Mfi2296vem3 Parts

This foam-in-place door gasket creates an air-tight seal between the door and cabinet, keeping cold air in and humidity out. Replacing a worn gasket helps restore proper temperatures, reduce frost and condensation, and maintain efficiency.

• Seals the door perimeter to prevent warm air infiltration and cold air loss
• Helps maintain interior temperature and moisture balance for reliable cooling
• Common symptoms of failure: torn, cracked, or deformed gasket; poor door seal; condensation or frost at the door; longer run times

• Disconnect power before servicing
• Let the gasket relax at room temperature or warm with hot water to ease installation; avoid excessive heat
• On many models, loosen the inner-door retainer or screws to remove and reinstall the gasket
• Seat corners first, press evenly all around, then adjust hinges/strikes if needed

This replacement motor restores powered rotation to the assembly it drives, bringing smooth, dependable operation back to your appliance. Replacing a weak, noisy, or seized motor can resolve no-run or intermittent performance of the connected function. What it does

• Converts electrical power into controlled shaft rotation to operate the connected mechanism
• Failure signs can include humming or grinding noises, overheating odor, or the feature not starting
• Excess vibration or heat can indicate worn bearings or windings

• 1 motor

• Disconnect power (and shut off water if applicable) before servicing
• Note wire connections and orientation; transfer any brackets, grommets, or attached parts from the original motor if required by your model
• Ensure the shaft spins freely and clearances are correct before reassembly
• Restore power and test; monitor for abnormal noise or heat on first run

This replacement divider separates sections inside a bin or drawer so contents stay organized and in place. Replacing a cracked or missing divider restores proper fit and helps prevent items from shifting or jamming during everyday use. What it does

• Divides a bin, basket, or drawer into sections for better organization
• Helps keep small items upright and prevents contents from sliding together
• Seats into molded slots or tabs to maintain the correct layout
• Common symptoms include cracks, broken tabs, warping, or the divider not staying in place

• 1 divider

• Unplug the appliance before servicing
• Remove the bin/basket or drawer to access the divider
• Release the old divider from its slots or tabs; align and press the new divider firmly into place
• Verify the divider is fully seated and the bin/drawer installs and moves correctly before restoring power

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

This factory screw secures appliance components so they stay aligned and firmly attached during everyday use. Replacing a missing or damaged screw helps stop rattles, looseness, and poor fit that can affect performance over time.

• Fastens panels, brackets, or hardware to keep assemblies tight
• Helps correct issues like loose handles, vibrating panels, or misaligned parts
• Restores proper fit after a screw is stripped, corroded, or lost
• Built to match the original thread and length for reliable engagement

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct driver to avoid stripping the head or threads
• Start threads by hand to prevent cross-threading; tighten snugly without over-torquing
• Replace any companion fasteners that are worn or missing for even clamping

This gasket for the damper assembly provides a replacement seal that helps keep compartments properly isolated and reduces air leakage. Replacing a worn gasket restores more consistent airflow and supports stable internal temperatures. What it does:

• Seals the damper opening to reduce unwanted air transfer between compartments.
• Helps the damper close and regulate airflow for more consistent temperature control.
• Common symptoms of a failing gasket: temperature swings, frost or moisture buildup, and noisy or improperly closing damper.
• Restoring a proper seal can improve cooling consistency and help avoid overworking the compressor.

• Disconnect power to the appliance before attempting service.
• Remove interior items and any trim panels needed for damper access; use gentle prying to avoid damage.
• Seat the new gasket fully into the damper groove and verify smooth damper movement before replacing panels and contents.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Color: White

This 33-inch shaft-rack replaces the rack support shaft that the dishwasher rack slides on, restoring smooth in-and-out movement and correct rack alignment for easier loading and unloading. What it does:

• Acts as the axle for a dishwasher rack, supporting and guiding rack travel along the tub.
• Restores smooth sliding if the original shaft is bent, worn, or broken.
• Helps eliminate rack misalignment, rubbing, or sticking during use.
• Matches OEM fit and mounting points when used with the correct part number.

• Disconnect power and water to the appliance before beginning any repair.
• Remove the affected rack to access the shaft; keep track of end caps or retaining clips.
• Slide out the old shaft and install the replacement, ensuring clips/end caps are properly secured.

This Door Shelf Bin replaces a broken or worn refrigerator door bucket to restore secure storage on the door and keep bottles and small items organized. Designed to mount into the door retainer for stable, everyday use. What it does:

• Provides a dedicated shelf on the refrigerator door to hold bottles, condiments and small containers.
• Replaces cracked, warped or loose bins that allow items to shift or fall when the door opens and closes.
• Restores proper spacing and containment to prevent spills and improve interior organization.
• Matches factory mounting points so the bin seats into the door retainer for a secure fit.

• One door shelf bin

• Disconnect power or unplug the refrigerator before starting any repair to avoid injury.
• Remove all items from the door shelf, then lift and pull the old bin out of the door retainer; retain any clips or screws for re-use if present.
• Align the new bin with the door rails/retainer and slide it into place until it seats; some models may use clips or screws.
• Inspect door retainer clips and mounting points for damage during installation; replace damaged hardware to ensure a secure fit.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

This crisper brace supports the crisper cover/shelf in 30-inch refrigerators, restoring rigidity so the glass doesn't sag and the drawers slide smoothly. Replace a cracked or missing brace to protect the cover and maintain proper drawer alignment. What it does

• Provides structural support for the crisper cover/shelf
• Helps prevent bowing, sagging, or cracking under load
• Keeps crisper drawers aligned for smooth opening and closing
• Common symptoms: broken/warped brace, sagging cover, drawers binding or misaligning

• 1 crisper brace

• Disconnect power before servicing; remove food from the crisper area
• Pull out crisper drawers and lift off the glass/cover
• Release or unfasten the old brace; seat the new brace fully in tabs or screw locations
• Reinstall the cover and drawers; handle glass carefully to avoid breakage

This chute extension yoke is a molded replacement part that secures and guides the chute opening, restoring proper alignment and part fit so items move smoothly through the appliance. It replaces a damaged, cracked, or broken yoke to reduce snagging and rattling. What it does:

• Secures the chute assembly and maintains correct chute alignment
• Guides garments and items into the cabinet opening without catching
• Prevents loose or vibrating chute pieces that can cause noise
• Restores structural support where the original yoke is cracked or worn

• One chute extension yoke assembly

• Disconnect power (and water if applicable) before beginning any repair
• Basic hand tools are typically required; refer to your service manual for disassembly steps
• Inspect surrounding chute and seals and replace any damaged hardware for best fit

A single-pole, single-throw rocker switch that restores reliable on/off control for one electrical circuit. Replacing a worn or failed rocker switch helps return consistent control and stops intermittent or unresponsive operation. What it does:

• Opens and closes a single electrical circuit when the rocker is pressed.
• Common replacement for switches that stick, fail to latch, or cause intermittent power.
• Can stop symptoms such as unresponsive controls, lights or functions that won't turn on/off, or sparks from a worn switch.
• Matches OEM form and function for direct replacement in compatible appliances.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Note wire locations or take a photo before removing terminals to ensure correct reconnection.
• Use appropriate tools and avoid pulling on wires; if terminals are damaged, replace wiring or connectors.

This replacement screw secures appliance panels and components to restore proper fit and reduce vibration. A straightforward fastener that helps keep parts aligned and prevents noise or loose trim from worsening. What it does:

• Fastens panels, brackets, or trim pieces to the appliance frame
• Helps stop rattling or vibration caused by loose or missing hardware
• Restores proper alignment where original screw has been lost or damaged
• Works wherever the OEM screw specification is required for secure mounting

• Turn power off and unplug the appliance before working on it
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening to prevent damage to threads or plastic parts
• Keep removed fasteners organized so you reinstall the correct pieces