord assembly safely delivers electricity from the wall outlet to the internal compressor and fan modules. It facilitates proper cooling functions through this transmission of alternating current.

Symptoms of a bad power cord can include:

• Abnormal sounds such as humming or buzzing from within 
• Tripped circuit breakers interfering with operations
• Indicators of cord damage like frays or exposed wiring
• Inconsistencies in interior temperature maintenance

Causes may involve normal wear over extended use, physical stress, or accidental damage to the cord insulation.  

Replacing the power cord assembly with this genuine LG OEM part restores a reliable electrical pathway. It ensures a continued power supply to keep foods fresh and frozen.

The Lower Hinge Assembly is an OEM part for LG refrigerators. This lower hinge safely and smoothly supports the weight of the refrigerator door.

Causes of a bad lower hinge can include loose or worn parts from years of use, damage from overloading doors with heavy items, or failure due to impact or bending stresses.  

Symptoms of a bad lower hinge include:

• Doors sagging or dropping over time
• Noisy squeaks or grinding sounds coming from hinges
• Difficulty opening and closing doors smoothly  
• Doors unable to stay open at various angles

Replace yours today with this genuine OEM LG assembly before further issues develop. This replacement part is compatible with Frigidaire, Samsung, and Kenmore models for a factory fit and function.

This replacement shelf glass restores a flat, sturdy surface inside your refrigerator for safe, organized food storage. Replace cracked, missing, or unstable glass to help contain spills and return your shelf to full strength.

• Provides a level, load-bearing surface for food containers in the compartment
• Helps contain leaks and spills so messes don't spread below
• Replace when glass is cracked, chipped, shattered, bowed, or missing
• Restores lost storage space and improves shelf stability

• If handling broken glass, unplug the refrigerator and wear cut-resistant gloves and eye protection.
• Remove items from the shelf, slide out the shelf/assembly, and carefully lift out the old glass.
• Clean any debris from the frame or supports. Set the new glass in place, ensuring it seats fully and is secure before reinstalling.

This door gasket assembly seals the refrigerator door to the cabinet to stop air and moisture leaks. A tight, even seal helps maintain interior temperature, reduce frost and condensation, and support efficient, reliable cooling performance.

• Creates a continuous perimeter seal between the door and cabinet
• Helps stabilize interior temperature and humidity
• Reduces frost, sweating, and condensation around the door opening
• Replaces gaskets that are torn, warped, brittle, or permanently flattened

• Disconnect power before servicing and clear items from the door.
• Let the new gasket warm to room temperature; relax bends with warm water or low heat if needed. Do not overheat.
• Press the gasket lip fully into the door channel, working evenly around all sides and corners.
• Close the door and verify uniform contact all around; reseat the gasket as needed for an even seal.

This vegetable tray stores and organizes produce in the refrigerator's fresh-food compartment. Replacing a cracked or missing bin restores usable space and smooth sliding access so fruits and vegetables stay contained and easy to reach.

• Holds fruits and vegetables in the crisper area
• Slides in/out on existing drawer rails for convenient access
• Helps keep items separated and contain minor spills
• Common symptoms: cracked or broken bin, missing tabs, drawer won't slide smoothly or stay seated

• Remove contents and slide the old drawer straight out
• Align the new drawer with the existing rails and push in until fully seated
• Handle nearby glass shelves carefully to prevent chips or breakage
• Disconnect power before working inside