Pdt825ssjoss Parts

This configured machine control board is the electronic brain of your dishwasher. It directs power and timing to pumps, the fill valve, heater, and sensors so cycles start, run, and finish consistently.

• Controls and times each wash cycle
• Sends power to the circulation pump, drain pump, fill valve, and heater
• Interfaces with the user controls; monitors sensors and the door latch
• Failure may cause no power or unresponsive controls
• Can lead to cycles that won't start, stop mid-cycle, or erratic lights/beeping

• Disconnect power at the breaker before servicing; electrical shock hazard
• Use ESD protection and handle the board by its edges
• Photograph/label connections and transfer plugs one at a time until fully seated
• Follow your model's service instructions for any required configuration; reassemble and run a test cycle to verify

This dishwasher fill hose routes incoming water from the inlet valve into the tub. Replacing a brittle or leaking hose helps restore proper filling and reduces the risk of water leaks under the unit.

• Carries fresh water from the inlet valve to the dishwasher during the fill cycle
• Helps maintain correct water level for reliable wash performance
• Common symptoms of a failed hose: leaks near the toe kick, slow fill, or no fill
• Replaces hoses that are cracked, swollen, kinked, or deteriorated

• Disconnect power and shut off the water supply before service
• Place a towel or shallow pan to catch residual water
• Access behind the lower kick panel; transfer existing clamps/fittings as needed
• Route the hose without kinks, fully seat connections, restore water, and check for leaks during a test cycle

This Insulation Bag Assembly is an OEM part for GE dishwashers. It's designed to provide sound insulation and heat retention, enhancing the overall efficiency and noise reduction of the dishwasher. The insulation bag plays a vital role in maintaining the optimal operating temperature within the dishwasher while minimizing the sound during its operation. 

Replacement of the insulation bag assembly may be necessary due to wear, damage, or inefficiency in sound dampening or heat retention. A compromised insulation bag can lead to increased noise levels and reduced energy efficiency.

Symptoms of a malfunctioning Insulation Bag Assembly include:

• Noticeably louder operation of the dishwasher.
• The outer surfaces of the dishwasher becomes unusually warm during operation.
• Physical damage or wear to the insulation material.
• Changes in the dishwasher's drying performance due to altered internal temperatures.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This clamp kit replaces worn Piranha-style clamps used in the dishwasher's wash system. Restores a tight, reliable seal on internal connections to help prevent leaks and maintain proper water circulation for consistent cleaning results.

• Secures internal hose and pump connections within the wash system
• Helps stop water leaks caused by loose, stretched, or damaged clamps
• Supports proper circulation and wash performance by keeping joints sealed
• Common symptoms: water under the unit, drips at hose joints, loose connections, vibration or rattling from the sump area

• Disconnect power and shut off the water supply before servicing
• Access the sump/pump area from the front toe-kick or by pulling the unit out as needed
• Replace one connection at a time; position and fully seat the new clamp(s) on clean hose/barb surfaces
• Restore power/water and run a short cycle to check carefully for leaks before reinstalling panels

This upper wash impeller circulates water to the upper spray system during the wash cycle, helping deliver thorough cleaning across dishes on the upper rack and throughout the tub.

• Drives water flow to the upper spray arm/manifold
• Worn or damaged impeller can cause weak spray, poor cleaning, or longer cycle times
• Physical damage (warping, cracks, stripped splines) warrants replacement

• Disconnect power and water before servicing
• Access is typically through the sump/pump area; note impeller orientation during removal
• Inspect mating parts (seal, hub, shaft/splines) and replace if worn
• Hand-tighten fasteners to OEM guidance and verify free rotation before reassembly

Size: 8-18 AB TSQ 5/8 SS

This is a machine screw used to secure dishwasher components. The 10-32 thread and 3/8-inch length with an integrated hex washer head provide a firm, vibration-resistant hold to keep parts properly fastened.

• Secures brackets, panels, or internal assemblies in the dishwasher
• Helps prevent looseness, rattling, or misalignment during operation
• Common symptoms of a missing/stripped screw include panel movement, vibration, or loose mounting points

• Disconnect power and shut off water before servicing
• Use the correct nut driver or socket to avoid stripping the head
• Replace any damaged or missing screws in matching locations
• Do not overtighten; snug to manufacturer's torque guidance when available

The AC Harness Assembly is an OEM replacement part for GE dishwashers. It is responsible for connecting the dishwasher's electrical system to the power source, ensuring proper functioning and power supply. This part provides a reliable and secure connection between the dishwasher and the electrical outlet. It is designed to deliver consistent and safe power during operation.

Symptoms of a faulty AC harness assembly include:

• Intermittent power loss
• Electrical shorts or sparks
• Dishwasher not turning on or receiving power

A bad AC harness assembly can occur due to wear and tear over time, loose or damaged wiring, or electrical malfunctions. If you experience issues such as intermittent power loss, electrical shorts, or the dishwasher not turning on, it may be time to replace the old or damaged AC harness assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This dishwasher hose clamp secures a hose to its fitting to maintain a tight, leak-resistant seal during operation. Replacing a worn or corroded clamp helps stop drips and keeps fill, drain, or circulation lines firmly in place.

• Secures dishwasher hoses to fittings on pumps, valves, or drain outlets
• Helps prevent water leaks at hose connections
• Keeps hoses from slipping off under vibration and water pressure
• Typical symptoms include water under the unit, dampness in the cabinet, or a hose connection that feels loose

• Disconnect power and shut off water supply before servicing
• Access the hose connection (toe-kick or rear/side panels may need removal)
• Seat the hose fully on the fitting, position clamp just behind the barb/ridge, and secure without over-tightening
• Run a short test cycle and check all connections for leaks

This side blaster assembly mounts to the dishwasher's tub wall and directs a focused spray into the wash cavity to help scour stuck-on residue. Replace if the nozzle is cracked, clogged, or leaking to restore proper cleaning performance.

• Provides targeted side-wall spray to supplement the main wash arms
• Helps flush debris and improve coverage along racks and corners
• Common failure signs: weak or no side spray, poor cleaning near the side wall, visible cracks, or leaks at the side jet
• Restores intended spray pattern and water distribution when the original is damaged or blocked

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack to access the side blaster location
• Release the retainer/screw, disconnect the hose/tube, and install the new assembly; ensure the sealing surface is clean and properly seated
• Reconnect, secure, and run a test cycle to check for leaks and proper spray

This replacement flood stem holds and guides the washer's water-level float so the machine can detect and control water levels. Replaces a worn or damaged mounting tube to restore reliable float operation. What it does:

• Secures and positions the water-level float inside the tub or housing
• Allows the float to move freely so the machine senses proper water level
• Helps prevent overfill and incorrect fill-level behavior when functioning correctly
• Common symptoms of a faulty unit: incorrect water level, washer overfills or fills unevenly, or the machine shows fill/drain issues

• One flood stem

• Disconnect power and turn off the water supply before starting any repair
• Replacement typically requires access to the washer cabinet/top or inner tub area
• Handle the float and tube gently to avoid damage; ensure proper seating and alignment during reassembly
• After installation, run a short fill/drain cycle to confirm correct float operation and that there are no leaks

Keep your dishwasher draining properly. This drain hose kit channels wastewater from the tub to your household drain, replacing a cracked, kinked, or leaking hose to help prevent leaks, odors, and standing water at the end of the cycle.

• Carries discharge water from the dishwasher to the sink drain or disposer
• Helps prevent backflow when routed with a proper high loop or air gap
• Replace if the hose is brittle, split, kinked, or clogged
• Common symptoms: standing water after a cycle, slow/no drain, leaks under the sink or at the base

• Disconnect power and turn off water; place a towel to catch residual water
• Access the hose connections at the pump and at the sink/disposer/air gap
• Route the new hose with a high loop or to an air gap per local code; avoid sharp bends and kinks
• Secure all connections with clamps and run a short cycle to check for leaks

The Upper Rack Bracket Assembly is an OEM replacement part for  GE dishwashers. It is located inside the dishwasher tub and functions to securely mount the upper dish rack. It allows for adjustable height positioning and prevents rack movement during washing.

Causes of a bad upper rack bracket assembly can include cracks or breaks in the mounting points, stripped screw holes allowing rack sway, or deformities preventing proper seating.

Symptoms of a bad upper rack bracket assembly include: 

• Loosening or detaching of the upper rack during the cycle  
• Restricted rack adjustment or inability to set desired height
• Noise or vibration from an unsecured rack vibrating against the tub

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Conduit Main Assembly is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper wash arm, and is responsible for securely mounting and holding the upper wash arm in place during operation.  

Causes of a bad upper wash arm support include:

• Symptoms of a bad upper wash arm support include: 
• Vibration or noise from an unsecured wash arm
• Improper alignment of spray pattern
• Restricted rotation of the wash arm during washing  
• Leaks at the tub connection point

Symptoms can include cracks or breaks that compromise its structure, or wear over extended use without replacement.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This insulation bag assembly installs around the dishwasher tub to dampen operating noise and limit heat transfer. Replace when the original insulation is missing, damaged, or saturated to help maintain quieter cycles and protect nearby cabinetry. What it does:

• Provides an acoustic and thermal barrier along the tub exterior
• Helps reduce cycle noise and vibration
• Helps minimize heat and moisture reaching surrounding cabinets
• Replacement may help with louder operation, warm exterior panels, or increased condensation

• 1 insulation bag assembly

• Disconnect power at the breaker and shut off the water supply; remove toe panel and slide the dishwasher out for access
• Wear gloves/long sleeves when handling insulation
• Position in the factory location without pinching wiring or blocking vents, door seals, or moving parts
• Reinstall panels, level the unit, restore power/water, and run a test cycle to verify proper operation and no leaks

This is a 6-20 machine screw, 3/8 inch length, used to secure trim, panels, or small components on compatible cooking appliances. Replacing a missing or damaged screw helps keep parts tight and prevents rattles or shifting during use.

• Fastens brackets, panels, or trim in the appliance chassis
• Helps restore a secure fit when the original screw is stripped or lost
• Can resolve issues like loose trim, minor rattling, or misaligned panels
• Nickel finish for corrosion resistance in warm, humid environments

• Disconnect power and allow appliance to cool before servicing
• Remove only the necessary adjacent fasteners to access the mounting point
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any missing clips or spacers originally used with the screw