Pwe23kkskhss Parts

The Water Filter Bypass Plug is an OEM part for GE refrigerators. It allows the refrigerator to operate without a water filter by creating a direct connection for the water flow.

Causes of a bad Water Filter Bypass Plug can include wear and tear from regular use, damage from improper installation or removal, and degradation of the sealing components that ensure a tight fit.

Symptoms of a bad Water Filter Bypass Plug include:

• Water leaks from the filter housing
• Reduced or no water flow to the dispenser or ice maker
• Error messages related to the water filter on the control panel
• Improper fit or difficulty in installing the bypass plug

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Left side

This compressor start device is the relay-and-overload assembly that helps your refrigerator's compressor start and protects it from overheating. Replacing a failing start device can stop repeated clicking and help restore consistent cooling performance.

• Provides the initial start circuit for the compressor, then disengages once running
• Protects the compressor by opening on overcurrent/overheating (overload protection)
• Helps address symptoms like: compressor won't start, repeated clicking, and warm fridge/freezer
• Often found heat-damaged or cracked when failed

• Disconnect power before servicing; access the compressor compartment at the rear
• Note wire positions; pull the old start device straight off the compressor pins
• Transfer wires to the new device; push it fully onto the compressor terminals until seated
• Reinstall the rear cover and restore power; verify normal compressor start

This articulating mullion assembly is the folding center strip for the fresh food section. It mounts to one refrigerator door and swings over the center gap to complete the door seal, helping maintain temperature and reduce condensation.

• Folds over the gap between doors to create a reliable air seal
• Helps keep cold air in and warm air out for consistent cooling
• Replaces a broken, cracked, or misaligned flipper that won't fold or latch properly
• Common symptoms: moisture or frost between doors, doors not closing/sealing, or temperature fluctuations near the door opening

• Disconnect power before servicing.
• Open the doors, remove any covers/screws securing the mullion, and note orientation for reassembly.
• Transfer any reusable trims/caps from the old mullion to the new assembly if required.
• Verify smooth folding action and full gasket contact before restoring power.

This freezer door bin support secures the door bin to the freezer door liner, keeping it level and firmly in place. Replace a cracked or missing support to restore stable storage and prevent the bin from popping off the door.

• Supports and locks the freezer door bin to the door liner
• Helps prevent bin wobble, sagging, or unexpected drops
• Replace if tabs are broken, the support is cracked, or the bin won't stay seated
• Common symptoms: bin tilts, falls off, or rattles on the door

• Unplug the refrigerator and remove items from the bin before servicing
• Lift out the door bin to access the support
• Release the old support from the liner; align and press the new support fully into place until secure
• Reinstall the bin and confirm a snug, stable fit before restocking

The Switch Light is an OEM part for GE refrigerators. It is designed to activate the refrigerator’s interior light when the door is opened and turn it off when the door is closed. This ensures visibility inside the refrigerator, making it easy to locate items even in low-light conditions.

Over time, the switch light can become faulty due to wear and tear, exposure to moisture, or repeated use. These factors can cause the switch to malfunction or become unresponsive.

Symptoms of a bad switch light include:

• The refrigerator light not turning on when the door is opened
• The light staying on even when the door is closed
• Flickering or dimming of the interior light
• No response from the light switch when the door is opened or closed

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore usable storage on your freezer door with this replacement bin. It mounts to the door to organize small items and keep them secure when opening and closing the freezer.

• Attaches to the freezer door to hold and organize frozen items
• Helps prevent items from tipping or falling when the door moves
• Replace if the bin is cracked, broken, warped, missing, or won't stay seated
• Designed to fit the specified door position on models that use this bin

• Remove the old bin by lifting up and pulling out of the door slots
• Align the new bin's tabs/hooks with the door rails and slide down until fully seated
• No tools or electrical work required; handle plastic carefully to avoid cracking
• Allow it to reach room temperature before installing

Mounts between the fresh food fan assembly and its housing to create an airtight, cushioned seal. Replacing a damaged gasket restores proper airflow and helps stabilize refrigerator temperatures while reducing vibration and noise from the fan area.

• Seals the interface between the fresh food fan and the duct/liner to prevent air leaks
• Directs airflow through the evaporator and vents for consistent cooling
• Cushions the fan mount to minimize vibration and rattling
• Failure may present as weak airflow, temperature swings, or new buzzing near the fresh food fan cover

• Disconnect power before servicing to avoid electrical shock
• Remove shelves/bins and the fresh food rear interior panel to access the fan
• Note gasket orientation; seat it evenly with no gaps and avoid stretching/compressing it
• Ensure the fan spins freely and runs quietly before reassembly

This replacement door bin fits the right-hand fresh food door and restores organized storage for condiments, jars, and small bottles. It helps maximize usable space and keeps frequently used items easy to see and reach.

• Holds condiments, small bottles, and jars on the right fresh food door
• Replaces a cracked, broken, or missing door bin
• Snaps into the molded slots on the door liner for secure storage
• Common symptoms: cracked plastic, broken tabs, won't stay seated, items tipping

• Disconnect power before servicing
• Empty and lift the old bin up and out of the door liner slots
• Align the new bin with the slots and press down until fully seated
• Confirm a secure fit before loading items

This refrigerator shelf assembly restores a sturdy, level storage surface inside your refrigerator. Replace a cracked, broken, or missing shelf to keep food organized and maintain proper spacing for airflow and consistent cooling.

• Provides a flat, supportive surface for food and containers
• Seats into factory supports at the correct height and alignment
• Helps organize contents and maintain clear airflow paths
• Common symptoms: cracked or shattered shelf, broken frame tabs, shelf sags or won't sit level, missing shelf

• Remove all items from the area; handle the shelf carefully—edges can be sharp and glass can break; wear cut-resistant gloves
• Lift/slide the old shelf out of the side supports; inspect supports for damage
• Seat the new shelf fully into the rails or pegs so it's level and secure
• Confirm it's properly supported before reloading with items

The ART FRAME VP ASM is an OEM replacement part for GE refrigerators. It provides an adjustable lid solution to seal the humidified drawers within the fresh food compartment. 

Symptoms of a bad ART FRAME VP ASM include:

• Gaps that fail to maintain proper humidity levels within drawers
• Covers that will not securely latch or lock into place  
• Cracks or breaks inhibiting a proper seal

Causes can include normal wear over time, and accidental impacts compromising the integrity of the plastic material. Warping may occur from overloading.

This GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Shelf Assembly Tuckaway is an OEM component for GE side-by-side refrigerators equipped with bottom drawer storage. Adjustable and positioned on extension rails within cabinets, it provides extra tucked-away organization and shelving alternatives. Multi-level access relies on fully functional shelving systems.

Causes of a defective tuckaway assembly involve loosened mounting clips reducing secure fit over repeated extension/retraction cycles, wear from constant sliding contact weakening smooth retraction of rails, or damaged runner wheels increasing drag during movement.  

Symptoms include:  

• Shelves not holding steady positions when extended or retracted  
• Dislodged shelves unable to bear moderate weight distribution
• Squeaking and rubbing sounds were heard along the rails during the movement

Replacing with this genuine GE lower drawer shelf ensures reliable tucked storage potential through resilient materials and precision engineering. Compatible with Hotpoint, RCA, or Kenmore lower-tier pantry optimization.
 

The Tube Lead is an OEM part for GE refrigerators. It is responsible for routing water through the unit.

Causes of a bad tube lead can include mineral accumulation restricting flow, loosened compression fittings, or cracked/split tubing exposing water to air.

Symptoms of an issue with the water line tube lead include:

• Slow or inconsistent water and ice production
• Water pressure or temperature fluctuations at the dispenser
• Leaks in the refrigerator's exterior bottom panel

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

The Freezer Fan Cover is an OEM part for GE refrigerators. This shroud housing fits securely over the fan and vent area located inside the freezer compartment walls. It directs airflow while protecting internal fan components.

Symptoms of a bad fan cover include:

• Abnormal noises coming from inside freezer walls
• Inability to adequately circulate air and maintain temperature  
• Detected blockages in the ventilation system

Causes can be related to damaged or degraded fan housing material letting in moisture over many cooling and defrost cycles. Cracks may form affecting component protection.

This GE OEM replacement restores optimum air volume and preserves dependable freezer performance. Featuring rigorous testing, it prevents intrusions into sensitive areas while yielding energy savings. Reliably assists in maintaining frozen foods for owners of GE, Hotpoint, RCA, or comparable-design Kenmore freezers as well.
 

This curved fresh food door handle assembly restores a secure, factory look and grip to your refrigerator's main compartment door. Replace a cracked or loose handle to keep daily openings comfortable and the finish looking clean.

• Attaches to the fresh food door and provides the leverage needed to open and close the compartment
• Restores proper fit and appearance when the original handle is broken, cracked, or missing
• Helps correct wobble or looseness from worn attachment points
• Common signs it's needed: loose or wobbly handle, visible cracks, damaged finish, or a handle that won't stay secured

• Protect the door finish with painter's tape before removing or installing the handle
• This style commonly slides over existing door studs and tightens with hidden set screws—use the correct hex/Allen driver and do not overtighten
• Check that the door gasket seals evenly after installation
• Always follow your product's service manual and use proper hand protection

The Fresh Food Evaporator Cover with Deli Drawer Fan is an OEM part for GE refrigerators. Located inside the refrigerator compartment, this assembly helps properly circulate cool air throughout. 

Symptoms of a bad evaporator cover or deli fan include:  

• Warm or inconsistent temperatures within sections of the interior
• Frost or ice buildup in areas of poor air circulation
• Abnormal sounds from the fan such as grinding or squealing noises
• The fan fails to spin or rotate when the deli drawer is opened

Causes can be normal wear over time. Dust and debris accumulation may restrict airflow or cause imbalances. Infrequent cleaning allows contaminants to interfere with fan function.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.