Psa9240 Parts

This replacement blower fan mounts on the blower motor to move air through the appliance's ventilation path and cool internal components. It restores proper airflow to help clear steam/smoke and reduce noise from a cracked or warped wheel. What it does:

• Couples to the blower motor to push/pull air through the exhaust or recirculation ducts
• Helps cool internal parts while venting cooking steam and odors
• Typical failure signs: scraping/rattling noises, reduced or no airflow, poor venting performance, or intermittent overheating shutdown

• 1 blower fan wheel

• Disconnect power at the breaker or unplug before servicing
• If over-the-range or built-in, support the unit and follow manufacturer procedures to access the blower housing
• Match the original wheel orientation and seat fully onto the motor shaft
• Spin by hand to ensure free rotation and clearance; reassemble and test all fan speeds

A temperature sensor assembly that monitors internal temperatures and sends readings to the appliance control so the unit can maintain proper heating or cooling. Replacing a failed sensor restores accurate temperature regulation and consistent performance. What it does

• Detects and reports temperature to the electronic control or thermostat
• Helps the appliance maintain set temperatures for consistent operation
• A faulty sensor can cause inaccurate temperature readings or uneven heating/cooling
• May trigger temperature-related error codes or put the unit into a diagnostic/fail-safe mode

• Disconnect power to the appliance before attempting any repair
• Handle the sensor and its wiring gently; avoid bending or damaging the sensing tip or connectors
• Reconnect wiring securely and confirm correct routing to prevent interference with moving parts

This ring assembly replaces a worn or damaged trim ring to restore proper fit and finish on your appliance. It helps secure surrounding components and reduces vibration or misalignment for smoother operation. What it does

• Acts as the trim/mounting ring that holds or aligns adjoining parts in place
• Restores proper fit and reduces rattling or loose gaps around the opening
• Helps prevent misalignment-related wear on adjacent components
• Common symptom: visible gap, loose trim, or vibration/noise during operation

• One ring assembly

• Disconnect power to the appliance before starting any repair
• Use basic hand tools; refer to the appliance's parts diagram for exact placement
• Handle mounting surfaces and adjacent trim carefully to avoid scratching or bending
• Reinstall components in reverse order and verify proper fit before restoring power

This micro switch is a small electromechanical door/control switch that restores reliable on/off signaling for your appliance. Replacing a failed switch helps restore normal operation and safety interlocks. What it does:

• Opens or closes an electrical circuit when actuated, enabling controls or motors to run
• Commonly used in door and safety interlock applications to prevent operation when open
• Can stop intermittent power or control-response problems caused by a worn switch
• Helps resolve symptoms like appliance not starting, controls not responding, or cycling unexpectedly

• One micro switch

• Disconnect power (unplug appliance or flip the breaker) before servicing
• Observe sharp edges and wear protective gloves; remove access panels as needed
• Verify correct switch orientation and actuator engagement before reassembly
• Test continuity with a multimeter after installation to ensure proper operation

This suction guide positions and supports the appliance's suction component to help ensure proper fit and reliable operation. Replacing a damaged guide restores alignment so the suction assembly can work as intended. What it does:

• Holds and guides the suction component or cup into the correct position
• Prevents misalignment that can cause vibration, rubbing, or reduced suction performance
• Helps maintain a consistent seal where the suction component interfaces with the appliance
• Useful when the original guide is cracked, broken, or worn

• Disconnect power (and water, if applicable) before servicing the appliance
• Access may require removing an outer cover or access panel and a few fasteners
• Handle plastic parts carefully to avoid cracking during removal and installation

This safety cover protects internal wiring and components by enclosing delicate parts and helping prevent accidental contact. It restores a safe barrier and helps avoid shorting or debris buildup in the affected area. What it does

• Covers and protects wiring, connectors and nearby components from contact and debris
• Helps prevent accidental electrical contact and reduces risk of shorts where the cover is installed
• Commonly replaced when the original cover is cracked, melted, broken or missing
• Helps restore proper component spacing and secure mounting of nearby parts

• One safety cover

• Disconnect power to the appliance before servicing; verify it cannot be energized
• Remove panels or trim as needed to access the cover; keep fasteners for reinstallation
• Align mounting tabs or screw holes and secure with the original hardware
• If wiring or components show damage, replace or repair those items before reinstalling the cover

This AC fan motor is the refrigerator fan motor that circulates air to maintain proper cooling and airflow. It replaces a worn or failed fan motor to help restore steady airflow and consistent temperatures. What it does:

• Spins the evaporator/condenser fan blade to move air through the refrigerator cooling system
• Restores airflow when fan has stopped running or runs intermittently
• Reduces unusual fan noise or vibration caused by a failing motor
• Helps correct uneven cooling or frost build-up linked to poor air circulation

• Disconnect power to the appliance before starting any work
• Handle the fan blades carefully to avoid bending or injury
• Verify fan blade seating and clearances during reassembly to prevent rubbing

This replacement control knob restores a secure, accurate feel when selecting settings on your appliance. Swap in a new knob to fix cracked, stripped, or missing originals so you can turn the control reliably and keep daily cooking on track.

• Engages the control shaft so you can select heat or function as intended
• Common symptoms: knob spins freely, falls off, feels wobbly, or won't turn the control
• Restores proper indexing with panel markings for predictable operation
• Freshens the look of a worn or damaged control area

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft—avoid prying against the control panel
• Align the new knob with the flat/key on the shaft and press firmly until fully seated
• Verify smooth rotation and correct pointer alignment after installation

A replacement relay board that restores the control relay functions used to switch high-current components in the appliance. Installs behind the control panel to help re-establish reliable electrical switching and operation. What it does:

• Acts as a switching module that delivers power to high-current components when commanded by the main control
• Common symptom: appliance components fail to run or intermittently stop despite proper control signals
• Common symptom: clicking or buzzing from the control area when a component tries to start
• Helps correct failures caused by burned or stuck relay contacts that prevent power delivery

• Disconnect power to the appliance before inspecting or replacing the board
• Handle the board by its edges and avoid touching circuitry to reduce ESD risk
• Verify mounting orientation and connector seating; ensure all wiring harnesses are fully engaged

This nut assembly secures an appliance component to its mounting point, restoring a solid connection and preventing unwanted movement. Replace a damaged or missing nut to stop rattling and keep parts aligned for reliable operation. What it does:

• Fastens a panel, bracket or component to its mounting stud or bolt to maintain proper alignment.
• Restores a secure connection when the original nut is stripped, corroded or missing.
• Helps stop rattling, looseness or parts that won't stay in place.
• Works as a direct replacement to restore proper fit and function.

• Disconnect power (and water if applicable) before beginning any repair.
• Use the correct-size socket or wrench; avoid cross-threading when installing.
• Tighten snugly but do not overtighten — replace mating hardware if threads are damaged.

This circulation motor powers air movement inside the appliance to maintain proper airflow and even temperatures. Replacing a failed motor restores circulation for more consistent cooling and reduces noise or performance issues. What it does:

• Spins the fan to circulate air through the cooling/ventilation path
• Helps maintain even temperatures and proper airflow in the appliance
• Commonly replaced when airflow is weak, cooling is uneven, or the motor is noisy
• Stops operation if the motor fails, which can lead to frost buildup or reduced performance

• Disconnect power to the appliance before starting any repair
• Access and mounting steps vary by model; follow the appliance's service manual or wiring diagram
• Handle wiring connectors carefully and confirm proper fan rotation before reassembly

This is a truss-head self-tapping screw used to secure appliance panels and trim. It replaces a lost or damaged mounting screw to restore proper fit and stop rattles or loose parts. What it does

• Secures trim, panels, brackets or small components where a low-profile, wide-head screw is required
• Self-tapping design cuts threads into sheet metal or similar substrates—no nut required
• Restores tight mounting to reduce vibration, rattling or misaligned panels
• Commonly used in refrigerators, ranges and other household appliances

• One truss-head self-tapping screw

• Disconnect power to the appliance before servicing and work on a cool appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten—turn until snug and the part is secure but not distorted
• Replace with the exact part number to ensure fit and function

This main control board is the appliance's electronic control module that manages user inputs, cycles, and functions for compatible GE appliances. Replacing a faulty board restores control panel responsiveness and correct operation. What it does:

• Receives signals from the control panel and sends commands to motors, valves, heaters, and sensors
• Can stop the appliance from powering on or responding to inputs when failed
• May cause display errors, random cycles, or loss of certain functions
• Restores normal electronic control when the board is the confirmed failure

• Disconnect power before starting and verify the appliance is de-energized
• Handle the board carefully and avoid touching circuit traces or contacts
• Note connector locations and take photos before removal for correct reassembly

This heater sheath is the protective metal sleeve that surrounds a dryer/oven heating element, helping protect the element and focus heat where needed for reliable appliance heating performance. What it does:

• Protects and supports the heating element inside the appliance
• Helps direct and contain heat for efficient operation
• Can prevent direct contact between the element and surrounding components
• Commonly replaced when the sheath is corroded, dented, or damaged
• Linked to uneven heating or visible element damage

• High-level replacement only; disconnect power before servicing to avoid shock hazard
• Inspect surrounding components (element, terminals, mounting clips) and replace any damaged parts
• Use proper fasteners and ensure sheath is seated securely to avoid contact with other components

This nonstick tray-grille pan is the oven broiler pan used to catch drippings and hold food for broiling, grilling and roasting. The durable nonstick finish helps reduce sticking and makes cleanup easier. What it does:

• Holds food during broiling and grilling to promote even exposure to heat
• Catches grease and drippings to help reduce smoke and oven mess
• Designed to work with the oven's broiler system for high-heat cooking tasks
• Nonstick surface helps prevent food from adhering and simplifies cleanup

• One nonstick tray-grille pan

• Make sure the oven is completely cool and power is off before handling or installing parts
• Slide the pan onto the broiler support or oven rack in the same orientation as the original part
• Use oven mitts or gloves when removing the pan after cooking; let it cool before cleaning
• Clean with a soft sponge and mild detergent to preserve the nonstick finish; avoid abrasive pads