Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fixes intermittent operation or no power issues caused by melted or cracked connector housing. Secures terminal connections in washer wiring harness.
10-16 x 5/8 inch mounting screw for washers and dryers. Replaces rusty, corroded, or broken screws that secure console panels and internal components.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more
Fixes grinding noise or basket won't spin issues by disengaging the brake during spin cycles. Restores smooth operation when cam wears out or breaks.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Fix a washer that won't spin or makes loud noises during the spin cycle. This brake and clutch assembly restores proper agitation and spinning action.
Replaced clutch disc Read more
Secures wiring harness to washer top panel. Replace this clip if original is broken, missing, or no longer holding wires firmly in place during operation.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
Fix a washer that won't advance cycles or gets stuck between rinse and spin. This cycle selector switch controls washing cycle progression.
Fix a washer that won't fill or agitate properly with this 3-circuit pressure switch connector. Simple DIY repair in under 30 minutes with basic tools.
Watched on line Video. Only problem was in disconnecting wire "bus" connector from switch. I was unable to remove connector without damaging it. I "jumped" connector to prove switch was faulty. This also allowed my wife to continue to do laundry while part arrived. I ordered a 3 circuit connector, but this was not the correct part. I ended up removing 3 wires from old broken connector and attaching them to new switch without a connector. Electrical tape did the trick. Not perfect... Read more
Spin tube assembly with drive spacer, bearing, and shaft seals. Replace if washer leaks from bottom or basket doesn't spin properly. Verify fit.
It was fairly difficult, but I watched and followed the Appliance PartsPros video and was able to get it done using the parts I purchased from APP. The leak has stopped (but I'm still watching after 5 loads). Read more
Gasket sealer adhesive for dryers and laundry appliances. Bonds and seals gaskets during installation or repair. Replace when worn or missing.
Right-hand lid hinge for washer tops. Replaces worn, rusted, or broken hinges that cause lids to sag or not open smoothly. Direct fit replacement.
New parts easy fix Read more
Fix a washer that won't advance through cycles or skips rinse with a new timer. This control part manages cycle progression. DIY repair in minutes.
I replaced the timer. Once the part arrived, it took about two minutes to put on and start the washer. Read more
Hardware washer distributes load under fasteners to prevent loosening and reduce vibration. Replace when missing or damaged to restore secure fit.
Watched a video online, the project took about 20 minutes, went well, parts fit good, the video was very helpful in getting the wash machine up and running. Read more
Suspension skate plate mounts under the washer drum to support the tub assembly. Replace if cracked, broken, or warped. Includes suspension pads.
Washer won't spin or makes noise during spin? This clutch spring cap maintains proper tension in the drive assembly. Quick 5-minute DIY repair.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Fix a washer that won't switch water temperatures or cycles properly. This rotary switch controls temperature selection and cycle progression.