Pssf5njxaww Parts

This is the ice bucket assembly for the freezer door dispenser. It stores ice and uses the internal auger and crusher components to move cubes to the chute for dispensing.

• Holds and delivers ice from the freezer to the dispenser chute
• Worn or broken auger/drive can cause no dispense, weak dispense, or ice jamming
• Cracked bin may leak ice or fail to engage the drive
• Damaged crusher parts can lead to only cubes or only crushed ice dispensing

• Unplug refrigerator and remove the ice bin before service
• Transfer any loose ice to a cooler to prevent spills
• Inspect drive coupling and dispenser yoke for wear while the bin is out
• Ensure bucket seats fully and test dispense for both cube and crushed modes

A small metal retainer spring that secures trim and lightweight components so panels and shelves stay aligned and do not rattle. Replaces a worn or broken spring to restore a snug, reliable fit. What it does

• Holds trim, panels or lightweight components in position to prevent sagging or separation
• Stops rattling and vibration caused by loose parts
• Restores correct alignment of removable trim or small assemblies
• Helps maintain proper component engagement during normal use

• One retainer spring

• Disconnect power (unplug or switch off circuit) before working on appliances
• Use basic hand tools; access may require removing adjacent trim or clips
• Handle spring and surrounding trim carefully to avoid scratches or damage
• Replace damaged or missing mounting hardware before reassembly

This cam closure is the small plastic latch that helps the freezer door align and stay closed, restoring a tight seal for efficient cooling and preventing frost buildup. Fits the freezer door hinge area and replaces worn or broken closures. What it does:

• Guides and secures the freezer door into the closed position for a reliable seal
• Replaces broken, cracked, or missing cam closures that let the door sag or catch
• Helps reduce air leaks that can cause frost buildup or higher energy use
• Works with the freezer hinge/cam assembly to maintain proper door alignment

• Disconnect power before working on the refrigerator to avoid electrical or injury risk.
• Remove the freezer door or inner liner panels as required to access the cam closure; follow the refrigerator model service manual.
• Install the cam in the correct orientation and ensure smooth door movement and alignment before reassembly.
• If hinges, screws, or adjacent parts are damaged, inspect/replace those parts as needed for a lasting repair.

A stationary blades assembly that secures the stationary blade in place so the cutting or dispensing mechanism operates smoothly. Replacing a worn or broken assembly restores proper blade alignment and reduces noise or poor cutting performance. What it does:

• Holds the stationary blade securely to stabilize rotation and cutting action
• Maintains correct blade alignment to prevent wobble, jamming, or uneven cutting
• Helps reduce abnormal noise and vibration caused by a loose or damaged blade mount
• Restores reliable operation of the appliance's blade/dispensing mechanism when original part is worn or cracked

• One stationary blades assembly

• Disconnect power (or unplug) and turn off water supply if applicable before beginning repair
• Remove access panels or covers to reach the blade area; keep track of fasteners and trim
• Inspect mating parts (rotor, fasteners, seals) for wear and replace if damaged

This rear gasket cover secures the refrigerator door gasket and helps maintain a clean seal at the back edge of the door. It restores proper gasket alignment and helps reduce air leaks and moisture buildup. What it does:

• Holds the rear edge of the door gasket in place for a consistent seal.
• Helps prevent cold air loss and condensation by keeping the gasket aligned.
• Reduces rubbing and wear on the gasket edge caused by movement.
• Commonly replaced when the cover is cracked, missing, or allows the gasket to pull loose.

• One rear gasket cover.

• Remove power to the appliance before beginning any work.
• Typically installs by snapping or sliding into the door gasket channel; inspect surrounding trim for damage.
• Use basic hand tools; avoid forcing the cover to prevent breaking the part or the door.
• If gasket damage is present, replace the gasket as needed to ensure a proper seal.

This lower front trim piece attaches to the refrigerator base to cover and protect the grille area while keeping the appliance's front panel looking finished. It restores appearance and helps keep debris away from vents and components. What it does:

• Covers the lower front grille opening for a finished, OEM appearance
• Protects underlying vents and components from dust and accidental contact
• Helps direct airflow around the condenser/vent area for proper operation
• Replaces damaged, cracked, or missing trim to improve aesthetics

• One grille recess lower front trim

• Disconnect power to the refrigerator before attempting installation
• Typically secures with snap tabs and/or screws; align tabs and press or fasten as required
• Handle carefully to avoid scratching the finish and to prevent breakage of plastic tabs
• Obtain OEM replacements for secure installation

This slide and bracket assembly replaces a worn or broken refrigerator drawer slide to restore smooth opening and secure drawer support. Designed to align and guide the drawer while preventing sagging or binding. What it does:

• Replaces the drawer slide and mounting bracket so the drawer glides correctly
• Supports the weight of the drawer and its contents to prevent sagging
• Helps stop sticking, rough movement, or misalignment when opening/closing the drawer
• Restores proper drawer tracking for full insertion and removal

• One slide and bracket assembly

• Intended for refrigerator drawer application; verify fit against your OEM part number before ordering
• Basic hand tools required; follow manufacturer's service manual for access and removal steps
• Disconnect power or unplug the appliance if accessing electrical components nearby
• If fasteners or clips are damaged, replace them with OEM-specified hardware

This silicon controlled rectifier (SCR) is an electronic switching device used to control power to oven/stove heating circuits, helping the appliance regulate temperature and heat output for cooking performance. What it does:

• Switches and regulates AC power to heating elements for controlled heat
• Enables cycle-based or phase-controlled heating used by oven/range controls
• Common replacement when an element won't heat consistently or unit won't maintain temperature
• Helps stop erratic heating caused by a failed power control component

• Disconnect power to the appliance before inspecting or replacing the SCR
• Observe ESD precautions and handle the component by insulated edges

This bottom hinge and pin assembly secures and supports the lower refrigerator/freezer door, allowing smooth pivoting and proper alignment for reliable opening and closing. It replaces a worn or bent hinge to restore door stability. What it does:

• Provides a stable pivot point for the lower door to ensure correct alignment and smooth operation
• Helps prevent door sagging, rubbing, or misalignment that can cause poor sealing or uneven gaps
• Fits the lower hinge location and transfers door weight to the cabinet frame
• Works with existing hinge housing and mounting points to restore factory movement

• Turn off power to the appliance and remove all items from the door before starting
• Support the door securely while removing and installing the hinge to avoid injury or damage
• Use appropriate hand tools; tighten fasteners to secure but avoid over-torquing

This front-chill seal is the replacement gasket that seals the refrigerator's front chill/drawer area to help maintain proper temperature and reduce moisture intrusion. Restores a tighter seal to improve cooling performance in the drawer area. What it does

• Replaces worn, torn or compressed front chill/drawer gasket that lets cold air escape
• Helps maintain even temperature in the chill/deli drawer and reduce frost buildup
• Reduces moisture and odor transfer between compartments caused by a failing seal
• Common symptom: drawer not staying cold or visible gaps around the drawer edge

• Designed for a direct-fit replacement; remove the drawer or access panel as needed to reach the gasket
• Clean the mounting flange and channel before installing the new seal for best adhesion/seating
• Seat the gasket evenly into the channel; use gentle, even pressure to avoid distortion
• Disconnect power before removing panels or working near refrigeration components

This replacement cover hinge secures and supports the appliance access cover, restoring proper alignment and smooth opening/closing. It's a direct-fit part that helps stop sagging or loose covers and reduces rattling during operation. What it does:

• Replaces a worn or broken cover hinge to restore proper cover alignment and operation
• Helps stop cover sagging, uneven gaps, or covers that won't stay closed
• Reduces rattling or vibration caused by a loose hinge
• Matches white trim for a clean, factory appearance

• High-level fit: installs at the cover mounting point using the factory screws or clips
• Safety first: disconnect power to the appliance before beginning any repair
• Handle trim pieces carefully to avoid scratching or cracking during removal/installation

This bottom door hinge secures the refrigerator/freezer door at the lower pivot and helps ensure smooth, stable opening and closing. Durable replacement that restores proper door alignment and keeps the seal functioning. What it does:

• Supports the bottom of the door and serves as the lower pivot point
• Keeps the door aligned so it closes fully and maintains a proper seal
• Reduces door sag, rubbing, or uneven gaps that cause cooling issues
• Fits and functions as the factory replacement hinge for compatible GE units

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use appropriate hand tools; avoid overtightening fasteners which can misalign the door

This is a mobility screw used to secure mobility-related components in compatible appliances, providing a reliable fastener for stable operation and correct alignment. It replaces worn or missing screws to restore secure mounting. What it does

• Fastens and secures mobility/bracket components to prevent movement or misalignment.
• Helps maintain proper alignment of moving parts that can cause noise or binding when loose.
• Commonly replaced when mounting points are stripped, damaged, or missing.
• Small replacement part that supports overall appliance stability and safe operation.

• One screw as shown/packaged by the manufacturer.

• Use the correct screwdriver or bit to avoid stripping the screw head.
• Ensure the appliance is powered off and disconnected from the power source before accessing internal components.
• Do not overtighten; snug to manufacturer torque or until the part is secure.
• If mounting hardware or threaded inserts are damaged, replace or repair those components before installing this screw.