Plhs269zdb6 Parts

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This ice cream shelf rail guides and secures the freezer's ice cream shelf so tubs stay level and accessible. It restores proper shelf alignment and prevents sliding or rattling of the ice cream compartment shelf. What it does:

• Holds the ice cream shelf in place so frozen goods stay stable during door movement
• Guides shelf slides to keep the shelf aligned and prevent binding
• Reduces shelf rattling and noise from the ice cream compartment
• Helps restore proper shelf seating after a broken or worn rail

• High-level replacement; remove shelf and slide to access rail mounting points
• Use common hand tools; support shelf while loosening or tightening fasteners
• Disconnect power only if working near electrical components; exercise caution with sharp edges
• If screws or clips are missing or damaged, replace them before final reassembly

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

This control front box is the outer housing that holds and protects the oven or range control assembly and user interface, keeping components aligned and secure for reliable operation. It restores proper mounting and appearance of the control area. What it does:

• Provides a sturdy mounting enclosure for the control board, switches and display
• Protects electronics from heat, grease and accidental contact
• Keeps buttons, dials and the user interface properly positioned for accurate operation
• Can stop symptoms like a loose or misaligned control panel, exposed electronics, or intermittent button contact

• One control front box (housing) as pictured

• High-level replacement of the front housing may require removal of the cooktop or control panel
• Disconnect power (unplug or shut off breaker) before starting to avoid shock or injury
• Handle the control board and ribbon cables carefully to avoid damage from static or bending
• Use existing fasteners or OEM replacement screws;

Color: Black/natural. Nylon

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

Right hand side. For the left hand side order 241674401