Medb0yw0 Parts

The Overlay is an OEM part for Whirlpool electric dryers. The decorative plastic covering fits over the dryer door opening and controls. 

The overlay plays a cosmetic role in protecting internal components and providing an attractive facade. It features a sleek surface that complements the surrounding kitchen appliances.

Symptoms of a bad overlay include:

• Cracks or peeling along high-stress areas  
• Loose or misaligned fitting over controls
• Stains or discoloration from cleaning chemicals

A bad overlay typically causes normal wear and tear over time from heat, impacts, or harsh cleaners. Proper care can extend its lifespan.

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This console control panel assembly houses the range's user controls and display, restoring a secure mounting surface and user interface for normal operation. It replaces a cracked, damaged or nonfunctional console to regain safe control access. What it does

• Provides the mounting surface and bezel for the cooktop/range control buttons, knobs, and display
• Restores proper alignment and protection for the control electronics and user interface
• Commonly replaced for cracked or broken panels, loose or missing button backing, or cosmetic damage
• Resolves issues with inaccessible controls or intermittent button response when damage is the cause

• One console control panel assembly

• Disconnect power to the appliance before starting; risk of electric shock if powered
• Removal typically requires accessing screws/fasteners at the back of the oven or under the trim; handle edges carefully
• Keep and reuse original fasteners unless damaged; verify button/switch fit before final reassembly

This rear panel is the exterior back cabinet piece that covers and protects a dryer or washer's internal components and provides mounting support for rear-mounted parts. It restores the appliance's structural back and keeps lint, moisture, and debris out. What it does:

• Covers and protects internal components, wiring, and controls located at the appliance rear
• Provides mounting points and alignment for rear-mounted parts and brackets
• Helps reduce drafts, lint intrusion, and pest access through the appliance back
• Stops rattles or vibrations caused by a damaged or loose back panel

• One rear panel/cabinet back

• Disconnect power and water before starting; verify the appliance is fully de-energized
• Remove the dryer/washer top and/or access screws to detach the old rear panel; retain fasteners if reusing
• Align panel tabs and mounting holes, then secure with the correct screws; avoid over-tightening to prevent damage
• If the panel is rusted or sharp, wear gloves and eye protection during removal and installation

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

Color: White.

A front toe panel assembly that restores the lower front trim and airflow opening on compatible laundry appliances. Replaces a damaged or missing lower access panel to keep the cabinet sealed and looking finished. What it does:

• Covers the lower front of the appliance cabinet, protecting internal components from debris.
• Restores the lower air or vent opening and directs airflow as intended.
• Prevents items from falling under the appliance and reduces drafts at the base.
• Helps maintain proper appearance and fit of the appliance front.

• Disconnect power (and gas if applicable) before starting any work.
• Install requires removing the appliance kick strip or lower access fasteners; retain hardware as needed.
• Align panel tabs/clips with cabinet slots and secure with the original screws or clips.
• Replace any damaged clips or mounting hardware to ensure a secure fit.

This is a dryer control board. This part features the buttons and dials that control the dryer and its functions. It is this component that processes the dryer settings that the user chooses. An easy way to determine that the control board is faulty is if the error code F-02 is displaying on the digital display. If this is the case, the control board buttons and lights will not work. This component could stop working after a period of time due to wear and tear. Unplug the dryer from its power source prior to attempting to replace this part. Wear work gloves.The control board is sold individually. It is a genuine OEM part that is sourced directly from the manufacturer. This part is compatible with dryers that are manufactured by Maytag and Whirlpool.

This 6-foot, 4-prong range power cord provides a dedicated 240V connection for electric ranges and stoves, replacing worn or damaged cords to restore reliable power and reduce risk of arcing or intermittent operation. What it does

• Supplies 240V/30A power to the range via a 4-wire (hot/hot/neutral/ground) connection
• Replaces cords with frayed insulation, exposed conductors, or melted ends
• Stops symptoms such as no power to the range, tripping breakers, or intermittent heating
• Ensures a grounded connection when installed correctly

• One 6 ft, 4-prong (30 amp) range power cord, bagged

• Always disconnect household power at the breaker before starting work
• Use the existing strain relief or mounting bracket to secure the cord and prevent tugging

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

The Motor Drive is an OEM part for Whirlpool electric dryers. Located behind the drum, the motor drive contains the electric motor that powers the tumbling and spinning actions of the dryer drum during each cycle. It precisely controls the amount of torque needed to adequately dry wet loads within the preset time parameters.

Symptoms of a bad motor drive include:

• The dryer drum fails to spin or rotates slowly 
• Abnormal noises coming from the back of the dryer
• The dryer takes an extremely long time to finish cycles
• Bulging, cracked, or worn belts around the motor pulley

While heavy loads and continuous usage will eventually wear down motor drives, other causes could be shocks that damage internal mechanisms or failures in motor regulation components over multiple years of heating and cooling. Replacing the drive with a new OEM part restores dependable drying performance. This replacement is also suitable for models from Maytag, Jenn-Air, Amana, Roper, and more.
 

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This drum baffle restores proper tumbling by lifting and separating laundry as the dryer drum rotates. It helps improve drying performance and reduces garment bunching. What it does:

• Lifts and tumbles clothes so air flows more evenly through the load
• Helps prevent garments from clumping or wrapping around the drum
• Can reduce rubbing, thumping, or scraping noises caused by a loose or damaged lifter
• Restores consistent drum contact and improves drying efficiency

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires opening the dryer cabinet or front panel; small tools may be needed
• Align the baffle with factory mounting holes and secure with existing fasteners; use correct screws if replacements are required
• Inspect and replace worn drum or support parts as needed for reliable operation

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

The Valve is an OEM part for Whirlpool dryers. It is responsible for controlling the flow of water into the dryer's steam generator, enabling the steam function during the drying cycle.

A bad water inlet valve can occur due to wear and tear, sediment buildup, or malfunctioning internal components. If you notice symptoms such as no steam being produced during the drying cycle, insufficient steam generation, or water leakage around the valve, it may be time to replace this part.

Symptoms of a bad valve include:

• No steam being produced during the drying cycle
• Insufficient steam generation
• Water leakage around the valve

Restore your Whirlpool dryer by replacing the faulty or damaged steam water inlet valve with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.