Shp865zd6n/01 Parts

This suspension damper stabilizes the tub/drum by absorbing movement and vibration during operation. Replacing a worn damper helps reduce shaking and noise, improving spin performance and overall machine stability. What it does:

• Absorbs and controls tub/drum movement to reduce vibration and noise
• Helps prevent banging, "walking," or out-of-balance shutdowns during spin
• Can address excessive shaking, rattling, and longer spin times
• Restores smoother, more controlled operation when the original damper is worn

• One suspension damper

• Disconnect power and turn off water supply before servicing
• Access location varies by model; support the tub/drum to relieve load before removal
• Note orientation and reuse existing mounting hardware if new fasteners aren't provided
• After installation, re-level the appliance and run a test cycle to verify stability

This overflow component directs excess water safely back into the dishwasher's water path to help prevent overfilling and leaks. Replace if damaged to restore correct water management and leak protection.

• Guides overflow water away from the tub into the proper return/drain path
• Helps maintain correct water level during fill
• Can address water collecting in the base pan or leaking from the lower front area
• Useful when the leak protection/float has been tripped or cycles stop due to a detected leak

• Disconnect power and turn off the water supply before servicing
• Access the overflow/water-channel area per your model's service procedure
• Note orientation and transfer any clips or seals from the old part if present
• Reassemble, restore power/water, and run a short cycle to check for leaks

This holder/retainer secures its mating part in the correct position inside the appliance, preventing unwanted movement and ensuring consistent operation. Replace a cracked or missing holder to restore a solid, factory fit and reliable performance.

• Supports and locks the attached component or rack/accessory in place
• Helps prevent vibration, rattling, or misalignment during use
• Typical signs of failure: broken tabs, visible cracks, looseness, or the part no longer staying secured
• Restores proper positioning of the related component for consistent function

• Disconnect power at the breaker; shut off water supply if applicable
• Note the holder's orientation; take a photo before removal
• Reuse existing screws/fasteners if none are supplied with the part
• Seat fully until it clicks/locks; do not overtighten into plastic

This cable harness routes power and signals between appliance control and components to restore reliable electrical connections. It replaces a damaged or worn harness to help eliminate intermittent operation and connectivity issues. What it does:

• Replaces the main wiring harness that links controls, sensors, and motors for proper electrical communication
• Restores reliable power and signal paths to correct intermittent power, non-responsive controls, or components that won't run
• Ensures secure connector mating to prevent arcing and poor contact
• Matches OEM connector types and wire lengths to fit in the original routing

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock
• Compare the new harness to the old one for connector types and routing before installation
• Handle connectors by the housings; do not pull on wires. Ensure all plugs snap fully into place

This genuine replacement spring restores the proper return force and smooth movement of the connected mechanism in your appliance. Replacing a worn or broken spring helps the assembly operate consistently and return to position as designed. What it does

• Provides the return/tension force for the associated lever, latch, or hinge mechanism
• Helps the mechanism move smoothly and maintain correct alignment
• Direct replacement for a stretched, weakened, or broken spring
• Common symptoms: weak or inconsistent tension, sticking or failure to return, uneven feel, or visible spring damage

• Includes: Spring

• Disconnect power before service; also shut off water supply
• Note the original routing/orientation and take a reference photo before removal
• Control tension with needle-nose pliers; wear gloves and eye protection
• If the mechanism uses matched springs in pairs, replace both to keep balanced tension

This replacement insert is a small interior mounting piece that helps secure and align appliance components for reliable operation and a finished appearance. It restores proper fit where worn, loose, or damaged inserts allow rattling or misalignment. What it does:

• Provides a stable mounting or seating surface for adjacent components
• Reduces movement, vibration, or rattling caused by a damaged insert
• Helps maintain proper alignment that supports normal operation of the assembly
• Can prevent further wear to surrounding trim or mounting points when replaced

• One insert

• High-level replacement; typically accessed from the appliance interior
• Use basic hand tools; avoid force that could break surrounding plastic or trim
• Disconnect power (and water for dishwashers) before servicing to reduce shock and injury risk

This program power control module is the dishwasher's main electronic control that manages cycles and power to components for reliable operation. Replacing a failed module restores control of wash, drain and fill sequences. What it does:

• Receives user commands and runs selected wash programs by sending power to valves, pumps and motors
• Monitors and coordinates cycle timing and heater/power outputs
• Common symptoms of a failing module: dishwasher won't start, displays error codes, or buttons/controls are unresponsive
• Replacing the module often resolves intermittent operation, no-power conditions, and program errors

• Disconnect power at the circuit breaker before servicing to avoid shock or damage
• Handle the board by edges; avoid touching circuitry and static-sensitive components
• Verify wiring connections and connector seating match factory positions before restoring power

This replacement frame restores the appliance's front cabinet trim for a clean, finished appearance and helps secure the control panel and door assembly. It's a direct-fit exterior trim piece designed to return proper alignment and protection. What it does

• Provides structural support and alignment for the front panel and control area
• Covers and protects internal edges from dirt, moisture, and impact
• Helps stop rattling or vibration caused by a warped or damaged trim
• Common symptom: visible damage, cracks, loose or misaligned front trim

• Remove power to the appliance before starting work to avoid electrical shock
• Small hand tools typically required; follow OEM disassembly sequence for access
• Handle trim carefully to avoid scratches; use a soft surface to rest parts
• If clips or screws appear damaged, replace them separately.

This insulating protection strip shields wiring and nearby components from heat and abrasion, helping maintain safe operation and prevent premature wear. It's a low-profile, heat-resistant sleeve used where wiring passes near hot appliance parts. What it does:

• Provides thermal and abrasion protection for wiring and small components
• Helps prevent shorting or insulation damage from heat exposure
• Reduces wear where wires contact sharp edges or moving parts
• Commonly used when replacing control or harness components near heat sources

• One insulating protection strip/sleeve as shown

• Only install with power disconnected and appliance fully cooled
• Position sleeve fully over exposed wiring or component and secure per OEM routing
• Inspect surrounding wiring and connectors for damage; replace any frayed insulation

This is a replacement screw used to secure panels, trim pieces, and small brackets on compatible Bosch appliances — a simple hardware fix that restores proper fit and stops rattling or loose parts. What it does:

• Fastens outer panels, control bezels, or internal brackets to the appliance chassis
• Keeps panels aligned so doors and controls fit and operate correctly
• Stops vibration noise caused by loose or missing fasteners
• Replaces damaged, stripped, or corroded screws

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread by hand to start, then snug; avoid over-tightening which can strip threads or crack panels
• If threads are damaged, replace the mating nut or threaded insert per OEM guidance

This access cover replaces a damaged or missing exterior panel to restore proper fit and protect internal components from debris and moisture. It helps maintain appliance appearance and prevents accidental contact with internal parts. What it does:

• Covers and protects internal components at the specified access point
• Helps prevent debris buildup and accidental contact with wiring or moving parts
• Restores a secure mounting surface for adjacent panels or controls
• Reduces rattles or vibration caused by a loose or broken cover

• One replacement cover (1 piece)

• Disconnect power to the appliance before beginning any work
• Installation may require basic hand tools; handle edges carefully to avoid cuts
• Align mounting tabs and fasten with the factory screws or clips; do not overtighten

This cable harness routes power and signals between appliance components to restore electrical connections and control functions. It replaces a damaged or worn wiring assembly to help re-establish reliable operation and communication between modules. What it does:

• Connects controls, sensors, and motors by providing the necessary power and signal pathways
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or loss of function
• Helps stop electrical faults like shorts or open circuits when the original harness is damaged
• Supports normal component communication so buttons, displays, and cycles respond correctly

• One pre-assembled cable harness

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Inspect connectors and routing path; match connector types and secure harness to existing clips or mounts
• Handle terminals carefully to avoid bending pins; ensure secure, fully seated connections before testing