Maytag Lse7806gge Parts

Export motor.

A snap-style hose clamp that secures flexible appliance hoses to fittings to help maintain a leak-free connection. Simple, durable replacement for a lost or worn hose clip to keep hoses seated and stable. What it does

• Secures a flexible hose to a nipple or barb to help prevent accidental disconnection
• Helps maintain a tight connection that reduces risk of leaks at the hose joint
• Commonly used on drain, fill, or internal circulation hoses where a small snap clamp is required
• Small, low-profile design fits in tight spaces and resists shifting under normal use

• One snap-style hose clamp

• Disconnect power and shut off water supply before beginning any repair
• Access may require removing panels or disassembling interior components depending on appliance
• Pry open or compress the clip as needed with pliers to remove and reinstall; ensure hose is fully seated on the fitting before securing
• Inspect the hose and fitting for damage; replace hose if cracked or degraded

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This upper injector directs incoming water cleanly into the washer tub during fill and rinse. Replacing a cracked or clogged injector restores proper water delivery, helps prevent splash-back, and supports consistent wash performance.

• Channels inlet water into the tub from the upper injection point
• Helps prevent splash-back and backflow at the tub ring area
• Promotes even water spray for detergent/softener flushing as designed
• Common failure symptoms: water dripping or spraying from the fill area, leaks down the cabinet, slow/erratic fill, or visible cracking/mineral buildup on the injector

• Disconnect power and turn off both hot and cold water supplies before servicing
• Access the injector at the top/tub ring area; remove top or cabinet panels as required per model
• Transfer and secure the fill hose and clamps; ensure a fully seated connection
• Restore water and power, run a fill test, and check all connections for leaks

This agitator spring maintains the spring tension inside the washer's agitator assembly so the wash action engages reliably. When fatigued or missing, the agitator can slip, feel loose, or make clicking/ratcheting noises during the cycle.

• Provides spring tension within the agitator assembly
• Helps keep agitator components properly engaged for consistent wash action
• Symptom: upper agitator/auger slips or fails to advance
• Symptom: weak or intermittent agitation
• Symptom: clicking/ratcheting noises or a loose-feeling agitator

• Disconnect power and turn off water before servicing
• Remove the agitator cap and bolt/retainer to access internal components
• Note the order and orientation of parts; seat the new spring correctly before reassembly
• Snug the agitator bolt and reinstall caps; run a test cycle to ensure proper agitation

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

• Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
• Restores a secure grip and pointer for accurate time selection
• Commonly used to fix loose, cracked, stripped, or missing timer knobs
• Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

• Disconnect power to the appliance before starting any repair
• Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
• If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

Spesc: #12 pozi - drive

This Torx-head screw set replaces worn, stripped or missing Torx fasteners used throughout the appliance to keep panels and components securely fastened. Restoring proper fasteners reduces vibration and prevents loose parts. What it does:

• Secures control panels, trim pieces or internal components that use Torx-head screws
• Replaces damaged or corroded Torx screws that can cause rattling or misalignment
• Helps restore proper fit and finish after repairs or disassembly
• Uses a Torx drive for a more secure torque transfer than standard Phillips heads

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size Torx driver to avoid stripping the screw head
• Tighten screws snugly but avoid over-torquing to prevent thread or part damage
• Keep removed screws organized and compare to the new set before installation

This hex-head screw secures the bearing insert in place, maintaining correct alignment and stable operation. Replacing a damaged or missing screw restores secure bearing retention and reduces noise or wobble. What it does:

• Holds the bearing insert assembly firmly to prevent movement and misalignment
• Helps stop excessive vibration, noise, or drum wobble caused by a loose bearing insert
• Maintains correct spacing so the bearing and shaft rotate smoothly
• Replaces stripped, rusted, or missing fastening hardware for reliable operation

• Unplug the appliance or disconnect power before beginning any repair
• Use the proper hex driver and size to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can deform the insert or housing
• Inspect the bearing insert and surrounding parts; replace any damaged components for a lasting repair

This replacement nut is a basic fastener used to secure components and assemblies on compatible Whirlpool appliances, restoring a tight connection and preventing parts from loosening during use. What it does

• Secures panels, brackets, or components to a stud or bolt to keep assemblies stable
• Prevents rattling, vibration, or movement caused by a loose or missing nut
• Replaces a stripped, corroded, or lost nut to restore proper mechanical connection
• Works with the corresponding bolt or stud as part of the appliance's fastening system

• Disconnect power and water to the appliance and ensure it is stable before starting work
• Thread the nut on by hand first to avoid cross-threading, then tighten with the appropriate sized wrench or socket
• Do not overtighten — torque to the appliance manufacturer's specification when available
• Replace damaged studs or mating hardware if threads are worn or damaged

This exhaust vent extension restores proper exhaust airflow by lengthening or adapting the appliance exhaust outlet to the vent duct. It helps maintain safe ventilation and reduces backpressure that can cause poor performance or odors. What it does:

• Extends or adapts the appliance exhaust outlet to reach the home vent duct
• Directs exhaust airflow to reduce backflow and help prevent overheating
• Helps resolve symptoms like weak venting, lingering odors, or unusual appliance cycling
• Provides a stable connection point for the exhaust duct to improve sealing and airflow

• Turn off and disconnect power (and gas if applicable) to the appliance before installing.
• Use proper fasteners and high-temperature-rated duct tape or clamps as recommended by the appliance manufacturer.