Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures hose connections to prevent leaks in your washer. Replace if you notice dripping at hose fittings or loose connections. Verify fit with your model.
Took off cover, installed new parts. Read more
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more
Fix a burnt or melted lid switch connector causing your washer to be completely dead. This terminal receptacle restores power to the lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Rear leveling foot assembly that supports the back of your laundry center. Replace if cracked, broken, worn, or missing to restore stability.
Ordered the broken and missing part Read more
Heat-resistant fiberglass gasket seals your oven door perimeter to maintain consistent temperatures. Replace when worn, frayed, or flattened to restore efficiency. Verify fit by model number.
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Fix a washer agitator that won't turn or spins weakly with this lower agitator base. Restores proper wash action when worn, cracked, or stripped.
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Leaking washer or water pooling near your laundry center? A cracked inlet hose is often the cause. This hose routes water from the valve to the drum.
Replaced with new one. Read more
Fix front panel water leaks with a new internal water inlet hose. Routes water from valve to fill system. Stops leaks from cracked or split hoses.
Removed front panel,lift and tilt out bottom.3/4" hose from rear to front valve had split.Cut end w/part no.# on it and ordered from site.Part came in 2 days.Removed clamps with pliers,lubed ends and slid on.Works fine. Read more
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
Seals the siphon break fitting to prevent leaks and maintain proper drainage. Replace if cracked, loose, or missing. Verify fit with your model number.
Replaced parts Read more
White timer knob for washer dryer combo units. Replaces cracked, stripped, or missing original knobs. Attaches to timer shaft for cycle selection.
Replaced knob Read more
Anchors screws in thin metal or plastic panels to secure trim, covers, and consoles. Replace worn, cracked, or missing grommets that no longer hold tight.
10-16 x 5/8 inch mounting screw for washers and dryers. Replaces rusty, corroded, or broken screws that secure console panels and internal components.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more