Mdc 5100 Aww Parts

This replacement power cord supplies mains power to an electric range or oven, restoring reliable power delivery so the appliance can heat and operate normally. Designed as a direct-fit electrical cord for compatible models. What it does:

• Delivers line and ground connections from the wall outlet to the appliance electrical terminal
• Replaces a damaged, frayed, or burnt cord that can cause intermittent power or no power to the range/oven
• Helps eliminate loose connections that produce arcing, overheating, or tripping breakers
• Provides a correct, durable power connection when the OEM cord has failed

• Disconnect power at the main breaker or fuse box before starting work
• Access the appliance terminal block (usually behind a rear access panel) and reattach wires to the correct terminals
• Use proper wire connectors and tighten terminal screws to the manufacturer's torque; secure strain relief per the appliance design

This brace connector is a small structural support that secures and stabilizes appliance components, helping maintain proper alignment and reduce vibration. It restores firm attachment where a worn or broken connector causes movement. What it does:

• Secures joining points between panels or assemblies to prevent looseness and rattling
• Restores proper alignment of connected parts so doors, panels, or controls operate smoothly
• Helps reduce vibration and noise caused by a failed or missing connector
• Works as the replacement structural fastener specified by the manufacturer

• Disconnect power (and water if applicable) before beginning any repair
• Basic hand tools (screwdriver, socket) typically required; inspect mounting hardware and replace if damaged
• Verify correct orientation and tightness during installation to avoid stressing adjacent parts

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Door latch assembly that secures the appliance door and enables the unit to detect a closed door so cycles can start. Replacing a damaged latch restores reliable door closure and proper operation. What it does:

• Secures the door and engages the door-switch/lock circuit so the appliance recognizes a closed door.
• Helps prevent leaks and ensures cycles start only when the door is properly latched.
• Common symptoms: door won't stay closed or latch, appliance won't start, intermittent locking or clicking noises.
• Replaces worn, cracked, or broken latch assemblies to restore normal door function.

• Disconnect power before servicing; for water-connected appliances also shut off the water supply.
• Remove the appropriate door panel or access cover per the service manual and keep original fasteners.
• Position the new latch, secure with the original screws without overtightening, then test door operation and a trial cycle before finishing reassembly.

This inner door plastic is the interior panel for the appliance door that supports latch and hinge hardware and helps maintain the door seal. Replacing a cracked or damaged inner panel restores proper door fit and function. What it does:

• Supports the door assembly and secures internal components; a damaged panel often causes a loose or rattling door.
• Provides mounting points for the latch and hinge hardware; symptoms include a door that won't latch or closes unevenly.
• Helps maintain the appliance seal and thermal integrity; symptoms can include noticeable air/heat leakage or reduced performance.
• Restores the interior appearance of the door when the original plastic is cracked, warped, or broken.

• Disconnect power to the appliance before beginning work and fully open the door; support the door to prevent it from dropping when fasteners are removed.
• Remove the required screws/fasteners and lift out the inner panel carefully; wear safety gloves and eye protection if glass is present.
• Check hinge and latch alignment during reassembly; replace any damaged fasteners and avoid overtightening screws which can crack the plastic.

This control board housing secures and protects the washer's electronic control board, keeping circuitry stable and shielded from moisture and debris for reliable operation. It fits into the console area and supports proper control panel alignment. What it does:

• Holds and protects the electronic control board inside the console from impact, dust and moisture.
• Keeps the control board properly positioned for reliable electrical connections.
• Helps prevent control panel wobble or misalignment that can cause button or dial issues.
• Commonly replaced when housing is cracked, broken mounting tabs fail, or board access is needed.

• 1 control board housing

• Disconnect power and water to the appliance before beginning any repair.
• Handle the control board and housing carefully to avoid damage to connectors or circuit components.
• Use appropriate tools to remove console components; replace damaged mounting tabs and secure all fasteners.
• Discharge any capacitors and follow the board manufacturer's ESD/safety recommendations.

This replacement rack track restores smooth, stable rack movement and keeps the oven rack aligned while sliding in and out. It helps prevent rack sagging, binding, or uneven travel so food and cookware stay level and secure. What it does

• Guides and supports the oven rack so it slides in and out smoothly.
• Prevents racks from sagging, tipping, or binding when pulled forward.
• Restores proper rack alignment to reduce scraping, catching, or loud banging.
• Works with standard oven/range racks that use a molded metal/plastic track system.

• High-level swap: remove the oven racks, unfasten the old track, and secure the replacement in the same mounting locations.
• Use appropriate hand tools and avoid forcing parts; aligning the track before tightening fasteners reduces binding.
• Disconnect power to the appliance or follow the manufacturer's safety guidance if servicing components near electrical connections.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

Color: Gray

A door latch assembly that secures the appliance door and allows the control to detect a closed, locked condition so cycles can start and run. Replaces a worn or broken latch to restore proper door closure and reliable cycle operation. What it does:

• Secures the door so the appliance can sense a closed/locked state and begin a cycle
• Prevents the door from opening mid-cycle for safe operation
• Commonly used when the door won't stay closed or won't register as closed
• Helps stop issues where the unit won't start or won't advance through a cycle due to a faulty latch

• Disconnect power (and water for washers) before beginning any repair
• Remove the cabinet or door panel per your model's service instructions to access the latch
• Test door operation and start a short cycle after installation to confirm correct function

This motor-pump is the dishwasher drain pump assembly that removes water from the tub so cycles can complete. Replacing a failed pump restores proper draining and helps prevent standing water and cycle errors. What it does:

• Spins the impeller to pump wastewater out of the dishwasher during drain cycles
• Stops leaks and prevents water from remaining in the tub when working correctly
• Commonly linked to symptoms such as no draining, water left in the tub, or a humming noise during drain
• Works as the integrated motor and pump — not a separate impeller-only part

• Disconnect power and shut off water supply before starting any repair
• Handle with care to avoid damaging the impeller, seals, or electrical connector
• May require removing access panels or the dishwasher kickplate; use appropriate tools