Phe 60 -Thermador Parts

The MWF Bypass is an OEM replacement part for GE refrigerators. Located within the bottom freezer compartment, the metal water filter bypass fitted assembly is responsible for directing filtered or unfiltered water flow to the ice maker and dispenser.

Causes for replacement may include faulty diverter components obstructing water flow to selections or resulting in water leaks.

Symptoms of a problematic bypass unit include:

• Inability to select filtered or unfiltered water from the dispenser
• Ice maker failure due to lack of water or poor water quality
• Mineral deposits accumulating on internal parts from unfiltered water

This OEM replacement bypass is compatible with GE, Hotpoint, and Profile model refrigerators.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

This low-voltage transformer wire harness routes the 42/48V control power between the appliance transformer and control components, restoring reliable low-voltage connections for proper control operation. What it does:

• Carries low-voltage (transformer) control signals between the transformer and control board/components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent or no control response
• Helps restore consistent control panel and relay operation when harness failure is the cause
• Used where a dedicated 42/48 transformer wiring harness is specified

• One replacement low-voltage transformer wire harness (42/48)

• Disconnect power before accessing internal components to avoid electrical shock or damage
• Inspect connectors and mating terminals for corrosion; replace or clean if needed before installing new harness
• Route harness following original wire paths and secure with existing clips to prevent chafing

This union connector joins two sections of appliance water tubing to maintain a watertight supply line for icemakers or dispensers. It's a direct replacement piece that helps stop leaks and restore proper water flow. What it does

• Connects two water tubing segments to create a sealed junction for appliance water supply lines
• Stops leaks or drips at a damaged or corroded tubing connection
• Restores proper water flow to icemakers, dispensers, or other water-fed components
• Compatible with standard appliance water tubing sizes where this OEM connector is specified

• Turn off the appliance water supply (and unplug appliance if advised) before beginning work
• Remove the damaged connector and clean tubing ends before installing the new union
• Hand-start fittings, then tighten securely; check for leaks with the water supply back on

This AHU Chill seal is a replacement gasket designed to help maintain proper temperature control and airflow in the chilled compartment. It restores a tight seal to reduce warm-air leaks and help the appliance run more efficiently. What it does:

• Replaces a worn or damaged chill compartment gasket to restore an airtight seal
• Reduces warm air infiltration that can cause frosting or inconsistent temperatures
• Helps the cooling system maintain set temperatures and reduces run time caused by leaks
• Fits where the AHU/chill compartment requires a dedicated perimeter seal

• One AHU Chill seal (gasket) as shown

• Remove old gasket and clean mating surfaces before installing the new seal
• Press the gasket into the channel evenly; avoid stretching or twisting the seal
• Check the seal for uniform contact and adjust as needed; replace damaged retainers if present

This wire Wine & Beverage Rack replaces a damaged or missing shelf in wine and beverage refrigerators to securely hold bottles and maximize usable storage space. It restores proper bottle support and prevents shifting during use. What it does:

• Provides stable support for wine and beverage bottles so they store evenly and don't roll or tip.
• Restores proper spacing and organization inside the cooler or wine compartment.
• Helps prevent contact between bottles and interior surfaces that can cause chips or scratches.
• Fits into the cabinet's existing rails or brackets to recreate the original storage layout.

• One replacement wire wine & beverage rack

• Unplug the appliance or switch off power before reaching into the compartment.
• Slide the rack into the existing rails or brackets; no special tools usually required.
• Handle edges carefully; avoid forcing the rack into position to prevent damage.
• If original rails or clips are damaged, inspect and replace those mounting parts separately.