Pss23mswss Parts

This main board enclosure houses and protects the appliance's electronic control board, keeping wiring and circuitry secure and organized for reliable operation. It helps prevent contact damage and contains the control components in one location. What it does:

• Covers and protects the main electronic control board from debris and accidental contact
• Keeps wiring routed and secured around the control area to reduce strain on connectors
• Helps maintain correct positioning of the control board for consistent electrical connections
• Useful when the original housing is cracked, missing mounting points, or allowing exposed circuitry

• Disconnect power to the appliance before beginning any work to avoid shock or damage
• Handle the control board and connectors gently; avoid touching circuit traces or components
• Keep track of any mounting screws and brackets removed during disassembly for reinstallation

This freezer tower lower bracket secures the lower portion of the freezer air/tower assembly to the cabinet so the tower stays stable and aligned for proper airflow and operation. Replaces a worn, cracked, or broken lower support bracket to reduce tower movement. What it does

• Secures and supports the lower section of the freezer air/tower or trim assembly
• Prevents the tower from shifting, which can cause noise, poor airflow, or misalignment
• Helps maintain proper airflow paths inside the freezer for consistent cooling
• Restores stable mounting after the original bracket becomes cracked, bent, or broken

• One lower freezer tower support bracket

• Disconnect power to the appliance before starting any repair
• Typical install requires removing interior panels and sliding the tower into position; basic hand tools like a screwdriver may be needed
• Handle sharp sheet-metal edges and wear gloves
• If fasteners are damaged or missing, replace them with OEM-specified screws

This middle reflector assembly directs and focuses interior light for a clean, even appearance inside the appliance. It replaces a cracked, missing, or misaligned reflector to restore proper light distribution and finish. What it does:

• Reflects and redirects interior lamp output for improved visibility
• Covers and protects the light area from debris and accidental contact
• Restores finished appearance where a reflector is cracked, discolored, or missing
• Works with the appliance's lamp housing to maintain intended illumination pattern

• One middle reflector assembly

• Disconnect power before starting any work to avoid shock
• Remove shelves or trim as needed to access the reflector; handle carefully to avoid scratches
• Align and secure the reflector into the existing housing using original clips or fasteners
• If lamp or housing is damaged, inspect those components and replace as needed.

This door gasket seals the refrigerator compartment to help maintain proper temperature and energy efficiency. It replaces a worn or damaged seal so cold air stays inside and warm, humid air stays out. What it does:

• Creates an airtight seal around the refrigerator door to reduce temperature fluctuations
• Helps prevent frost build-up and condensation by keeping warm air from entering
• Supports consistent cooling performance and helps reduce energy use
• Commonly replaced when the seal is cracked, torn, flattened, or no longer closes tightly

• Designed for direct replacement; fit by comparing part to the existing gasket before installation
• Clean the door flange and remove old gasket adhesive/residue for best seal
• Work slowly around corners to seat the gasket evenly; heat (hair dryer) may help soften stiffer gaskets for fitting
• Disconnect power if required by your model before performing any repairs and follow all safety instructions in your appliance manual

This wire actuator engages the refrigerator dispenser paddle to activate water or ice dispensing. It restores reliable mechanical actuation for responsive dispenser operation without replacing the entire dispenser assembly. What it does:

• Translates paddle movement into the dispenser switch action so water or ice starts when the paddle is pressed
• Helps correct a dispenser that doesn't activate when the paddle is pushed
• Replaces a bent, broken or worn actuator wire that can cause inconsistent dispensing
• Works with the dispenser lever and switch assembly to restore proper alignment and motion

• Includes: 1 wire actuator for dispenser

• Disconnect power (unplug or shut off breaker) and turn off the water supply before starting
• Remove dispenser trim/paddle to access and replace the actuator; avoid forcing plastic clips
• Verify alignment with the dispenser switch and paddle during reassembly to prevent binding

This evaporator cover is the molded housing that protects the refrigerator evaporator and helps direct airflow for proper cooling. Replaces a cracked, broken or missing cover to help maintain internal airflow and component protection. What it does

• Protects the evaporator coil and nearby components from accidental contact and debris
• Helps channel cold air through the evaporator area for consistent cooling performance
• Reduces the chance of frost buildup on exposed components by keeping airflow directed
• Restores proper fit and alignment of inner cabinet panels after damage

• Disconnect power before servicing; working near evaporator may expose sharp edges and refrigerant lines
• Remove shelves and inner panels as needed to access the evaporator housing
• Handle carefully to avoid cracking the new cover; align mounting tabs and fasteners before securing