Ltcs24223s/04 Parts

This harness assembly routes power and signals between appliance components to restore electrical connections and normal operation. It replaces damaged or frayed wiring to stop intermittent power, control failures, or no-start conditions. What it does:

• Reconnects power and control circuits between major components
• Replaces damaged, burned, or frayed wires and connectors that cause intermittent or lost function
• Restores reliable signal paths to controls, sensors, and motors
• Helps resolve symptoms like sporadic operation, failure to start, or component non-response

• Disconnect power to the appliance before accessing electrical components.
• Match connectors and wire routing to the original harness during installation to avoid pin miswiring.
• Inspect connector pins and mating terminals for damage; replace the harness if pins are bent or corroded.

This is a genuine replacement screw used to secure appliance panels and components. It restores proper fastening so panels and assemblies stay aligned and operate safely. What it does:

• Fastens panels, brackets, and small assemblies to maintain structural integrity
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop vibration-related noise when used in its original mounting locations
• Matches the OEM fit to ensure proper alignment and clearance

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Disconnect power to the appliance before working on electrical components
• Replace all matching fasteners for even fit

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling or loose parts. Simple, direct replacement when a worn or missing screw causes loose panels or intermittent contact. What it does:

• Fastens panels, brackets, or small components to maintain proper alignment and reduce vibration
• Prevents loose trim, covers, or assemblies that can cause noise or improper sealing
• Replaces missing, stripped, or corroded screws that interfere with reliable operation
• Works wherever the OEM screw specification is required for secure mounting

• Use the matching screw hole and tighten until snug; avoid over-torquing to prevent stripping
• Disconnect power to the appliance if accessing electrical or moving parts near the work area
• If multiple screws are missing or panels are damaged, replace all fasteners for even support

The PCB Assembly, Main is an OEM part specifically designed for LG refrigerator units. It serves as the central processing control, regulating cooling functions and temperature levels across storage compartments.  

Causes of a bad PCB Assembly, Main include natural wear of circuitry from years of continuous usage. Water damage poses risks of short-circuiting sensitive pathways over time as well. 

Symptoms incorporate:

• Inconsistent cooling making temperatures fluctuate erratically  
• Unusual humming or knocking noises within refrigerator walls
• Failure to achieve or maintain temperature set points as designed

Replacing with this genuine LG board revives the full intended operation. Circulation of conditioned air throughout is optimized once more with upgraded components. This replacement ensures refrigeration performs reliably to keep foods fresher and longer. It also fits Sears/Kenmore models.

The Lower Hinge Assembly is an OEM part for LG refrigerators. This lower hinge safely and smoothly supports the weight of the refrigerator door.

Causes of a bad lower hinge can include loose or worn parts from years of use, damage from overloading doors with heavy items, or failure due to impact or bending stresses.  

Symptoms of a bad lower hinge include:

• Doors sagging or dropping over time
• Noisy squeaks or grinding sounds coming from hinges
• Difficulty opening and closing doors smoothly  
• Doors unable to stay open at various angles

Replace yours today with this genuine OEM LG assembly before further issues develop. This replacement part is compatible with Frigidaire, Samsung, and Kenmore models for a factory fit and function.

This cover support bracket secures an appliance cover or panel, restoring proper alignment and stability. Replacing a damaged support helps eliminate rattles and gaps so the cover seats correctly and stays in place.

• Provides structural support for the associated cover/panel
• Keeps the cover aligned and firmly seated against the cabinet
• Replaces a cracked, stripped, or missing support
• Symptoms include a loose or sagging cover, vibration/rattling noises, or covers that won't stay attached

• Disconnect power before servicing; allow any hot surfaces to cool and wear cut-resistant gloves
• Remove the cover/panel to access the support and retain all mounting hardware
• Install the new support, transferring screws or clips as needed
• Reinstall the cover and verify proper fit before restoring power

This guide tube is a small routing sleeve that supports and protects a rod, shaft, cable, or line inside your appliance. It keeps the path straight to reduce friction, noise, and premature wear.

• Guides and supports a rod/shaft/cable/tube through the chassis
• Maintains alignment for smooth movement or flow
• Helps prevent chafing, kinks, and vibration-related damage
• Typical failure signs: scraping or rattling noises, binding/misalignment, or visible cracks/deformation

• Disconnect power; turn off water or gas before servicing
• Refer to your model's parts diagram for routing and mounting points
• Reuse original screws/clips unless damaged
• Route exactly like the original; avoid pinches/kinks and verify clearances before restoring power

This control case assembly is the replacement outer housing that holds and protects the appliance control board and user interface, restoring a secure fit and proper button/panel alignment for safe operation. What it does:

• Houses and protects the control board and associated electronics from dust, moisture, and accidental contact
• Keeps control panel buttons and switches properly aligned for reliable user input
• Prevents loose or rattling control components that can cause intermittent operation or noise
• Supports the front panel and display mounting for normal appearance and functionality

• Disconnect power to the appliance before starting any repair to avoid electric shock.
• Handle the control board and connectors carefully; avoid touching circuit traces or components.
• Basic hand tools are typically required to remove the panel and transfer the control board into the new housing.
• If the control board is damaged or shows corrosion, this part replaces only the housing unless otherwise specified.

The Heater Sheath is an OEM part for Frigidaire refrigerators. It contains a heating coil that provides regulated temperatures within the fridge. The sheath helps direct airflow while protecting internal insulation. 

Causes of a faulty heater sheath can include normal wear from years of cooling cycles. Mineral deposits accumulating on the coil could disrupt temperature regulation. Physical damage puts it at risk for air and moisture leakage issues.

Symptoms of a failed heater sheath are:

• Fluctuating interior temperatures and issues maintaining the temperature setting
• Frost or ice buildup within the fridge compartments  
• Increased energy usage without adequate chilling performance

This OEM replacement part is compatible with brands including Electrolux, Gibson, Kelvinator, and Kenmore. 

This overload protector is a motor thermal cut-off that helps prevent motor overheating by interrupting power when temperatures get too high. It restores normal operation after the motor cools, helping protect the motor from heat damage. What it does:

• Senses excess motor temperature and interrupts power to prevent overheating
• Commonly used when a washer or motor hums, won't spin, or stops mid-cycle
• Protects the motor and associated components from heat-related failure
• Resets or is replaced after a thermal fault clears, depending on design

• Disconnect power before accessing the motor or electrical components
• Handle and mount the protector per OEM orientation to ensure proper thermal contact
• Inspect motor and wiring for underlying faults before replacing

This door stopper is the replacement part that cushions and limits a dryer or washer door's movement to prevent slamming and reduce wear on the hinge. It restores proper door motion and helps keep the door aligned during use. What it does:

• Absorbs impact and limits door travel to prevent slamming and hinge damage
• Helps keep the door aligned so it closes and latches properly
• Reduces vibration and noise caused by uncontrolled door movement
• Commonly replaced when the door bangs, hangs unevenly, or the hinge feels loose

• Disconnect power (and water if working on a washer) before beginning any repair
• Access the stopper by removing the top or front panel per your model's service instructions
• Inspect associated hinge and mounting hardware; replace if damaged