Mgd5 Parts

The CONTROL PANEL is an OEM component specifically designed for Whirlpool electric dryers. It houses the interface that users interact with to select cycles and monitor dryer functions.

The control panel is designed to withstand high heat and vibration within the dryer environment. Its electronic components and display regulate vital processes such as temperature selection, timer countdown, and sensor dry settings. 

Causes of a bad control panel can include liquid damage, failure of electronic modules, or worn-out buttons and touch points.

Symptoms of a bad control panel include:

• Unresponsive or non-functional buttons 
• Inability to select desired cycles 
• Erratic timer display or premature cycle shut-off
• Repeated error codes appearing

This Whirlpool control panel is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.

This replacement power cord restores AC power delivery to the appliance when the original cord is worn or damaged. It provides a direct, durable connection from the wall outlet to the appliance for reliable operation. What it does:

• Supplies mains power to the appliance so it can operate normally
• Replaces frayed, cut, or melted cords that cause intermittent power or safety concerns
• Helps stop symptoms like the appliance not powering on or losing power during use
• Replaces cords with damaged insulation or exposed wiring that may present a shock or fire risk

• Always disconnect power at the breaker or unplug the appliance before servicing
• Route cord and secure strain relief as shown in your appliance wiring diagram

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

This replacement control knob is the dial used to adjust settings on compatible Whirlpool ranges and cooktops, restoring reliable tactile control and clear indicator alignment. It gives a simple, direct replacement for worn or broken knobs. What it does:

• Replaces a damaged, cracked, or missing control knob to restore user control
• Provides a firm push-on fit for accurate indicator alignment with settings
• Helps eliminate slipping or rounded-off edges that make adjustments difficult
• Designed to match the original fit and feel for safe, predictable operation

• Disconnect power to the appliance before beginning any work
• Pull the old knob straight off the shaft; press the replacement knob firmly onto the shaft until seated
• If the knob is tight or hard to remove, use a cloth and steady, even force to avoid damaging the shaft or surrounding trim

This is a drum assembly intended for use with dryers. This part can be found inside the dryer and is responsible for holding clothing while a cycle is running. It holds wet laundry while loading the appliance. Over time and with use, the drum assembly can start to wear out. This can cause the dryer to squeal, start and stop during a cycle, make buzzing noises, or seize up.If the drum assembly is damaged, it will need to be replaced. Make sure to have basic tools and a pair of work gloves ready. The dryer should be turned off and unplugged from the wall. Raise the top panel, remove the front panel, and then remove the drum. The drum support roller should be taken out and installed on the new drum. Reinstall with the new component and reassemble all parts before use.The drum assembly is made to be used with dryers and washer/dryer combos from Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold on an individual basis.

A replacement mounting bracket that secures internal components and restores proper alignment for affected appliance assemblies. Replaces a worn or damaged bracket to stop movement and reduce noise caused by loose parts. What it does:

• Provides a stable mount point for internal panels or components to keep assemblies aligned.
• Stops rattling, vibration, or misalignment caused by a broken or bent bracket.
• Restores proper fit and spacing where the original bracket has failed.
• Helps prevent further wear to adjacent parts by keeping components secure.

• Disconnect power and/or gas supply before accessing internal parts.
• Basic hand tools required; follow the appliance service manual for correct removal and installation steps.
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection.

Color: White

Color: White.

A front toe panel assembly that restores the lower front trim and airflow opening on compatible laundry appliances. Replaces a damaged or missing lower access panel to keep the cabinet sealed and looking finished. What it does:

• Covers the lower front of the appliance cabinet, protecting internal components from debris.
• Restores the lower air or vent opening and directs airflow as intended.
• Prevents items from falling under the appliance and reduces drafts at the base.
• Helps maintain proper appearance and fit of the appliance front.

• Disconnect power (and gas if applicable) before starting any work.
• Install requires removing the appliance kick strip or lower access fasteners; retain hardware as needed.
• Align panel tabs/clips with cabinet slots and secure with the original screws or clips.
• Replace any damaged clips or mounting hardware to ensure a secure fit.

Size: 6 - 20 x 1 1/16 inch.