Pfe28ksknss Parts

Includes 12 screws.

This SCR (silicon controlled rectifier) controls high-current switching in the appliance's power circuit to enable reliable on/off control of heating or motor circuits. Designed for direct replacement of the original SCR component. What it does:

• Acts as a solid-state switch to control power to heating elements or motors when triggered by the appliance control board.
• Helps regulate current during start-up and run cycles to maintain proper operation of the appliance.
• Failures can cause symptoms such as no heat, intermittent operation, or the appliance not powering its load.
• Matches the OEM mounting and stud terminal configuration for proper electrical connection.

• One SCR component (8-32 stud) as pictured.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Use proper tools for the 8-32 stud terminals and ensure secure electrical and heatsink connections.
• Inspect mounting surfaces and replace any damaged hardware or thermal pads as needed for safe operation.

A replacement 8-18 x 3/4 flanged pan-head screw used to secure panels, trim, and components. Restores proper fit and stops loose parts from rattling or shifting, helping appliances operate quietly and safely. What it does

• Fastens panels, brackets, trim pieces or assemblies that use an 8-18 thread screw
• Replaces missing or stripped screws that cause loose or vibrating parts
• Helps maintain proper alignment of panels and covers
• Prevents gaps that can allow movement or noise during operation

• One 8-18 x 3/4 flanged pan-head screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread the screw in by hand first, then snug; avoid over-tightening
• If underlying threads are damaged, replace the mating fastener or insert as needed

This compressor mounting stud secures the compressor to the refrigerator chassis, keeping the unit stable and reducing vibration and noise. It's a durable replacement part for worn, bent, or missing compressor mounting hardware. What it does:

• Provides a secure attachment point between the compressor and cabinet/frame
• Helps reduce compressor vibration and operational noise when correctly installed
• Prevents compressor movement that can stress refrigerant lines or electrical connections
• Commonly replaced when the original stud is corroded, damaged, or missing

• Disconnect power to the appliance before beginning any repair.
• Support the compressor while removing/installing mounting hardware to avoid strain on lines and fittings.
• Replace any associated nuts, washers, or insulators if worn or damaged; use correct hardware orientation.

This 10-32 hex washer head screw secures panels and components on appliances, providing a reliable fastener that helps keep parts aligned and vibration-free. Use it when a matching machine screw is missing or damaged. What it does

• Fastens appliance panels, brackets, and small components using a 10-32 machine thread
• Hex washer head spreads load and resists pull-through on thin sheet metal
• Replaces missing or stripped screws that cause loose panels, rattling, or misaligned parts
• Compact size for tight mounting locations where a machine screw is required

• One 10-32 hex washer head screw, 1/2 inch length

• Disconnect power and follow appliance safety procedures before servicing
• Use the correct 10-32 driver (hex/Socket or nut driver) to avoid stripping the head
• Tighten snugly but avoid over-torquing to prevent thread damage or panel distortion
• Replace with identical size and thread to ensure proper fit and function

This condenser support is the replacement mounting bracket that holds the refrigerator condenser or condenser coil securely in place, helping maintain proper clearance and airflow for reliable cooling performance. What it does:

• Secures the condenser or condenser coil to the cabinet to prevent movement or vibration
• Maintains correct condenser positioning to support consistent airflow and heat dissipation
• Helps reduce rattling or noise caused by a loose condenser assembly
• Supports overall cooling reliability by keeping components aligned

• One condenser support bracket

• Installation requires basic hand tools; disconnect power before beginning any repair
• Handle sharp sheet-metal edges carefully to avoid cuts
• Reinstall any removed panels or fasteners to restore proper airflow paths

This rubber grommet cushions and protects small appliance wires, hoses, or components where they pass through panels or openings. It helps prevent chafing and vibration wear for quieter, longer-lasting operation. What it does:

• Cushions wiring or tubing where it passes through sheet metal to prevent rubbing and damage
• Reduces vibration noise from loose fittings or contact points
• Holds harnesses or hoses in position to maintain proper routing
• Helps keep openings sealed against dust and debris around routed components

• Disconnect appliance power (and water if applicable) before replacing parts
• Remove the original grommet and install the new grommet in the same orientation; ensure the wire/hose seats fully in the grommet
• Inspect surrounding wiring, hoses, and mounting holes for damage and replace if needed
• Use only the specified replacement grommet; do not modify with adhesives or solvents unless manufacturer guidance allows

This center track screw cover caps the exposed screw on the center track assembly to protect the screw head and give the track a finished appearance. It helps reduce debris buildup and prevents accidental snags on the screw head. What it does:

• Covers and protects the center track screw head from dirt, moisture, and surface wear
• Helps maintain a smooth surface on the track to reduce snagging or catching
• Restores the OEM appearance where the original cap is missing or damaged
• Small replacement part used with center track assemblies and trim pieces

• One center track screw cover (cap)

• Designed for simple push- or snap-fit installation over the exposed screw head
• Remove power to the appliance before accessing internal trim or track areas, and follow manufacturer safety guidance
• If screw or track is damaged, inspect and replace the underlying hardware before installing the cap
• Handle small parts carefully to avoid loss during installation

The Front/Rear Wheel & Axle is an OEM replacement part for GE refrigerators. This set includes both the front and rear wheels, along with the axle, providing a solution for movement of your refrigerator. These wheels and axle ensure easy mobility and stability when moving or repositioning your refrigerator. The front wheels allow for convenient maneuverability, while the rear wheels provide stability and support.

A bad front/rear wheel and axle can occur due to wear and tear, damage, or component failure over time. If you notice symptoms such as difficulty in moving the refrigerator, uneven or wobbly positioning, or unusual noises when the refrigerator is being moved, it may indicate a need to replace the front/rear wheel and axle.

Symptoms of a bad front/rear wheel and axle include:

• Difficulty in moving the refrigerator
• Uneven or wobbly positioning
• Unusual noises when moving the refrigerator

Restore your refrigerator by replacing the faulty front/rear wheel and axle with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.