Pdf4085kf Parts

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This is the display/control circuit board for the refrigerator's user interface. It drives the temperature/readout display and processes button inputs so you can adjust settings and dispenser functions from the front panel.

• Manages the front-panel display and keypad signals
• Helps when the display is blank or dim
• Helps when buttons don't respond or settings won't change
• Helps with erratic or incorrect temperature readouts

• Disconnect power to the refrigerator before servicing
• Use proper ESD precautions when handling the board
• Take photos of wire/ribbon connections to ensure correct reassembly
• After installation, restore power and verify display and button operation

This side blaster assembly mounts to the dishwasher's tub wall and directs a focused spray into the wash cavity to help scour stuck-on residue. Replace if the nozzle is cracked, clogged, or leaking to restore proper cleaning performance.

• Provides targeted side-wall spray to supplement the main wash arms
• Helps flush debris and improve coverage along racks and corners
• Common failure signs: weak or no side spray, poor cleaning near the side wall, visible cracks, or leaks at the side jet
• Restores intended spray pattern and water distribution when the original is damaged or blocked

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack to access the side blaster location
• Release the retainer/screw, disconnect the hose/tube, and install the new assembly; ensure the sealing surface is clean and properly seated
• Reconnect, secure, and run a test cycle to check for leaks and proper spray

This replacement flood stem holds and guides the washer's water-level float so the machine can detect and control water levels. Replaces a worn or damaged mounting tube to restore reliable float operation. What it does:

• Secures and positions the water-level float inside the tub or housing
• Allows the float to move freely so the machine senses proper water level
• Helps prevent overfill and incorrect fill-level behavior when functioning correctly
• Common symptoms of a faulty unit: incorrect water level, washer overfills or fills unevenly, or the machine shows fill/drain issues

• One flood stem

• Disconnect power and turn off the water supply before starting any repair
• Replacement typically requires access to the washer cabinet/top or inner tub area
• Handle the float and tube gently to avoid damage; ensure proper seating and alignment during reassembly
• After installation, run a short fill/drain cycle to confirm correct float operation and that there are no leaks

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

Keep your dishwasher draining properly. This drain hose kit channels wastewater from the tub to your household drain, replacing a cracked, kinked, or leaking hose to help prevent leaks, odors, and standing water at the end of the cycle.

• Carries discharge water from the dishwasher to the sink drain or disposer
• Helps prevent backflow when routed with a proper high loop or air gap
• Replace if the hose is brittle, split, kinked, or clogged
• Common symptoms: standing water after a cycle, slow/no drain, leaks under the sink or at the base

• Disconnect power and turn off water; place a towel to catch residual water
• Access the hose connections at the pump and at the sink/disposer/air gap
• Route the new hose with a high loop or to an air gap per local code; avoid sharp bends and kinks
• Secure all connections with clamps and run a short cycle to check for leaks

This condenser fan motor circulates air across the refrigerator condenser to help remove heat and support efficient cooling. Replacing a faulty motor restores proper condenser airflow and can prevent temperature rise and compressor overwork. What it does:

• Spins the condenser fan to draw air across condenser coils, aiding heat dissipation
• Helps the compressor run efficiently by preventing condenser overheating
• Common symptoms of failure: refrigerator or freezer running warm, motor not running, humming, or loud/abnormal fan noise
• Can cause longer run cycles and higher energy use when airflow is restricted or stopped

• Disconnect power to the appliance before starting any repair
• Handle the fan blade and condenser fins carefully to avoid damage
• Verify wiring and mounting locations match the original; secure all connectors and fasteners

The Upper Rack Bracket Assembly is an OEM replacement part for  GE dishwashers. It is located inside the dishwasher tub and functions to securely mount the upper dish rack. It allows for adjustable height positioning and prevents rack movement during washing.

Causes of a bad upper rack bracket assembly can include cracks or breaks in the mounting points, stripped screw holes allowing rack sway, or deformities preventing proper seating.

Symptoms of a bad upper rack bracket assembly include: 

• Loosening or detaching of the upper rack during the cycle  
• Restricted rack adjustment or inability to set desired height
• Noise or vibration from an unsecured rack vibrating against the tub

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Conduit Main Assembly is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper wash arm, and is responsible for securely mounting and holding the upper wash arm in place during operation.  

Causes of a bad upper wash arm support include:

• Symptoms of a bad upper wash arm support include: 
• Vibration or noise from an unsecured wash arm
• Improper alignment of spray pattern
• Restricted rotation of the wash arm during washing  
• Leaks at the tub connection point

Symptoms can include cracks or breaks that compromise its structure, or wear over extended use without replacement.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This insulation bag assembly installs around the dishwasher tub to dampen operating noise and limit heat transfer. Replace when the original insulation is missing, damaged, or saturated to help maintain quieter cycles and protect nearby cabinetry. What it does:

• Provides an acoustic and thermal barrier along the tub exterior
• Helps reduce cycle noise and vibration
• Helps minimize heat and moisture reaching surrounding cabinets
• Replacement may help with louder operation, warm exterior panels, or increased condensation

• 1 insulation bag assembly

• Disconnect power at the breaker and shut off the water supply; remove toe panel and slide the dishwasher out for access
• Wear gloves/long sleeves when handling insulation
• Position in the factory location without pinching wiring or blocking vents, door seals, or moving parts
• Reinstall panels, level the unit, restore power/water, and run a test cycle to verify proper operation and no leaks

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw

This detergent plate is the replacement dispenser component that holds and releases detergent during the wash cycle, ensuring detergent is delivered when the machine runs for proper cleaning performance. What it does

• Holds detergent inside the dispenser area until the wash cycle calls for release.
• Opens or allows detergent to be flushed into the wash chamber at the correct time.
• Common symptom: detergent stays in the dispenser and doesn't release, leaving dishes or laundry soiled.
• Common symptom: damaged, cracked or warped plate can prevent proper release or seating of detergent.

• One detergent plate

• Disconnect power (and water if applicable) before accessing the dispenser to avoid shock or injury.
• Handle the plate carefully; plastic parts can crack if forced or over-tightened.
• Remove the door/dispenser trim per your model's service instructions to access the plate; reinstall ensuring proper alignment so the dispenser seals and operates correctly.

The Vent Fan Assembly is an OEM replacement part for GE dishwashers. As a key ventilation component, the vent fan is responsible for drawing moisture-laden air out of the dishwasher tub and venting it outside during and after the wash cycle. It plays an important role in effectively drying dishes and preventing mold or odor issues.

Causes of a bad vent fan include a failing motor, broken or cracked fan blades, or an obstructed vent opening. 

Symptoms of a bad vent fan include:

• Incomplete or slow drying of dishes
• Excess moisture remaining in the tub at the end of the cycle  
• Mold or mildew growth inside the dishwasher
• Strange noises or vibrations coming from the vent area

Over time, the vent fan motor and blades can degrade due to continuous use. This part is also compatible with ASKO, Crosley, Inglis, Magic Chef, RCA, and some Kenmore models.
 

This clip secures the fold-down tine row to the flat rack in your dishwasher, keeping the section stable during loading and washing. Replace a broken or missing clip to stop collapsing tines and restore smooth rack function. What it does:

• Holds the fold-down tine assembly to the rack wire
• Helps tines stay upright or folded as intended
• Addresses a loose, wobbly, or collapsing tine row
• Common replacement when the original clip cracks or goes missing
• Reduces rattling caused by an unstable tine section

• Disconnect power at the breaker before servicing.
• Remove the rack to access the clip location.
• Note orientation; snap the new clip onto the rack wire/tine bar until fully seated.
• The tine row moves smoothly and locks as intended before reinstalling the rack.

The Flat Chrome Badge is an OEM part for GE refrigerators. It is responsible for displaying the GE logo and model information on the front of the refrigerator. As an identifiable brand marker, the badge contributes to the overall appearance and style of the appliance.

Causes of a bad badge can include damage from impacts or bending, discoloration or tarnishing over time, or simple wear and tear that renders the badge appearance faded or illegible.

Symptoms of a bad badge include:

• A missing, loose, crooked or illegible badge
• Signs of denting, scratching or corrosion
• An outdated or inconsistent badge that doesn't match the model

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This 10-32 x 1/4-inch zinc-plated screw secures internal panels and hardware in select dishwashers. Replace a missing, stripped, or corroded fastener to restore a tight fit and help prevent vibration or loosening during operation.

• Fastens brackets, panels, or components that use a 10-32 machine thread
• Replaces hardware that is missing, stripped, or rusted
• Helps reduce rattling or vibration from loose assemblies
• Supports proper component alignment for reliable operation

• Disconnect power and water supply before servicing the appliance
• Remove the old fastener and verify thread size and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace damaged clips, nuts, or inserts that won't hold a 10-32 screw securely