Pdt525ssj0ss Parts

This upper spray arm gasket seals the hub where the arm connects, keeping wash water routed through the upper arm. Replace a worn seal to restore upper-rack spray performance and reduce internal leaks or water bypass.

• Creates a watertight seal at the upper spray arm connection
• Helps maintain proper water pressure and spray pattern to the upper rack
• Replaces a cracked, flattened, or missing gasket
• Common symptoms: poor upper-rack cleaning, weak/erratic upper spray, dripping at the spray arm hub inside the tub

• Disconnect power and water supply before servicing
• Remove the upper spray arm (and rack if needed) per your model's procedure
• Lift out the old gasket; clean the sealing surfaces; press the new gasket fully and evenly into place
• Reassemble and run a short test cycle to check for proper spray and leaks

The Friction Washer is an OEM component specifically designed for GE dishwashers. This friction washer is a thin circular part that creates resistance through surfaces rubbing together. It is often used beneath a mounting nut to prevent components from loosening during operation.  

Symptoms of a bad friction washer include loose or separating connections where the washer is installed, such as:

• Drain pump mounting fittings that become detached    
• Water connections that leak at the threaded joints
• Door handle mounts that allow play in the mechanism

Causes of failure can be cracks, wear or deformities in the washer that reduce its friction capabilities over time. Vibrations from use may also cause premature wear.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This left-hand attachment strip secures trim and panels for a clean, finished fit on compatible GE appliances. It helps maintain proper alignment and prevents gaps that can collect dirt or allow panels to shift during use. What it does:

• Attaches and stabilizes a side trim or panel to the appliance cabinet
• Keeps door/side trim aligned to reduce rattling or shifting
• Helps maintain an even, finished appearance along the appliance edge
• Addresses symptoms like loose trim, visible gaps, or panel movement

• One left-hand attachment strip

• Remove power to the appliance (or disconnect power source) before starting work
• Use basic hand tools; avoid forcing parts to prevent breakage
• Replace with OEM-specified hardware if fasteners are missing or damaged

This dishwasher hose clamp secures internal hoses to pumps or fittings, helping prevent leaks and disconnections. Replace a weakened or damaged clamp to restore a tight, reliable seal at the connection.

• Provides clamping pressure to hold a hose on pump, sump, or drain fittings
• Helps stop water leaking at hose joints
• Resolves: loose or disconnected hoses, water under the unit/base, or poor draining from a slipped drain hose
• Replaces worn, rusted, or deformed clamps after service

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward as needed for access; place a towel or pan to catch residual water
• Seat the hose fully, then compress or tighten the clamp per its design; position just behind the hose barb bead
• Run a short cycle and inspect for leaks at the connection

This right-hand door hinge arm assembly supports and guides the dishwasher door as it opens and closes. Replacing a bent or worn hinge restores smooth, balanced door motion and helps prevent abrupt, uncontrolled door movement.

• Serves as the right-side pivot for the dishwasher door
• Interfaces with the door spring/link mechanism to counterbalance door weight
• Helps maintain proper door alignment and smooth opening/closing
• Common signs of wear: door drops quickly, feels heavy, binds/creaks, or sits unevenly

• Disconnect power at the breaker before servicing; wear cut-resistant gloves
• Support the door to prevent sudden drop when removing the hinge arm
• The spring/link is under tension—release and reattach carefully
• After installation, check door balance and alignment; adjust spring/link tension if applicable

The Door Arm Hinge Assembly is an OEM component specifically designed for GE dishwashers. It is the mechanism responsible for securing the dishwasher door in place and facilitating smooth opening and closing motions. Reliable door hinges are essential for proper door alignment and a securely closed operation environment during cycles. 

Symptoms of a bad door arm hinge include:

• Squeaks or grinding noises heard from the door area
• Difficulty opening or closing the door  
• Door that does not stay securely shut
• Potential door or door frame damage from loose hinges

Replacement ensures your door operates safely and precisely as intended. Replace yours today with this genuine OEM GE part for trouble-free use.

Note: Left side

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

The Upper Rack Wheel Stud Assembly is an OEM part for GE dishwashers. It is designed to support and secure the upper rack of the dishwasher, allowing for smooth movement during loading and unloading.

A bad Upper Rack Wheel Stud Assembly can lead to issues such as a wobbly or unstable upper rack, difficulty in sliding the rack in and out, or even the complete detachment of the rack. Causes of a bad wheel stud assembly can include wear and tear over time, damage to the stud or wheel due to accidental impacts, or improper installation.

Symptoms of a bad Upper Rack Wheel Stud Assembly include:

• Wobbling or instability of the upper rack
• Difficulty in sliding the rack in and out smoothly
• Excessive noise or grinding sounds when moving the rack
• Inability to properly secure the upper rack in place

Replace your worn-out or damaged Upper Rack Wheel Stud Assembly with this genuine OEM GE part to restore your dishwasher's upper rack. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This Sideblaster inlet restores proper water delivery to the dishwasher's side jets, helping ensure targeted spray along the tub wall. A secure, leak-resistant connection supports consistent cleaning performance on items near the side spray area.

• Feeds water from the circulation system to the side-blaster jets on the tub wall
• Maintains a sealed pass-through to help prevent leaks at the side jet connection
• Helps correct weak/no spray from side jets and poor cleaning near the side of the tub
• Replaces cracked, loose, or damaged inlet fittings that can drip or reduce spray

• Disconnect power and shut off water supply before servicing
• Remove lower rack and panels as needed; you may need to pull the dishwasher out to reach the hose connection
• Transfer and reuse existing clamp/hardware; seat the seal properly and orient the inlet correctly
• Restore water/power and test for leaks and proper side-jet spray before reassembly

This sump latch secures the filter/cover at the bottom of the dishwasher tub, locking the sump assembly in place to maintain proper water circulation and filtration while helping keep debris out of the wash pump.

• Locks the sump/filter cover securely to the tub opening
• Helps maintain consistent water flow and wash performance
• Helps prevent large debris from reaching the pump and spray system
• Typical signs it's worn or broken: cracked/missing latch, filter cover won't stay locked, leaking around the sump area, reduced cleaning results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack (and spray arm/filter as needed) to access the latch
• Release and remove the damaged latch; seat components and lock the new latch securely
• Reassemble and run a brief test to check operation and for leaks

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This coated upper FDT assembly is a direct replacement for the appliance's upper FDT structure, restoring worn or damaged upper components for reliable operation. It helps maintain alignment and reduces wear-related issues. What it does:

• Replaces the appliance's upper FDT assembly to restore proper fit and support.
• Provides the coated surface that helps protect mating parts from wear and abrasion.
• Helps correct symptoms such as rubbing or scraping noises, misalignment of the upper housing, and visible wear or damage.
• Restores the intended clearance and contact surfaces for smoother operation.

• One coated upper FDT assembly.

• Disconnect power to the appliance before starting any repair.
• Handle the coated surfaces with care to avoid scratching or damaging the finish.
• Retain and reuse existing mounting hardware unless replacement hardware is explicitly required.

The Drain Hose is an OEM part for GE dishwashers. It removes wastewater from the dishwasher during each wash cycle.

A bad drain hose can occur due to wear and tear, blockages, or damage from kinks or leaks. If you notice symptoms such as water not draining properly from the dishwasher, leaks around the hose connection, or foul odors coming from the dishwasher, it may be time to replace this part.

Symptoms of a bad drain hose include:

• Improper drainage of water from the dishwasher
• Leaks around the hose connection
• Foul odors coming from the dishwasher

Replace your worn-out or damaged Drain Hose with this genuine OEM GE part to restore your dishwasher. 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This plastic coarse filter traps large food particles and debris in the dishwasher's sump so dishes rinse more effectively and drain paths stay clearer. It's a simple replacement that helps maintain normal wash performance. What it does:

• Captures large food scraps and debris before they reach the pump and drain
• Helps prevent clogging that can cause poor wash results or standing water
• Works with the dishwasher's fine filter and pump assembly to maintain cleaning efficiency
• Reduces the chance of food redeposit on dishes when functioning correctly

• One plastic coarse filter

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove lower dish rack to access the filter area; lift out the old coarse filter and seat the new filter in the sump until it snaps into place
• Inspect and clean the surrounding filter area and fine filter when replacing to ensure a proper seal and performance
• Do not force parts; if the filter does not seat easily, check orientation and debris that may prevent proper installation

This blaster silverware assembly is the dishwasher spray component that directs wash water to the silverware area for better cleaning and rinsing. Replaces a cracked, clogged, or missing blaster to restore targeted spray action. What it does

• Directs high-pressure wash water to the silverware basket for improved cleaning of forks, knives, and spoons
• Replaces a broken, clogged, or leaking blaster that can cause poor silverware cleaning
• Restores proper spray coverage when the original assembly is worn or damaged
• Works with the dishwasher's lower spray system to help remove stuck-on food from utensils

• One blaster silverware assembly

• Disconnect power to the appliance before beginning any work
• Remove the lower rack to access the old assembly; installation typically snaps or screws into the lower spray/silverware area
• Inspect and clear nearby spray arm openings and filter screen of debris while replaced

Replacement silverware basket and snap-on lid for dishwashers. Keeps forks, knives and spoons separated and contained during wash cycles for easier unloading and more consistent cleaning results. What it does:

• Holds and organizes silverware to reduce nesting and improve water circulation for better wash performance.
• Snap-on lid secures utensils so they stay upright and don't fall into spray areas during a cycle.
• Replaces cracked, broken or warped baskets that allow utensils to drop through or shift during washing.
• Common symptom: use when the basket is damaged, the lid won't stay closed, or silverware is not being cleaned consistently.

• Remove the dishwasher's lower rack to access the basket area before installing.
• Slide the basket into the designated position in the lower rack and snap the lid onto the basket until it locks.
• No special tools typically required; handle edges carefully to avoid cuts.
• Disconnect power at the breaker first.