Rb5250a1ad Parts

A small rubber bumper that cushions contact points to reduce noise and prevent wear on moving appliance parts. Fits where a soft stop or spacer is needed to protect surfaces and quiet door or panel movement. What it does:

• Acts as a shock absorber to cushion impact between moving parts or panels
• Reduces rattling and vibration for quieter operation
• Prevents metal-to-metal contact that can cause surface wear or chipping
• Maintains proper spacing where a soft stop or spacer is required

• Typically presses or snaps into a mounting hole or onto a stud; orientation before installing
• Clean mating surfaces to ensure a secure fit and proper adhesion if applicable
• Replace only when the old bumper is cracked, flattened, or missing
• Disconnect power and remove any obstructing panels if working near electrical components

This contoured washer is a shaped fastening washer used on compatible GE top-load washers to secure and cushion mating parts. It helps maintain proper alignment and reduces wear where parts bear against each other. What it does

• Provides a contoured bearing surface to help distribute load and reduce point wear
• Cushions and isolates components to help limit vibration and noise
• Secures fasteners or assemblies in tight, shaped recesses
• Helps maintain correct part alignment for reliable operation

• One contoured washer

• Disconnect power to the washer before servicing to avoid shock or injury
• Use proper tools and observe orientation; tighten fasteners to manufacturer guidance

This replacement screw is a simple fastener used to secure panels, trim, and internal components on GE appliances, restoring proper fit and preventing loose parts. It's a direct-replacement hardware piece for common mounting and assembly points. What it does

• Secures panels, brackets, and trim to prevent rattling or gaps
• Replaces missing, stripped, or corroded fasteners that compromise fit
• Helps maintain proper alignment of controls and components
• Keeps internal parts fixed for safe, reliable operation

• Screw as shown

• Unplug or disconnect power to the appliance before starting repairs
• Use the correct screwdriver or bit to avoid stripping the head
• Install with moderate torque; do not overtighten to prevent thread or component damage
• If threads are damaged or the mating hole is stripped, replace the mating hardware or repair the thread before reuse

This is a right-side guide support that secures and aligns a sliding component so drawers or shelves operate smoothly and stay on track. Replaces a worn or broken guide support to restore proper movement and seating. What it does:

• Holds the right-side guide rail or track in place so the drawer or shelf slides evenly
• Prevents the drawer or shelf from sagging, binding, or falling off the track
• Restores proper alignment when the original guide is cracked, broken, or worn
• Works with the existing rail, clips, and mounting hardware to maintain smooth travel

• Disconnect power or unplug the appliance before accessing internal components
• Access may require removing the drawer, shelf, or front panel—use basic hand tools
• Inspect related clips, rails, and fasteners and replace any damaged pieces for best results

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter

This selector knob replaces a worn or broken stove/oven control knob to restore reliable setting selection and a secure fit on the control shaft. It provides a simple, no-fuss way to regain tactile control of your appliance. What it does:

• Rotates the control shaft to select oven or burner functions and settings.
• Replaces stripped, cracked, or missing knobs that are hard to turn or don't stay in place.
• Helps stop accidental setting changes caused by loose or damaged knobs.
• Matches OEM fit for consistent alignment and operation with the control shaft.

• Disconnect power to the appliance before attempting any service to avoid injury.
• Most knobs pull straight off the control shaft; align splines and push until seated.
• If the knob is tight or stuck, use a gentle pulling tool or apply a small amount of penetrating lubricant to the shaft—avoid excessive force.
• If the control shaft or retaining hardware is damaged, replace or repair those components as needed.

This bracket base is a replacement support bracket that secures and stabilizes appliance components, helping restore proper alignment and reduce movement. Use it to replace a cracked, bent, or missing base bracket for safe, stable operation. What it does:

• Provides a sturdy mounting point to secure panels, assemblies, or controls
• Restores proper alignment when a worn or damaged bracket allows shifting
• Helps eliminate vibration or rattling caused by loose support hardware
• Prevents further wear by re-establishing correct component positioning

• One bracket base

• Disconnect power to the appliance before beginning any repair
• Verify orientation and fastener locations against the appliance diagram before removal
• Use the correct size screwdriver or socket to avoid stripping fasteners
• Handle edges carefully and wear gloves; replace any damaged fasteners or clips

Note: 6" surface element

This terminal block assembly provides a secure, insulated connection point where the appliance's incoming power leads join the internal wiring harness. Replacing a damaged or heat-worn block restores reliable power flow and helps prevent overheating at the connection. What it does:

• Connects incoming line, neutral, and ground conductors to the internal wiring
• Provides an insulated barrier to prevent shorts at the power-entry point
• Helps resolve no power or intermittent power issues
• Addresses visible heat damage, melted terminals, or burning odor at the cord connection

• 1 terminal block assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Photograph existing wiring and transfer one wire at a time to maintain correct positions
• Tighten terminals securely; replace any overheated ring lugs or damaged wiring
• Ensure no bare copper is exposed and reinstall any covers or shields before restoring power