Pdw 9280Looss Parts

This dishwasher float sits in the tub and works with the float switch to control the fill level and prevent overfilling. Replace it if cracked or sticking to restore reliable water level control and help avoid leaks.

• Rises with the water level to trigger the float switch and stop filling at the correct point
• Helps prevent overfilling and door leaks
• Common symptoms of a damaged or obstructed float include continuous filling, overfill/leaks, or no/insufficient fill
• Restores consistent water level sensing when the original float is worn or missing

• Disconnect power and turn off the water supply
• Open the door and remove the lower rack
• Remove the float cover; pull the old float straight up and clear any debris from the well
• Insert the new float and verify free up-and-down movement before reassembly and testing

This fill funnel gasket seals the water-inlet funnel where water enters the dishwasher tub. Replacing a worn seal helps prevent drips at the inlet and keeps incoming water directed into the tub during the fill cycle.

• Provides a watertight seal between the fill funnel and tub wall
• Helps prevent leaks from the inlet area and under the toe-kick
• Directs incoming water properly into the tub during fill
• Replace if the gasket is cracked, deformed, or leaking

• Disconnect power and turn off the water supply before servicing
• Access the fill funnel area; remove the old gasket and clean the sealing surfaces
• Seat the new gasket evenly and ensure the funnel fully engages the opening
• Reassemble and run a short fill to check for leaks

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This pump hose and clamps create a sealed connection between the dishwasher's pump and internal plumbing. Replace when the hose is cracked or clamps are corroded/loose to stop leaks and restore a secure, watertight fit. What it does:

• Creates a sealed connection between the pump and internal plumbing
• Helps contain water flow during wash and drain operation
• Replace if the hose is cracked, brittle, swollen, or deformed
• Symptoms include water leaking under the dishwasher or loose/corroded clamps

• Disconnect power and water; pull the dishwasher forward as needed for access
• Expect residual water—protect flooring and have a towel or pan ready
• Remove old clamps and hose; fully seat the new hose on fittings, then position and secure clamps at the bead/ridge
• Run a brief cycle and check for leaks before reinstalling

The Spray Arm Connector Assembly is an OEM replacement part for GE dishwashers. This assembly connects the upper and lower spray arms to the water inlet valve, allowing water to flow through the spray arms during the wash cycle. 

Symptoms of a bad spray arm connector assembly include: 

• Uneven or inconsistent water coverage on dishes
• Clogged or kinked spray arm assemblies 
• Leaks at the tub connections
• Reduced water pressure impact 

Causes of a bad spray arm connector assembly can be mineral buildup affecting water flow, cracked or damaged connectors, or wear over time.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This overload relay protects and helps start the refrigerator/freezer compressor by cutting power if the motor overheats or draws excessive current. Replaces a failed relay to restore normal compressor start and protect the compressor from damage. What it does:

• Senses excessive compressor current or heat and interrupts power to prevent motor damage
• Works with the compressor start device to help the compressor start reliably
• Commonly replaces a failed relay when the compressor hums but won't start or the refrigerator is not cooling
• Helps prevent repeated compressor attempts that can trip breakers or overheat wiring

• Disconnect power to the appliance before accessing electrical components
• Handle terminals carefully; ensure correct seating on the compressor motor pins
• Only install parts that match the appliance's service literature and wiring configuration

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This gripper holds stemware securely in the dishwasher stemware rack to help prevent glasses from tipping, shifting, or breaking during a wash cycle. It replaces worn or broken stemware clips so racks can secure the stems of wine and other stemmed glasses. What it does:

• Clips onto the dishwasher stemware rack to hold glass stems steady during cycles
• Helps reduce glass-to-glass contact and chipping from shifting items
• Restores proper rack functionality when original grippers are missing or damaged
• Fits into the rack's designated stemware openings for a snug hold

• One gripper stemware clip (single piece)

• High-level replacement — typically snaps into the rack's stemware slot without tools
• Inspect the rack for damage; replace any additional broken clips as needed
• Disconnect power to the appliance before doing any work that requires access inside the dishwasher
• Handle glass carefully to avoid breakage during removal and reinstallation

This replacement multi-purpose glass shelf provides a sturdy, easy-to-clean surface for organizing food and containers in your refrigerator. Restores usable shelving space after a chip, crack, or missing shelf. What it does:

• Supports refrigerated items and helps keep food organized and visible
• Replaces a cracked, chipped, broken, or missing refrigerator shelf
• Fits into existing shelf tracks or ledges to restore proper shelf spacing
• Tempered glass construction resists everyday cold-area wear (handle with care)

• Remove food and containers from the area before installing
• Handle the shelf carefully; wear cut-resistant gloves if replacing a broken shelf
• Slide shelf into the existing tracks/ledges until fully seated; do not force
• If glass is damaged on arrival, stop installation and contact the seller for a replacement