Maytag Cwe 4800 Parts

This cup fill is the molded water cup that directs water into the refrigerator ice maker so it forms full, even ice cubes. It replaces a cracked or clogged cup to restore normal ice maker fill performance. What it does:

• Channels the incoming water supply into the ice maker mold for consistent cube formation
• Helps prevent leaks or overflows caused by cracked, split, or misshapen cups
• Common fix when the ice maker fills slowly, unevenly, or not at all
• Works with compatible GE ice maker assemblies that use a molded fill cup

• One cup fill

• Disconnect power and shut off the water supply before starting work
• Remove the ice maker assembly or access panel per your model's service instructions
• Inspect surrounding seals and the inlet area; replace if cracked or damaged
• Reconnect water and power, then run a few cycles to check for leaks

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

This oven temperature probe senses the cooking cavity temperature so the range control can regulate heat for accurate baking and roasting. It replaces a failed or intermittent sensor to restore correct temperature feedback. What it does:

• Measures oven temperature and sends the signal to the control board for proper heating control
• Helps correct symptoms such as oven not reaching set temperature, inconsistent baking, or temperature error codes
• Provides the oven control with the feedback needed for timed cooking and self-clean cycles
• Replaces a damaged or open/shorted probe that causes incorrect temperature readings

• One temperature probe

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Handle the sensor and connector gently to avoid damage; route and secure wiring as originally installed
• Reconnect wiring fully and verify secure connection; test oven function and temperature accuracy after installation

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This replacement freezer ice bucket stores and dispenses ice made by your refrigerator's icemaker, keeping cubes contained and easy to access. It restores proper ice collection and makes removing or transferring ice quick and tidy. What it does:

• Holds and stores ice produced by the icemaker so cubes don't fall into the freezer compartment
• Guides ice from the icemaker into the bin to keep production flowing
• Prevents loose ice and reduces mess when removing ice for use
• Replaces cracked, warped, or missing ice bins that no longer contain ice properly

• One ice bucket

• Remove power to the refrigerator or switch icemaker to the OFF position before working near the icemaker
• Slide old bin out and lift the replacement into the same tracks or ledges; no special tools typically required
• Handle carefully to avoid cracking plastic; ensure bin seats fully so ice drops correctly from the icemaker
• If ice continues to spill or production stops after installation, check icemaker alignment and operation per the refrigerator service instructions

The Dispenser Assembly is an OEM replacement part for GE refrigerators. This actuator is responsible for controlling the functions of the refrigerator's dispenser, allowing you to dispense water or ice.

A bad dispenser actuator assembly can occur due to wear and tear, damage, or component failure over time. If you notice symptoms such as the dispenser not responding to your input, loose or wobbly movement of the actuator, or the dispenser not dispensing water or ice properly, it may indicate a need to replace the actuator assembly.

Symptoms of a bad dispenser actuator assembly include:

• Unresponsive dispenser
• Loose or wobbly actuator movement
• Improper dispensing of water or ice

Restore your refrigerator's dispenser by replacing the faulty dispenser actuator assembly with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This lower basket slide is the replacement rail that supports and guides the dishwasher's lower rack for smooth in-and-out movement. It restores stable, aligned operation so the rack rolls without binding or sagging. What it does:

• Supports the lower dish rack and keeps it aligned on the track
• Guides smooth sliding motion to prevent sticking or uneven travel
• Replaces worn or bent slides that allow the rack to sag or come off track
• Helps eliminate grinding, catching, or noisy rack movement

• Remove power to the appliance before any service for safety.
• Inspect rack rollers and adjacent slide hardware; replace any damaged components.
• Simple hand tools are usually all that's needed; handle parts gently to avoid bending.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

This element holder assembly secures an oven/range heating element and keeps it positioned for even heat delivery. It restores proper element alignment to reduce arcing and prevent rubbing or uneven baking. What it does:

• Secures the bake or broil heating element to the range/oven housing
• Keeps the element properly spaced for consistent heating performance
• Helps stop element movement, rubbing, or intermittent contact that can cause arcing
• Commonly replaced when the element is loose, misaligned, or makes noise during operation

• Disconnect power to the appliance before beginning any repair
• Handle heating elements carefully—sharp edges and fragile terminals can be damaged
• Verify element alignment and secure mounting hardware; replace only as needed
• If you see damaged element terminals or insulation, replace the element

This right-hand top hinge assembly secures and supports the refrigerator door at the cabinet top, restoring proper door alignment and smooth opening. It's a direct-fit replacement when the upper hinge is cracked, bent, or worn. What it does:

• Supports the upper corner of the door and maintains correct door alignment
• Helps the door open and close smoothly and stay level
• Prevents door sagging that can cause gaps, rubbing, or poor sealing
• Replaces damaged, bent, or broken top hinge hardware that can cause noisy operation

• Disconnect power to the appliance before starting and remove any items from the door
• Support or remove the door per manufacturer instructions before loosening hinge fasteners
• Use proper hand tools and tighten fasteners securely; check door alignment and gasket seal after installation

The Evaporator Cover and Fan is an OEM replacement part for GE refrigerators responsible for maintaining proper airflow and temperature regulation within the refrigerator's freezer compartment. The fan helps distribute the cold air while the cover protects the evaporator coils from any damage or obstruction.

A bad evaporator cover and fan can occur due to wear and tear, damage, or component failure over time. If you notice symptoms such as inconsistent cooling, excessive frost or ice buildup, or unusual noises coming from the freezer, it may indicate a need to replace the evaporator cover and fan.

Symptoms of a bad evaporator cover and fan include:

• Inconsistent cooling
• Excessive frost or ice buildup
• Unusual noises coming from the freezer

Restore your refrigerator by replacing the faulty evaporator cover and fan with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

The Lower Cabinet Harness is an OEM replacement part for GE refrigerators responsible for providing electrical connections between various components within the lower cabinet of the refrigerator.

A bad lower cabinet harness can occur due to wear and tear over time or damage caused by mishandling or accidents. If you notice symptoms such as intermittent or complete loss of power to components within the lower cabinet, flickering lights, or malfunctioning controls, it may indicate a need to replace the wiring harness.

Symptoms of a bad lower cabinet harness include:

• Intermittent or complete loss of power to components within the lower cabinet
• Flickering lights or erratic behavior
• Malfunctioning controls or display

Restore your refrigerator by replacing the faulty lower cabinet harness with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This LED light board assembly provides the replacement LED module that illuminates the control/display area. Restores visibility of panel indicators and display lighting for proper operation and ease of use. What it does:

• Replaces the LED light module that backlights the control/display area and status indicators.
• Restores faded or non-lit control panel lighting that makes buttons and icons hard to see.
• Can resolve intermittent or no-light symptoms caused by a failed LED board.
• Works with the original housing and connectors for a direct-fit replacement.

• One LED light board assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock.
• Handle the board by edges; avoid touching LED lenses or circuitry to prevent damage.
• Verify connector orientation and seating; secure mounting screws to prevent rattle.