Pdt525ssj0ss Parts

This Silverware Blaster Assembly directs targeted rinse water to the silverware basket so forks, spoons and knives come out cleaner. It replaces a worn or broken blaster to restore focused spray coverage for better wash results. What it does:

• Channels pressurized wash water to the silverware area to improve cleaning of utensils
• Replaces a cracked, clogged, or non-rotating blaster that can leave silverware dirty
• Helps restore normal spray pattern when the original blaster is missing or damaged
• Works with the lower rack silverware basket to target hard-to-reach items

• Disconnect power and shut off water supply before starting any repair
• Remove lower rack to access and remove the old blaster; inspect surrounding clips and seals
• Snap or screw the new assembly into place; ensure it turns freely and is not obstructed
• Run a short rinse cycle to verify proper spray and correct installation

This control box bottom is the lower housing piece that secures and protects the appliance control board and related components. It restores a stable mounting surface and helps keep electronics shielded from vibration and debris. What it does:

• Provides the lower half of the control box housing to support and protect the control board
• Keeps wiring and connectors routed and held in place to prevent strain
• Replaces cracked, broken or warped housing that can expose electronics
• Helps stop rattling or movement of the control assembly that can cause intermittent controls

• Control box bottom

• Power off and unplug the appliance before starting any repair
• Handle the control board and connectors carefully to avoid electrostatic or mechanical damage
• This part typically installs with screws or clips; retain fasteners and note their locations during disassembly
• Inspect and address the electronics before reassembly

This inner door panel replaces the inner-facing panel of the oven door to restore a clean barrier between the oven cavity and the outer door. It helps keep heat inside and protects the outer assembly from spills and grime. What it does:

• Replaces damaged, cracked or heavily stained inner oven door panel
• Restores a proper seal and barrier between the oven cavity and door assembly
• Helps reduce heat loss and prevents food splatter from reaching the outer door
• Matches OEM fit and mounting locations for direct replacement

• One inner door panel

• High-level replacement; remove oven door per manufacturer instructions before disassembly
• Avoid touching glass edges; wear cut-resistant gloves and eye protection
• Keep track of screws and clips during reassembly; use manufacturer torque recommendations

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This manual floor plate is the replacement cover that mounts at the appliance base to protect internal components and provide a finished surface. It restores the dryer's base appearance and helps prevent debris from entering the cabinet. What it does:

• Covers and protects the lower cabinet opening and components from dust and lint
• Helps maintain proper clearance and a finished look at the dryer base
• Replaces damaged, bent, or missing base plates that allow debris entry
• Can reduce rattles or vibration caused by a loose or warped floor plate

• One floor plate

• Disconnect power (and gas, if applicable) before servicing to avoid shock or injury
• Remove the dryer front or lower access panel per manufacturer instructions to access mounting screws
• Use correct-size screws and tighten to manufacturer torque; avoid over-bending the plate during installation

The User Interface Housing is an OEM replacement part for GE dishwashers. Located at the front of the console, it houses the control panel responsible for cycle/option navigation.

The housing protects sensitive electronic components from water damage and physical impact. Its sturdy construction allows for responsive touch inputs without flex or play in the assembly. 

Symptoms of a bad user interface housing include:

• Warping or cracks exposing circuitry to damage
• Faulty sealing allowing moisture penetration
• Difficulty registering button presses from structural defects
• Ill-fitting installation negatively impacting usability

Causes can be repetitive openings allowing entry of dirt/moisture into critical areas and use over the years breaking down seals and weakening materials.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This floor plate is the OEM-style replacement that fits under the oven cavity to protect internal components and provide a stable cooking surface. Restores proper support and helps maintain even heat distribution in the lower oven area. What it does

• Covers and protects the oven's lower cavity from spills, drips, and falling debris
• Helps funnel heat and airflow for more consistent baking and roasting performance
• Prevents direct contact between food/drips and heating components
• Reduces corrosion and wear to inner oven parts caused by spills

• One floor plate as shown

• Designed to be installed in the lower oven cavity; for exact placement
• Remove power (unplug or shut off breaker) and allow the oven to cool before servicing
• Use appropriate gloves to avoid sharp edges; avoid forcing the part into place

This stainless outer door service assembly replaces a damaged or worn outer door panel to restore the appliance's appearance and protective exterior. It provides a finished stainless look and a proper mounting surface for door components. What it does:

• Replaces a dented, scratched, or corroded outer door panel to improve appearance.
• Restores a proper mounting surface for handles, trim, and door hardware.
• Helps protect internal door components from moisture and impacts.
• Can reduce drafts or uneven sealing when a damaged outer door is the cause.

• One stainless outer door service assembly.

• Disconnect power (and water if applicable) before beginning repair.
• Handle the door assembly carefully to avoid injury or damage to the finish.
• Installation typically involves removing door trim/handle and transferring hardware; keep all fasteners and brackets for re-installation.

This block foam door is an insulated panel that fits inside the appliance door to help reduce heat transfer and maintain consistent internal temperatures. It restores door insulation for more efficient cooling and temperature stability. What it does:

• Provides thermal insulation inside the door to reduce heat gain or loss
• Helps prevent frost buildup and cold spots by improving temperature consistency
• Supports efficient compressor cycling and can reduce energy waste when functioning properly
• Common symptom: uneven temperatures, visible condensation or frost on the door, or reduced cooling performance

• One block foam door

• Disconnect power before servicing and follow the appliance manufacturer's disassembly instructions
• May require removing the inner door liner and fasteners to access and replace the foam; keep hardware for reassembly
• Handle carefully to avoid damaging the foam or door liner; use appropriate hand protection

This bracket handle is the replacement mounting bracket that secures a refrigerator or freezer door handle, restoring proper handle alignment and a secure grip. It helps keep the door handle firmly attached and functioning. What it does:

• Secures the door handle to the appliance door so the handle stays mounted and aligned
• Restores a loose, wobbly, or detached handle for reliable opening and closing
• Prevents further wear on handle fasteners by providing the proper mounting support
• Matches OEM fit and function for straightforward replacement

• One replacement bracket handle

• Basic hand tools typically required; handle hardware may need removal first
• Follow OEM instructions and use correct fasteners; replace any damaged screws or anchors
• Disconnect power to the appliance (or keep door open/unloaded) and work safely to avoid pinching or dropping the door

The Screw is an OEM part for GE dishwashers. This screw is designed for various applications, including securing and fastening components in your GE appliance.

A bad screw can result in issues such as loose or unstable components, improper functioning, or even potential damage to other parts. Causes of a bad screw can include wear and tear over time, improper installation, or exposure to extreme conditions.

Symptoms of a bad Screw include:

• Components becoming loose or detached
• Parts not securely fastened
• Unusual noises or vibrations during operation
• Visible signs of damage or wear on the screw

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This transition piece assembly connects the dryer cabinet to the exhaust duct, guiding hot, moist air out of the dryer for proper venting and improved drying performance. It replaces a damaged or worn transition fitting. What it does

• Directs exhaust air from the dryer outlet into the venting system to help prevent backflow and poor airflow
• Helps reduce lint buildup at the cabinet outlet when intact and properly seated
• Restores proper vent path when a cracked, bent, or missing transition causes poor drying or longer cycle times
• Works with standard dryer venting components and clamps to form a secure exhaust connection

• One transition piece assembly

• Disconnect electric power (or shut off gas and unplug for gas dryers) before starting; follow appliance safety procedures
• Inspect the dryer outlet, vent hose, clamps, and adjacent seals; replace any damaged components for a proper seal
• Slide the transition into place and secure with appropriate clamps or screws; ensure the exhaust path is not kinked or crushed
• Check for unrestricted airflow after installation and clean any lint from the vent system

This airbreak flow meter assembly detects water flow and helps the appliance manage fill and dispense cycles for reliable operation. It replaces a failing flow sensor to restore correct water-sensing and cycle control. What it does:

• Measures water flow through the system so the control can confirm proper filling
• Helps prevent overfill or underfill conditions by reporting flow status to the control
• Common symptoms of a failing unit: long or no-fill cycles, water-related error codes, or the appliance not advancing through cycles
• Works as part of the water/ice/fill system to ensure timing and valve operation respond correctly

• Disconnect power and shut off the water supply before starting any repair
• Handle the sensor and electrical connector carefully; avoid pulling on wiring
• Install in the correct orientation and ensure all seals and fittings are seated to prevent leaks
• After installation, restore power/water and run a test cycle to verify proper operation

This silverware basket conduit is the replacement channel that helps secure and guide the dishwasher silverware basket, restoring proper fit and reducing movement during cycles. It brings back stable basket positioning for safer cleaning. What it does:

• Replaces a worn, cracked, or missing conduit that holds or guides the silverware basket
• Prevents the basket from shifting, rattling, or catching on the rack during wash cycles
• Restores correct basket alignment so utensils are held securely for effective cleaning
• Fits and functions as the OEM-designed support channel for the silverware basket assembly

• Disconnect power and water supply before beginning any repair
• Remove the dishwasher rack to access the conduit; handle racks carefully to avoid damage
• Inspect mounting clips or tabs and remove any broken pieces before installing the new conduit

This rail and end cap assembly secures a refrigerator shelf or door bin and restores a stable mounting surface for stored items. It replaces worn or damaged rails that allow shelves to sag or detach. What it does

• Replaces a damaged shelf rail and end cap to restore proper shelf support
• Holds the shelf/bin in position so items stay level and don't slide off
• Stops rattling or movement caused by a loose or broken rail assembly
• Fits where an original molded rail/end cap has cracked, worn, or failed

• One rail and end cap assembly as shown

• Remove food and bins from the area before starting; support the shelf while removing the old part
• Use basic hand tools; avoid forcing parts — align tabs and slide the rail into place until it snaps or seats
• Disconnect power if required by your model before working near electrical components