Maytag De210 Parts

A replacement cycling thermostat that helps regulate dryer temperature and prevent overheating by cycling the heater on and off as needed. Restores temperature control for safer, more consistent drying. What it does

• Opens and closes to cycle the heating element, maintaining proper operating temperature.
• Helps prevent excessive heat build-up that can cause clothes damage or dryer shutdowns.
• Common fix for dryers that run too hot, have uneven drying, or won't maintain heat.
• Works with the dryer's existing temperature control system to stabilize cycles.

• One cycling thermostat

• Disconnect power before accessing or replacing the thermostat to avoid shock.
• This part mounts inside the dryer cabinet near the heating assembly.
• Handle the thermostat carefully and reconnect wires to the correct terminals.
• Test the dryer on a short cycle after install and monitor temperature; if symptoms persist, check other heating components.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

Specs: 7/32 INCH

High limit thermostat, Canadian models only.

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.

• Secures panels, brackets, and internal components to the cabinet or frame
• Helps prevent vibration, rattling, and misalignment from loose hardware
• Replaces a missing, rusted, or stripped original screw
• Matches the original fastener style for proper fit in specified locations

• Disconnect power; shut off gas and water supplies before servicing
• Use the correct screwdriver or nut driver and match length/thread to the original
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic or thin metal

A single replacement screw used to secure panels and components on compatible Whirlpool appliances. This genuine-style fastener restores proper fit and keeps parts aligned for safe, reliable operation. What it does

• Secures panels, brackets, or small components to the appliance frame
• Restores proper alignment for doors, control panels, or internal assemblies
• Helps eliminate rattles, loose parts, and poor fits caused by missing or damaged screws
• Simple, direct replacement when the original screw is lost or stripped

• One replacement screw

• Use the matching screwdriver or bit and tighten only until snug; avoid over-torquing which can strip threads or crack plastic
• Replace with the same size and thread form; compare to the original before installing
• Disconnect power to the appliance before accessing internal components to reduce shock risk

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This terminal block provides the electrical connection point between the washer's power cord and the appliance wiring, restoring a secure, stable supply for safe operation. It replaces a damaged or corroded connection assembly. What it does

• Secures and insulates power cord wires where they enter the washer to prevent loose connections and arcing
• Restores reliable incoming power when a burned, loose, or broken terminal causes intermittent power or no power
• Helps prevent electrical resistance and heat buildup at the cord connection
• Matches OEM mounting and terminal layout for a direct replacement

• One terminal block assembly as shown

• Disconnect the washer from power before servicing to avoid shock or injury
• Inspect wire colors and terminal positions, then transfer wires to the same terminals on the replacement part
• Typical installation requires basic hand tools (screwdriver, nut driver); some models may need partial cabinet access
• If you see melted insulation or other wiring damage, replace affected wiring.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

Ceramic