Mvwb85owq1 Parts

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This is a replacement washer washplate cap that will work for several models of washers. This cap fits over the washplate mounting bolt located in the washer and protects the bolt from water. It ensures that clothing does not catch on the washplate, which could damage the clothes. If the cap becomes damaged, it should be replaced.The metal washplate cap is durable and long-lasting, so it should not need to be replaced often. However, if it is coming loose or has been damaged, it can be replaced with relative ease. They should always unplug the washer before starting any type of repair or replacement. They should also wear work gloves to protect their hands when replacing the cap.The washer washplate cap works on certain models of washers from Whirlpool and Maytag. This part is sold individually, and it is an OEM replacement that has been sourced directly from the manufacturer.

This drain pump assembly moves water out of the appliance during the drain portion of the cycle. Replacing a weak or failed pump restores proper draining and helps prevent standing water, odors, or repeated drain attempts.

• Actively pumps wastewater through the drain hose to household plumbing
• Engages during the drain step to clear the tub/sump between and after cycles
• Typical failure symptoms: won't drain or drains slowly; water left in the bottom; loud humming/grinding during drain; leaks around the pump area
• May fail due to worn motor, damaged impeller, or debris lodged inside the pump

• Disconnect power and turn off water supply; bail or wet-vac any standing water before starting
• Keep towels or a shallow pan ready; clamp or plug hoses to control residual water
• Transfer hose connections and any mounting hardware from the original pump; ensure seals and clamps are seated firmly
• After installation, run a short cycle to check for leaks

This factory fastener secures appliance components so panels, brackets, and trim stay tight and aligned. Replace a missing or stripped screw to stop rattles, restore a secure fit, and keep parts mounted as designed.

• Fastens panels, brackets, covers, and trim to the chassis
• Restores proper alignment and reduces vibration or rattling
• Replaces missing, rusted, or stripped hardware
• Helps maintain a solid, factory-style fit after service

• Disconnect power (and water, if applicable) before servicing
• Match the original screw location and orientation; start threads by hand to avoid cross-threading
• Use the correct driver for the head type; tighten snugly without overtightening
• Reuse any original washers or clips if present

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This low-profile washplate sits at the bottom of the tub and moves the load through water for proper cleaning. Replace a stripped, cracked, or loose washplate to restore wash action and reduce noise or slippage.

• Mounts to the drive hub to rotate and circulate laundry during the wash cycle
• Helps create water currents and friction to loosen soils
• Worn or stripped splines can cause slipping and poor agitation
• Common symptoms: clothes not moving, poor cleaning results, unusual clicking/grinding from the tub base, visible cracks or wobble

• Disconnect power and shut off water before servicing
• Remove the center cap/cover, then remove the retaining bolt and lift off the old washplate
• Clean and inspect the hub splines; seat the new plate fully and reinstall the bolt—do not overtighten
• Run a short test cycle to ensure proper wash action

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

This washer impeller mounts at the bottom of the tub to generate the water currents that move and roll garments during the wash cycle. Replacing a cracked or stripped impeller restores proper turnover and cleaning performance.

• Creates the wash action by circulating water and moving fabrics through the load
• Secures to the drive hub; worn splines or a damaged center can cause slippage
• Common symptoms: poor cleaning, clothes not moving during wash, clicking/grinding from the wash plate area, visible cracks or looseness
• Direct replacement for the low-profile agitator "wash plate" style

• Disconnect power and turn off water supply before servicing
• Remove the center cap and retaining screw/bolt; lift the old impeller straight up
• Clean the hub splines; seat the new impeller fully and tighten the fastener securely
• Avoid prying against the tub; test on a short cycle to ensure proper wash action

Small but essential, this drain hose retainer is a clip that secures the hose in place during use or storage. It keeps the hose properly routed to help prevent kinks, pull-outs, and leaks. What it does:

• Holds the drain hose to the cabinet/frame for correct routing or stowage
• Helps prevent kinks, abrasion, and strain that can cause poor draining or leaks
• Replaces a broken, warped, or missing retainer so the hose stays put
• Common symptoms: hose won't stay clipped, falls during operation, visible damage, water near hose path

• 1 drain hose retainer

• Disconnect power and turn off the water supply before servicing
• Access the hose routing area and remove the damaged retainer
• Position and fasten the new retainer in the same location; route the hose through it
• Run a brief test to ensure secure routing and no leaks

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Left side hinge

This recirculation hose routes wash water back through the tub during the cycle. A fresh, intact hose helps maintain proper water flow and prevents leaks, supporting consistent cleaning performance.

• Directs water from the pump back into the tub for continued circulation
• A cracked, kinked, or leaking hose can cause water leaks or poor wash performance
• Can help resolve issues like low recirculation flow or visible water drips during operation
• Restores correct internal water routing as designed

• Disconnect power and water supply before servicing
• Have towels or a shallow pan ready to catch residual water
• Note hose routing and clamp positions before removal; reuse or replace clamps as needed
• After installation, run a quick cycle to check for leaks and proper flow

The fabric softener dispenser stores liquid softener and automatically releases it during the rinse cycle. Replace a cracked, clogged, or missing dispenser to restore reliable dispensing and reduce leaks or softener left behind. What it does:

• Holds liquid fabric softener and dispenses it at the proper time in the rinse cycle
• Helps prevent early release of softener onto clothes
• Common symptoms: softener not dispensing, softener remaining in the cup after the cycle, leaks/drips from the dispenser area, or visible damage/missing dispenser
• Can resolve clogs from residue buildup that interfere with siphoning/flow

• 1 fabric softener dispenser

• Disconnect power and turn off water supply before servicing
• Remove the old dispenser (pull straight up or release locking tabs, per model)
• Clean any residue from the mounting area; flush the new dispenser with warm water
• Seat the new dispenser fully and test with a small amount of water to ensure proper flow

This lid bumper cushions the top-load washer lid as it closes, reducing noise and preventing direct contact between the lid and cabinet. Replace a missing or worn bumper to help protect the lid finish and ensure a smoother close.

• Provides a soft stop at the lid's contact point to absorb impact
• Helps reduce closing noise and lid rattle
• Helps prevent scuffs or chips on the lid edge or cabinet top
• Common signs of failure: bumper missing, flattened, cracked, or louder slam when closing

• Disconnect power before servicing the appliance
• Open the lid and locate the factory bumper position(s) per your parts diagram
• Remove the old bumper and any debris; seat the new bumper firmly in the designated location
• Close the lid gently to verify proper contact and alignment

Size: 1/4 inch hex head, 10-12 x 1/2 inch.