M-Ffc13k2cw1 Parts

This clamp secures flexible hoses to fittings to maintain a tight seal and prevent leaks. Use it to replace a worn or loose clamp to stop water or air seepage and restore proper hose attachment. What it does:

• Holds a washer, dryer, or appliance hose firmly to a barb or fitting to prevent slipping
• Helps maintain a watertight or airtight connection to reduce leaks and drips
• Replaces corroded, cracked, or stretched clamps that no longer grip reliably
• Supports normal appliance operation by keeping fluid/air flow contained

• One clamp

• Inspect the hose and fitting; replace the hose if damaged before installing the clamp
• Position clamp over the hose barb and tighten evenly; avoid over-tightening that can cut the hose
• Disconnect power and water supply before servicing any appliance components

This replacement access cover restores the appliance's exterior finish and helps protect internal components from dirt and accidental contact. Simple, direct-fit design for restoring safety and appearance after damage or removal. What it does

• Shields internal components and wiring from dust, debris, and accidental contact.
• Helps stop rattles and vibrations caused by a missing or loose cover.
• Restores the appliance's finished look after repair or maintenance.
• Provides a mounting surface for screws and attaches flush to the cabinet.

• Disconnect power (and water, if applicable) before starting any work.
• Remove any fasteners or trim pieces holding the old cover in place; lift cover straight out to avoid pinching wires.
• Align new cover and secure with the original screws; do not overtighten to avoid cracking the plastic.
• If any clips or mounting tabs are damaged, replace them before reinstallation to ensure a secure fit.

This bale strap is a direct-replacement part that helps secure the dryer's latch/bale assembly so the door closes and stays closed during operation. Replacing a worn or broken strap restores reliable door engagement and safer drying cycles. What it does:

• Anchors the dryer door's latch/bale so the door remains properly closed during operation
• Prevents intermittent door opening that can stop cycles or cause heat loss
• Replaces a stretched, torn, or broken strap that no longer holds the latch securely
• Works with the door/latch mechanism to maintain safe operation during drying

• One bale strap

• Disconnect power before beginning any repair to avoid electrical shock
• Verify strap routing and attachment points match the original before reinstalling
• Basic hand tools are typically required; avoid forcing plastic clips to prevent breakage

Size: 1/4 lb.

Size: 1/4 inch.

This rubber condenser grommet cushions and secures the condenser assembly to reduce vibration and noise, helping the refrigerator run quieter and preventing wear where the condenser mounts to the cabinet. What it does:

• Cushions condenser mounting points to reduce rattling and vibration
• Helps prevent metal-on-metal wear between condenser and chassis
• Keeps the condenser properly seated for reliable airflow
• Reduces noise caused by loose or worn condenser mounts

• Disconnect power to the appliance before beginning any service
• Access the condenser area per your model's service instructions
• Remove the old grommet and press the replacement into the mounting hole until seated
• Do not use solvents or adhesives unless specified by the manufacturer; wear gloves to protect hands

Color: White

This replacement name plate restores the appliance's exterior appearance by replacing a damaged, faded, or missing logo/trim plate. It provides a clean, factory-look finish so the model retains its original styling. What it does:

• Replaces a worn, cracked, or missing name plate to restore the appliance's exterior appearance
• Covers the same mounting area as the original so logo/branding and trim look correct
• Helps maintain resale value and overall cosmetic condition
• Fits and aligns with existing fasteners or attachment points for an OEM fit

• One replacement name plate

• Disconnect power or gas supply to the appliance before beginning work and follow all safety precautions
• Remove the old name plate carefully to avoid scratching the surrounding surface or damaging fasteners
• Install the new plate using the original screws, clips, or adhesive as applicable; do not force parts into place

This drive coupler connects the washer motor to the transmission so the agitator or drum turns smoothly. It's a direct-replacement part that restores drive engagement when the original coupler is worn or damaged. What it does

• Transfers motor rotation to the transmission/agitator so the tub agitates or spins.
• Commonly replaced when the washer won't agitate, spin, or makes grinding or clunking noises.
• Resists normal wear from torque and repeated use; failure causes slipping or loss of drive.
• Helps prevent further damage to the motor or transmission when replaced at first signs of wear.

• One drive coupler

• Disconnect power and water supply before beginning any repairs.
• Access typically requires removing the cabinet or front panel; follow the manufacturer service manual.
• Inspect motor shaft and transmission input for damage when replacing the coupler.
• If transmission or motor splines are damaged, replace the damaged assembly rather than relying on a new coupler.