Pss23mgta Bb Parts

This bottom hinge and pin assembly secures and supports the lower refrigerator/freezer door, allowing smooth pivoting and proper alignment for reliable opening and closing. It replaces a worn or bent hinge to restore door stability. What it does:

• Provides a stable pivot point for the lower door to ensure correct alignment and smooth operation
• Helps prevent door sagging, rubbing, or misalignment that can cause poor sealing or uneven gaps
• Fits the lower hinge location and transfers door weight to the cabinet frame
• Works with existing hinge housing and mounting points to restore factory movement

• Turn off power to the appliance and remove all items from the door before starting
• Support the door securely while removing and installing the hinge to avoid injury or damage
• Use appropriate hand tools; tighten fasteners to secure but avoid over-torquing

This light bezel is the trim piece that surrounds and secures the refrigerator/freezer interior lamp, providing a finished appearance and helping keep the lamp in place. It restores a clean fit and prevents light lens movement. What it does:

• Holds the interior lamp assembly or lens in position and covers the lamp opening
• Replaces cracked, broken, or warped trim that lets the lens rattle or sit unevenly
• Helps maintain a sealed appearance around the lamp to reduce light glare and gaps
• Compatible with appliances that use the matching OEM bezel design

• Disconnect power to the appliance before starting any work to avoid shock
• Handle the bezel and lamp lens carefully to avoid cracking; use appropriate tools for retaining clips or screws
• If replacing the lamp or lens, confirm bulb type separately
• Reassemble in reverse order and test the lamp for proper fit and operation after installation

This silicon controlled rectifier (SCR) is a replacement control semiconductor that helps regulate power to heating elements and motors, restoring proper cycle control and heat delivery in compatible appliances. What it does:

• Controls and chops AC power to heating elements or motor circuits for variable heat/speed control
• Can stop intermittent or no-heat conditions caused by a failed SCR in oven, range, or similar appliances
• Helps restore stable thermostat/regulation behavior when the original SCR is not switching correctly
• Commonly used where precise power control is required in the appliance's control board or module

• One silicon controlled rectifier (SCR) as shown

• High-level, service-only replacement — disconnect power before starting work
• Verify correct part number on the appliance and transfer heat sinks or mounting hardware if required
• Use proper ESD precautions when handling semiconductor components

This replacement cover hinge secures and supports the appliance access cover, restoring proper alignment and smooth opening/closing. It's a direct-fit part that helps stop sagging or loose covers and reduces rattling during operation. What it does:

• Replaces a worn or broken cover hinge to restore proper cover alignment and operation
• Helps stop cover sagging, uneven gaps, or covers that won't stay closed
• Reduces rattling or vibration caused by a loose hinge
• Matches white trim for a clean, factory appearance

• High-level fit: installs at the cover mounting point using the factory screws or clips
• Safety first: disconnect power to the appliance before beginning any repair
• Handle trim pieces carefully to avoid scratching or cracking during removal/installation

This bottom door hinge secures the refrigerator/freezer door at the lower pivot and helps ensure smooth, stable opening and closing. Durable replacement that restores proper door alignment and keeps the seal functioning. What it does:

• Supports the bottom of the door and serves as the lower pivot point
• Keeps the door aligned so it closes fully and maintains a proper seal
• Reduces door sag, rubbing, or uneven gaps that cause cooling issues
• Fits and functions as the factory replacement hinge for compatible GE units

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use appropriate hand tools; avoid overtightening fasteners which can misalign the door

This mullion duct gasket seals the vertical door/mullion area to help keep cold air inside the refrigerator and reduce condensation. It replaces a worn or damaged gasket to improve seal performance and reduce moisture buildup. What it does:

• Seals the mullion/duct area between doors to help maintain proper temperature and reduce warm air infiltration
• Helps prevent condensation and frost build-up along the door mullion
• Restores the door seal where gaps or deterioration allow air leaks
• Works with original mullion/duct trim to maintain proper airflow paths

• 1 mullion duct gasket

• Designed to fit into the mullion/duct channel; remove old gasket and press new gasket into place
• Handle gently to avoid stretching or tearing the gasket during installation
• Clean the mounting channel before installing to ensure a full contact seal
• Disconnect power or follow appliance safety guidelines before servicing doors/mullion area

A right-hand slide basket that restores smooth support and guided movement for a refrigerator drawer. Replaces a damaged or worn slide assembly so the basket stays aligned and operates without binding. What it does

• Provides the right-side sliding support for a refrigerator shelf/drawer, keeping the drawer aligned as it opens and closes
• Replaces broken, bent, or worn slide hardware that causes scraping, binding, or a drawer that falls out of track
• Helps restore smooth travel and load-bearing for everyday use
• Fits into factory mounting points and works with the factory left/right counterpart when both are present

• One right-hand slide basket assembly

• Disconnect power to the appliance or unplug the refrigerator before starting service to avoid electrical hazard
• Empty the drawer and remove adjacent shelves or trim to access mounting points as needed
• Use basic hand tools; support the drawer while removing and installing the slide to prevent drops or damage

This is a mobility screw used to secure mobility-related components in compatible appliances, providing a reliable fastener for stable operation and correct alignment. It replaces worn or missing screws to restore secure mounting. What it does

• Fastens and secures mobility/bracket components to prevent movement or misalignment.
• Helps maintain proper alignment of moving parts that can cause noise or binding when loose.
• Commonly replaced when mounting points are stripped, damaged, or missing.
• Small replacement part that supports overall appliance stability and safe operation.

• One screw as shown/packaged by the manufacturer.

• Use the correct screwdriver or bit to avoid stripping the screw head.
• Ensure the appliance is powered off and disconnected from the power source before accessing internal components.
• Do not overtighten; snug to manufacturer torque or until the part is secure.
• If mounting hardware or threaded inserts are damaged, replace or repair those components before installing this screw.

This upper freezer tower bracket secures the ice/tower assembly inside the freezer, keeping the tower aligned so ice fills and dispenses correctly. It restores proper support to reduce movement and rattling. What it does:

• Holds the upper section of the freezer/ice tower in position to maintain alignment
• Prevents tower movement that can cause noise or interfere with ice delivery
• Helps keep internal components stable so ice fills and dispenses normally
• Supports proper fit of surrounding trim and panels

• Disconnect power to the refrigerator before beginning any work
• Remove ice bin and any nearby trim for safe access to the tower area
• Use appropriate tools and retain original fasteners; replace damaged fasteners if needed
• Inspect surrounding components for damage and test ice operation after installation

This discharge pan collects and channels defrost and condensate water away from the evaporator area to help prevent leaks and puddling in the cabinet. It restores proper water routing for safe, reliable cooling performance. What it does:

• Collects melt and condensate water from the evaporator/chill area and directs it to the drain or evaporator heater
• Prevents water from pooling inside the cabinet that can cause leaks or damage
• Replaces cracked, warped, or corroded pans that allow water to escape the drain path
• Helps reduce musty odors and ice buildup caused by standing water

• Inspect mounting tabs, seals, and drain path before installing; replace any damaged clips or gaskets
• Power off the appliance and disconnect power before servicing to avoid shock or injury
• Handle edges carefully; secure the pan so it sits flat and the drain outlet aligns with the drain tube