Nfw7300 Parts

This replacement frame restores the structural support for the component it holds, helping it fit securely and operate smoothly. Replace a cracked, warped, or broken frame to bring back proper alignment and stability.

• Provides rigid support and correct alignment for the attached component
• Maintains proper spacing and level so items sit correctly
• Helps associated drawers or bins slide and seat smoothly where applicable
• Common signs of failure: cracks, broken tabs, warping, wobble, or poor fit

• Disconnect power before servicing
• Remove the affected assembly and set aside any inserts or hardware from the old frame
• Transfer reusable parts (such as glass, rails, or gaskets) to the new frame
• Ensure the frame is fully seated and avoid overtightening any fasteners

This replacement outer frame restores the appliance's finished appearance and helps keep panels and components aligned for reliable operation. It's the visible trim piece that supports and secures adjacent parts. What it does:

• Provides structural support and cosmetic trim for the appliance front or panel area.
• Helps align and secure doors or access panels to prevent gaps and improper sealing.
• Reduces vibration and rattling by holding panels firmly in place.
• Replaces cracked, bent, or damaged frame pieces that cause misalignment or poor fit.

• Disconnect power to the appliance before starting any repair.
• Use appropriate screwdrivers; keep removed fasteners for reassembly.
• Handle edges carefully — trim pieces may have sharp metal or glass attachments.

This is a single replacement screw used to secure appliance panels and components. It restores proper fastening to help eliminate looseness and rattling and keep parts aligned for safe operation. What it does:

• Secures trim, panels or internal components to maintain proper alignment
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or stripped screws for safe, reliable fit
• Works wherever the OEM screw specification and fit match the original

• One screw as shown

• Disconnect power and/or gas before accessing internal components
• Use the proper driver size and avoid over-tightening to prevent thread damage
• Verify correct screw placement against the appliance's service diagram

This rear tub is the OEM replacement outer tub section that supports the wash basket and helps contain water inside the washer cabinet. Replacing a damaged rear tub restores proper drum alignment and helps prevent leaks. What it does:

• Supports the back of the wash basket and provides a mounting surface for the tub seal and bearings
• Helps contain water in the wash chamber to prevent cabinet leaks
• Restores proper drum alignment to reduce rubbing, vibration, and noise
• Addresses symptoms such as visible cracks or holes in the tub, persistent water leaks, or a misaligned/noisy drum

• Disconnect power and water supply before beginning any repair
• Drain the washer and remove the top, front, or rear panels as required for access
• Support the drum and follow the OEM disassembly sequence to avoid damaging seals or bearings
• If seals, bearings, or suspension components show wear, replace them at the same time for best results

This door hinge assembly replaces a worn or damaged refrigerator door hinge to restore proper pivoting and alignment so the door opens and closes smoothly and seals correctly. What it does

• Provides a secure pivot point so the door swings properly.
• Restores correct door alignment to help the gasket seat and reduce air leaks.
• Stops or reduces door sag, sticking, or uneven gaps.
• Helps eliminate grinding or metal-on-metal noise from a failing hinge.

• Disconnect power to the appliance before beginning any repairs.
• Remove door contents and support the door; use two people for heavy doors to avoid injury or damage.
• Retain original mounting hardware unless damaged; torque fasteners snugly and check door alignment after installation.

This console is the outer control panel housing that holds the range's control components and user interface, restoring a finished appearance and secure mounting for the touchpad, knobs, and display. What it does:

• Provides the structural housing for control buttons, displays, and indicator lights.
• Replaces cracked, warped, or damaged panels that expose internal electronics or prevent controls from seating properly.
• Helps stop rattling or loose controls by restoring proper alignment and mounting points.
• Restores the appliance's finished look and protects internal components from spills and debris.

• Disconnect power to the appliance before starting any work.
• Handle edges carefully; plastic panels and trim can be sharp or brittle.
• Installation typically requires removing the cooktop or control assembly; keep fasteners and note screw locations.
• Avoid touching circuit boards or connectors and follow anti-static precautions.

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

This front counterweight mounts to the washer's outer tub to stabilize the drum assembly during spin. Replacing a cracked or loose weight helps curb excessive vibration, banging, and walking, restoring smoother, quieter operation.

• Adds mass at the front of the outer tub to help balance loads during spin
• Controls vibration and noise; reduces walking and off-balance interruptions
• Typical failure signs: cracked or broken weight, missing chunks, loose/rattling mount, loud knocking, severe shaking
• Visible damage to the weight or mounting area can indicate replacement is needed

• Unplug the washer and turn off water supply; wear gloves. The weight is heavy—use a second person if needed
• Support the tub and access the front of the outer tub; remove the original weight carefully to avoid damage
• Transfer and reuse any mounting hardware from the original part if needed; seat the new weight flush and tighten bolts evenly
• Run an empty test spin; inspect shocks/suspension and leveling

This rubber seal fits around the water temperature sensor where it passes through the tub or housing. It restores a watertight barrier at the sensor port to help prevent leaks and ensure reliable temperature feedback.

• Creates a watertight seal around the temperature sensor
• Helps prevent drips or leaks from the sensor opening
• Supports stable, accurate temperature readings during cycles
• Typical failure signs: cracked, flattened, or brittle seal; moisture at the sensor area; pooling water beneath the unit; temperature-related faults

• Disconnect power and turn off water supply before servicing
• Access the sensor location and drain any remaining water
• Withdraw the sensor, remove the old seal, and clean the seating surface
• Lightly moisten the new seal with water, seat it fully, reinstall the sensor, and check for leaks during a test cycle

Rear counterweight that stabilizes the washer tub during spin cycles to reduce vibration and excessive movement. Restores balance for smoother, quieter operation and helps prevent premature wear from uncontrolled drum motion. What it does:

• Adds mass to the back of the washer tub to counterbalance loads and limit rocking and vibration during spin cycles.
• Common symptom: washer vibrates, rocks, bangs, or moves across the floor during spins.
• Replacing a cracked, loose, or missing rear counterweight often reduces noise and improves spin stability.

• Disconnect power before starting work; follow all safety precautions in your model's service manual.
• Support the tub or cabinet before removing/installing the counterweight; the part can be heavy—use two people or appropriate lifting support.
• Ensure correct orientation and securely tighten mounting hardware; run a short test spin to confirm balance after installation.

This siphon routes liquid bleach and fabric softener from the dispenser into the washer tub so additives are delivered at the correct time in the cycle. Replacing a faulty siphon restores proper dispensing and helps prevent leaks or staining. What it does:

• Directs bleach and fabric softener from the dispenser to the wash drum during the appropriate cycle.
• Ensures additives are introduced at the correct time for consistent wash results.
• A cracked, clogged, or broken siphon can cause poor dispensing, leaks, or product staining.
• Designed to fit into the dispenser assembly and work with the washer's existing dispenser plumbing.

• Disconnect power (and water if recommended) before servicing the appliance.
• Basic hand tools may be required; refer to the washer's service manual for disassembly steps.
• Handle plastic components gently to avoid cracking or misalignment of sealing surfaces.

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This wire harness connects the motor to the appliance's power and control wiring, restoring reliable electrical connection for motor operation. It replaces a damaged or worn harness to help restore normal motor function. What it does

• Carries power and control signals between the motor and the main wiring harness or control board
• Can resolve intermittent motor operation, no-start conditions, or loss of motor power when the fault is a damaged connector or wiring
• Replaces frayed, burned, or broken wires and damaged connector ends that prevent proper motor function
• Helps prevent arcing and poor connections that can cause overheating or electrical faults

• One motor wire harness

• Disconnect power to the appliance before beginning any repair to avoid electrical shock
• Verify the harness matches the original by comparing connector shapes and pin count before installation
• Route and secure the harness away from moving parts and sharp edges; use existing clips or ties
• If you see damage to the motor or control board connectors, inspect those components and replace as needed

This oven door glass replaces a cracked or broken glass panel so the door seals and you can safely see inside while cooking. It restores the oven door's protective barrier and appearance. What it does:

• Replaces damaged or cracked oven door glass to prevent heat loss and sharp edges
• Restores visibility into the oven cavity for safe monitoring of food
• Helps the door maintain proper sealing when paired with intact gaskets and hardware
• Reduces risk of glass shards or injury from a compromised panel

• Handle with care; glass is fragile—use gloves and eye protection during removal and installation
• Disconnect power and allow the oven to cool before working on the door
• Follow the oven manufacturer's instructions for removing the door and fastening the glass
• If door hardware or seals are damaged, inspect and replace them separately