Mvwx500w1 Parts

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

This wire harness routes power and signals to lower VMW components, restoring proper electrical connection and reliable operation for affected circuits. It replaces a damaged or worn lower harness assembly to help eliminate intermittent power or control issues. What it does:

• Carries electrical power and control signals between lower VMW components and the main wiring system
• Re-establishes secure plug-and-play connections when wires are frayed, broken, or connectors are loose
• Addresses symptoms such as intermittent operation, no power to lower components, or control malfunctions
• Prevents shorts and poor contacts caused by damaged insulation or broken terminals

• Disconnect power before starting any repair to avoid shock or injury
• Handle connectors by the housings; do not pull on wires when removing or installing
• Route and secure the harness following the appliance wiring path and any retaining clips to prevent chafing
• Verify all connectors are fully seated and inspect for pin damage before reapplying power

This replacement power cord restores the appliance's primary electrical connection so it can receive power safely. Use it when the original cord is damaged, frayed, or no longer providing a reliable connection. What it does:

• Provides the main incoming electrical connection from the wall outlet to the appliance
• Replaces cords with visible damage, exposed wiring, or intermittent power delivery
• Can resolve no-power or power-interruption symptoms when the cord is the fault
• Ensures a secure connection when installed with the correct strain relief and terminal fastening

• Disconnect the appliance from power before attempting any service.
• Remove access panels as needed to reach the cord terminals; note wire locations before disconnecting.
• Secure cord with the appliance's strain relief and tighten terminal connections per the factory layout.

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

This cycle selector switch controls the washer's cycle selection, letting the timer and controls know which wash program to run. Replacing a worn switch restores reliable cycle selection and predictable machine behavior. What it does

• Selects the active wash cycle and sends the selection signal to the timer/control assembly
• Ensures the washer follows the chosen program (wash, rinse, spin) in the correct sequence
• Common symptoms of a failing switch: washer won't change cycles, cycle knob feels loose or spins freely, machine starts the wrong cycle, or no response when selecting a cycle
• Matches original function and mounting for direct replacement when this exact part is specified

• One cycle selector switch

• Disconnect power (unplug or switch off breaker) before starting any work
• Access typically requires removing the console or control panel—keep track of screws and fasteners
• Note wiring locations or take a photo before disconnecting connectors to ensure correct reassembly

Note: Bearings are only available with the gearcase assembly.

This replacement silverware/cutlery basket holds utensils securely during dishwasher cycles to keep items organized and allow thorough cleaning. Durable molded plastic resists staining and lets water and detergent reach utensils for better wash performance. What it does

• Holds forks, knives and spoons in place so utensils don't fall through the lower rack
• Allows water and detergent to circulate around cutlery for improved cleaning
• Helps prevent scoring and nesting of utensils for more even washing
• Restores organization to the dishwasher's lower rack when the original basket is cracked or missing

• One replacement silverware/cutlery basket

• No special tools required; simply set the basket into the lower dishwasher rack
• Handle carefully to avoid sharp utensils during installation
• Follow dishwasher manufacturer's safety instructions and disconnect power if recommended before servicing

This spacer positions and secures components in place to maintain proper alignment and clearance. It helps reduce vibration and wear by keeping parts correctly spaced inside the appliance. What it does:

• Provides stable separation between panels, brackets or components to ensure correct fit
• Helps prevent rubbing, vibration noise, and premature wear caused by misaligned parts
• Used where a precise gap or mounting offset is required for proper operation
• Commonly installed during repairs or when replacing damaged mounting hardware

• Inspect surrounding mounting points and fasteners; replace any stripped or damaged hardware
• Use correct fastener torque and avoid over-tightening to prevent deformation
• Disconnect power to the appliance before working in or near electrical components

This is a Whirlpool washing machine basket. The washing machine basket holds laundry during a wash cycle. The basket may become damaged over time due to normal wear and tear, which can be exacerbated by overloading laundry or using the wrong amount of detergent. When the basket starts to become damaged or malfunction, noticeable noise increases may take place during use. Eventually, the damage will lead to the basket failing to spin. The old basket can be removed by first removing the top portion by pushing the fastening clips that hold it in place. After removing the top, reach down to remove the softener cup. Using a socket, unfasten the agitator at the bottom of the basket. After removing the agitator, the basket should easily lift out of the machine.This part is a genuine OEM product and is sourced directly from the manufacturer. It is intended for use in Whirlpool, Maytag, Kenmore, and Crosley appliances.