Shp65t52uc/09Uc/07 Parts

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This insulating protection strip shields wiring and nearby components from heat and abrasion, helping maintain safe operation and prevent premature wear. It's a low-profile, heat-resistant sleeve used where wiring passes near hot appliance parts. What it does:

• Provides thermal and abrasion protection for wiring and small components
• Helps prevent shorting or insulation damage from heat exposure
• Reduces wear where wires contact sharp edges or moving parts
• Commonly used when replacing control or harness components near heat sources

• One insulating protection strip/sleeve as shown

• Only install with power disconnected and appliance fully cooled
• Position sleeve fully over exposed wiring or component and secure per OEM routing
• Inspect surrounding wiring and connectors for damage; replace any frayed insulation

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

This base panel covers the lower-front opening of the dishwasher, protecting internal components and completing the finished look. Replace a bent, rusted, or missing panel to restore proper shielding and help reduce vibration and noise.

• Covers the bottom-front opening of the dishwasher
• Helps protect wiring, hoses, and moving parts from debris and accidental contact
• Contributes to sound damping and a clean, finished appearance
• Typical indicators: panel is dented, rusted, rattling, loose, or missing

• Disconnect power and turn off water supply before servicing
• Remove the mounting screws and support the old panel as you take it off
• Align the new panel and secure with the original hardware; do not overtighten
• Restore power and verify the panel is secure and free of vibration

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This trim strip finishes and protects the exposed edge of the appliance where it installs, helping secure adjacent panels and giving a clean, finished look. Replacing a damaged strip can improve fit and appearance.

• Provides a finished edge and helps secure panels or covers in place
• Helps prevent gaps that can collect debris
• Common fix when the existing strip is cracked, bent, loose, or missing
• Reduce rattles or vibrations caused by an ill-fitting trim piece

• Disconnect power and shut off any utilities before servicing
• Note orientation/position of the old strip before removal
• Press or fasten the new strip into the same mounting points; do not force
• After installation, recheck clearances and panel alignment

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

This replacement outer door restores the finished exterior of the appliance door, protecting inner components and bringing back a clean, secure fit when the original is damaged or missing. It's also known as the outer door panel/skin. What it does

• Provides the exterior surface of the door and mounting points for trim or handle (model dependent)
• Shields the inner door assembly from impacts and wear
• Helps maintain proper door alignment and smooth operation
• Common symptoms: dents, cracks, broken tabs, loose or rattling door panel

• One outer door

• Disconnect power before servicing; wear cut-resistant gloves
• Open the door and support the panel while removing perimeter fasteners
• Transfer any reusable hardware, trim, or insulation from the old panel as needed
• Reinstall fasteners without overtightening and verify door alignment and operation

This facia panel is the finished front cover that restores the dishwasher's appearance and protects the control area. Replacing a cracked or damaged facia returns a clean, finished look and helps shield internal components from debris. What it does:

• Provides the finished front surface and cosmetic cover for the dishwasher door/control area.
• Protects controls, wiring and connectors behind the door from moisture and debris.
• Replaces cracked, dented or heavily scratched facia that detracts from the appliance's appearance.
• Helps maintain proper alignment of trim and covers that sit at the front of the door.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Removal typically requires opening the door and removing screws or clips from the inner door panel; follow the model-specific service instructions.
• Handle clips and mounting tabs carefully to avoid breakage; reuse existing hardware if undamaged.

This replacement control panel button restores a worn, broken or missing push button so your appliance's controls can be operated easily and reliably. It matches the original shape and snap-fit for a clean finish. What it does

• Acts as the user interface button on the appliance control panel for selecting cycles or features
• Replaces cracked, stripped, loose or missing buttons that won't depress or return properly
• Helps restore tactile feedback and proper button travel for responsive control input
• Prevents debris and moisture from entering the switch area when installed correctly

• Replacement control panel button (single)

• Power off and disconnect the appliance before attempting any repair
• Typically installs by snapping into the control panel; access may require removal of the front panel or control console
• Avoid forcing the part; align tabs and press evenly until it clicks into place
• If the underlying switch or actuator is damaged, replace both components to ensure proper function

The Insert is an OEM component specifically designed for select Bosch dishwashers. Located inside the tub basin, the tines provide the necessary friction to help clean dishes. 

Causes of a bad insert can include mineral buildup that prevents proper movement or damage from dropped utensils that have bent the tines out of place.

Symptoms of a bad insert include:

• Dishes still feeling dirty after the wash cycle   
• Rust or mineral deposits visible on the tines
• Tines that are bent or missing which reduces cleaning surface area

Replacing the insert with this OEM Bosch part restores optimal cleaning performance. Compatible with 300 series models, it features stainless steel construction that withstands corrosion from detergents. This replacement insert is warranted to perform as the original Bosch design for reliable dish cleaning.
 

This Bosch Dishwasher Insert is an OEM part for Bosch dishwashers, specifically designed to enhance the interior functionality of your appliance. The insert is a vital component that aids in the organization and secure placement of dishes, utensils, and other items during the wash cycle.

Common causes of damage to a dishwasher insert include physical strain from overloading, exposure to high temperatures and harsh detergents, and general wear and tear. These factors can lead to warping, cracking, or the breakdown of the insert's structure.

Symptoms of a bad insert include:

• Difficulty in fitting dishes and utensils properly.
• Reduced cleaning effectiveness due to improper loading.
• Noticeable cracks, warps, or breakage in the insert structure.
• Loose or unstable compartments within the insert.
• Difficulty in sliding or securing the insert inside the dishwasher.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.