Ngm8656uc Parts

This clamp secures flexible hoses and small tubes to fittings, keeping connections tight to help prevent leaks and movement. It's a small replacement clip used on water and drain lines in many appliances. What it does

• Holds a hose or tube firmly to a barb or nipple to maintain a sealed connection
• Helps stop leaks caused by loose or damaged hose connections
• Prevents hoses from slipping off during operation and reduces vibration noise
• Used wherever a small retaining clamp is required on water or drain lines

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide clamp over the hose, push hose fully onto the fitting, then compress or tighten clamp as required
• Use pliers or the correct tool for the clamp type; avoid damaging the hose when installing
• Replace if corroded, cracked, or not seating properly

The Tube is an OEM part for Bosch cooktops. It provides stable containment for the gas burners that allow for cooking flexibility. Precise flame control delivers heating power for any cooking task. 

Causes of a bad gas tube cooktop can include cracks or damage to the enamel surface as a result of pots sliding or debris falling. Wear and tear of internal components like control valves or pilots over time also indicates the need for replacement.  

Symptoms of a bad tube include:

• Flames that cannot be adjusted or controlled properly
• Burners that are difficult to ignite or stay lit  
• Cracks or chips in the enamel surface exposing metal below

This OEM Bosch part is also compatible with Thermador and some Kenmore models. 

This cable harness is the factory-style wiring assembly that connects electrical components, making it easier to restore reliable power and signal paths in the appliance. Replaces damaged or frayed harnesses to help resolve intermittent or no-power issues. What it does

• Routes and connects power and control signals between components (connectors included).
• Restores electrical continuity when worn, pinched, or damaged wiring causes failures.
• Common symptoms: appliance won't power on, controls unresponsive, intermittent operation, or visible burned/ frayed wires.
• Helps prevent short circuits caused by exposed conductors when replaced promptly.

• One complete cable harness as shown

• Disconnect all power (unplug or shut off circuit) before starting repairs.
• Label or photograph connector locations before removal to ensure correct reassembly.
• Avoid crushing or kinking the harness; route and secure per original routing to prevent wear.
• Replace with the exact part number to ensure correct fit and connector types.

The Holder is an OEM part for Bosch cooktops that provides a reliable and efficient ignition process for your cooktop burners. The burner igniter is responsible for generating the spark necessary to ignite the gas coming from the orifice holder. The orifice holder controls the flow of gas from the gas supply to the burner, while the tube connects the orifice holder to the burner head.

A bad holder can lead to issues with burner ignition, such as failure to light or inconsistent sparking. Possible causes of a bad assembly include worn-out igniter electrodes, clogged orifice holders, or damaged tubes.

Symptoms of a bad holder may include:

• Difficulty in igniting the burner
• Inconsistent sparking or weak spark
• Gas smell from the orifice holder 

Replace your faulty holder with this genuine OEM Bosch part to restore your cooktop burners. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This is a replacement oven shelf grid that restores a stable cooking surface for pots, pans and bakeware. It returns lost support so cookware sits level and heats evenly. What it does:

• Provides a durable, wire shelf surface to hold cookware inside the oven
• Replaces a missing, bent or damaged shelf that causes pans to tip or slide
• Helps maintain even air circulation around bakeware for consistent cooking
• Matches the original shelf shape and mounting points for a secure fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Wear gloves to protect hands from sharp edges during removal and install
• Remove oven racks and follow the owner's manual for proper shelf placement

This retaining washer secures a control shaft or hub to keep components in place during operation, helping restore proper control movement and prevent parts from sliding off the shaft. Simple replacement when a worn or missing retainer causes loose knobs or shifting parts. What it does:

• Fits onto a control or drive shaft to hold a knob, hub or gear in position
• Prevents axial movement that can cause loose or slipping controls
• Commonly replaced when the original washer is bent, cracked, or lost
• Works with compatible Bosch control assemblies and hubs

• One retaining washer

• Recommended for users comfortable with basic appliance disassembly; unplug appliance before starting
• Remove the control knob or panel per model instructions to access the shaft
• Press the washer into place on the shaft until fully seated; verify proper fit and control operation

This replacement door gasket seals the dishwasher door to keep water inside the tub and help maintain wash performance. It restores a tight door seal to reduce leaks and prevent water from pooling around the appliance. What it does:

• Creates a watertight seal between the door and tub to stop leaks during cycles
• Helps prevent water from dripping onto floors and surrounding cabinetry
• Reduces steam and moisture escape that can cause odors or damage
• Restores proper door closure where worn or flattened seals allow seepage

• Disconnect power and water supply before attempting any service.
• Inspect surrounding door edges for damage and clean mounting surfaces before installing the new gasket.
• Press the gasket firmly into the door channel; some models require partial door disassembly.
• After installation, run a short cycle and check for leaks before returning the dishwasher to regular use.

This replacement part is a cooktop burner grate set for gas stoves. The cooktop burner grate set are the pieces that cookware sits on above the burners. Grate sets provide a stable cooking surface for pots and pans.To replace the grate set, simply remove the old grates from the stove. Lift them off and set them to the side. Install the new grates by placing them in their appropriate positions. Once placed properly, make sure they are secure and level on the stove. Place a pan on the grate set to see if it sits evenly on the stove. If so, the installation was a success.This genuine OEM part is compatible with Bosch, Gaggenau, and Thermador gas stoves.

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where the original screw is missing, stripped, or damaged to help keep parts aligned and stable. What it does:

• Fastens panels, brackets, or components to maintain proper alignment and operation
• Replaces a lost, stripped, or damaged screw to prevent rattling or loose parts
• Provides the same basic fastening function as the original hardware
• Suitable where the appliance requires a small machine/tapping screw of the correct size and thread

• One replacement screw

• Use the correct screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure proper engagement before tightening
• Tighten snugly but avoid over-torquing which can strip threads or damage parts
• Disconnect power to the appliance before working on or removing panels where appropriate;

This replacement cable is a direct-replacement wiring harness used to restore electrical connections for the appliance control and components. It provides the needed wiring continuity so controls and sensors can communicate reliably. What it does:

• Reestablishes a secure electrical connection between components and the main control
• Restores signal/power routing when a frayed or damaged wire causes intermittent operation
• Can resolve symptoms such as failure to power on, intermittent cycles, or related error codes tied to wiring faults
• Prevents shorting or poor contact that can lead to inconsistent appliance behavior

• Recommended for technicians or experienced DIYers; disconnect power before replacing
• Verify matching connector shapes and wire colors before installation
• Route the cable away from heat and moving parts to avoid future damage