Shs5avl5uc/01 Parts

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Replacement hood canopy that restores the vent cover and exterior appearance of your range hood. Installs in place of a dented, rusted, or damaged canopy to keep ventilation components protected and maintain a finished look. What it does:

• Covers and protects internal blower, controls and filters from grease, dust and damage
• Directs exhaust airflow through the hood; bent or crushed can disrupt ventilation
• Restores exterior appearance—visible dents, rust or corrosion are common signs it needs replacement
• Provides the proper mounting surface for filters and related hood components

• Disconnect power to the appliance before starting any repair
• Retain existing mounting hardware and seals unless new hardware is specifically listed as included

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

Replacement housing that restores the appliance's outer enclosure and helps protect internal components from damage. Use this part when the original housing is cracked, broken or otherwise compromising appliance stability and appearance. What it does:

• Replaces a damaged outer housing to restore structural support and component protection.
• Helps reduce vibration and rattling caused by cracked or loose enclosure pieces.
• Prevents direct exposure of internal parts to dirt and moisture when intact.
• Improves the appliance's appearance by covering worn or broken bodywork.

• Disconnect power (and water supply if applicable) before beginning any repair.
• Remove control panels or trim as needed to access the housing; keep fasteners for reuse if undamaged.
• Handle edges carefully—metal or molded parts can be sharp.
• Verify part fit and orientation against the old housing before finalizing installation.

The CABLE HARNESS is an OEM part specifically designed for Bosch dishwashers. As the internal wiring backbone, it carries electrical signals operating all wash components according to cycles. 

Symptoms of a faulty cable harness include:

• Random component failures due to intermittent connections
• Repeated error codes relating to components not responding  
• Buzzing noises or excessive warmth around internal wires

Causes can be physical damage exposing wires, cracked wire insulation reducing conductivity over time, or broken connectors inhibiting communication. 

This replacement harness restores function and integrity to the sensitive electrical pathways within the dishwasher. Proper voltage transmission is crucial for wash arms, the pump, the heater, and control boards to seamlessly activate in sequence during cleaning.

Compatible with premium Thermador, Gaggenau, and Kenmore models using matching Bosch systems technology, this OEM harness precisely follows original conduit paths. 

This base panel is the lower kickplate that covers the appliance's front base opening and gives the unit a finished appearance while protecting internal components. It restores the clean look and helps block debris from the cavity. What it does:

• Replaces a damaged, dented, or missing lower kickplate to restore appearance
• Covers and protects internal components at the appliance base from dust and spills
• Helps keep pests and larger debris out of the cavity under the appliance
• Contributes to proper airflow routing at the appliance front (where applicable)

• Designed to mount with the factory fasteners; retain original screws or clips when possible
• Lift or tilt the appliance as needed for access—follow manufacturer safety guidance
• Disconnect power before attempting service that requires moving or tilting the unit
• If fasteners are missing or damaged, replace with manufacturer-specified hardware

This cable supply is the factory replacement wire harness that delivers electrical power between components, restoring reliable connections and stable operation. Use it to replace damaged, frayed, or corroded supply wiring. What it does

• Provides the primary electrical connection between the appliance's power source and internal components.
• Restores continuity when the original cable is cut, burned, or shows visible wire damage.
• Helps stop intermittent power loss, control failures, or components that fail to start due to wiring faults.
• Maintains correct connector fit and routing to prevent shorting or chafing.

• One cable supply (wire harness) as shown.

• Always disconnect power (unplug appliance or switch off breaker) before inspecting or replacing wiring.
• Match connector shapes and wire colors to the original harness before installation; do not modify wires.
• Route the cable away from moving parts, sharp edges, and heat sources; secure with existing clips or fasteners.
• Clean or replace affected connectors to ensure a reliable connection.

The Power Module is an OEM part for Bosch dishwashers. It acts as the central control hub, using integrated circuitry and wiring to direct all electrical functions. Located discreetly within the control panel, the power module operates seamlessly behind the scenes.

Causes of a bad power module are usually failures in the printed circuit boards over time. Exposure to moisture, dust, or drops/impacts inside the dishwasher can cause circuitry to degrade.

Symptoms of a bad power module include:

• Displays or lights flashing or unresponsive
• Inability to start or progress through cycles
• No power transferring to wash motors or heating components
• Fault codes appearing

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door pivot hinge secures and guides an appliance door so it opens and closes smoothly, helping maintain proper door alignment and sealing. It's a direct-fit replacement designed to restore stable door operation. What it does:

• Provides a pivot point to support the appliance door and maintain alignment
• Helps ensure the door closes fully to preserve internal temperature and performance
• Reduces door sag, rubbing, or misalignment that can cause uneven wear or gaps
• Can stop squeaks or binding caused by a worn or damaged hinge

• One hinge

• Disconnect power and empty the door area before starting; follow manufacturer safety instructions
• Support the door during removal and installation to prevent damage or injury
• Use existing fasteners unless replacements are specified by the manufacturer
• Tighten mounting hardware securely and check door alignment after installation

This outer door panel replaces a dented or damaged front on your dishwasher, restoring a clean, factory look and providing the correct mounting surface for the handle and control trim.

• Forms the exterior front of the dishwasher door and covers the inner door assembly
• Provides mounting points for the handle and trim; aligns with your model's control panel design
• Helps keep door insulation in place and reduces vibration
• Typical signs you need this part: dents, deep scratches, bent corners, loose/rattling panel, misaligned handle or trim

• Disconnect power and shut off water supply before beginning
• Open the door and support the panel while removing the inner-perimeter Torx screws
• Separate the old panel and transfer any handle or trim components to the new panel as required
• Use gloves and care—edges can be sharp; reinstall screws evenly without overtightening

This insulating part restores the factory isolation and protection between components inside your appliance. Replacing a worn or missing insulator helps prevent damage from heat or contact so the unit operates safely as designed. What it does:

• Provides the specified insulation and spacing where installed
• Helps prevent heat transfer, shorting, or abrasion between adjacent parts
• Restores proper fit when the original insulator is cracked, deformed, or missing
• Common signs include discoloration, charring, brittleness, or the old piece crumbling/falling out

• 1 insulating part

• Disconnect power and allow the appliance to cool completely before service; shut off water or gas if applicable
• Note the original orientation and placement; take photos for reference
• Install without over-compressing; ensure it seats flat and does not interfere with nearby parts
• Reassemble, restore power, and test for normal operation