Shv4313gb/17 Parts

This door lock is the latch assembly that secures the dishwasher door and tells the control when the door is closed so cycles can start and run safely. It restores proper door closure and control interlock function. What it does:

• Secures the dishwasher door during operation to prevent accidental opening
• Engages the door-switch/sensor so the control will start and continue a cycle
• Prevents water from spilling by ensuring the door stays fully latched during wash
• Common symptom fix: dishwasher won't start or stops mid-cycle because the door won't lock

• One door lock / latch assembly as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the inner door panel; handle the door panel and wiring gently
• Test door operation and run a short cycle after installation to verify proper function

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This sleeve-style insulator protects wiring and components from heat and abrasion, helping maintain safe operation and reduce shorts or premature wear. It's a simple replacement that restores original clearance and protection. What it does:

• Covers and insulates wiring or terminals to prevent chafing and heat damage
• Helps reduce electrical shorts caused by worn or exposed conductors
• Restores proper spacing and component protection after panel or control repairs
• Commonly replaced when insulation is cracked, brittle, or missing

• One sleeve-style insulator (quantity: 1)

• Disconnect power to the appliance before inspecting or replacing electrical insulation
• Slide the sleeve onto the wire or over the terminal so it fully covers exposed conductor or contact points
• Verify routing and clearances so the insulated area does not contact sharp edges or high-heat surfaces
• Inspect surrounding wiring and components for additional damage and replace as needed

The Control Unit is an OEM part for Bosch dishwashers. It is responsible for controlling receiving and interpreting signals from the control panel and other sensors in the dishwasher. It coordinates the timing and sequencing of different parts, such as the motor, water inlet valve, and heating element.

A bad control unit can occur due to electrical malfunctions, power surges, or part failure. Signs of a faulty module include the dishwasher not starting, error codes on the display, or erratic behavior during the cycle.

Symptoms of a bad control unit include:

• The dishwasher not starting or responding 
• Error codes displayed
• Interruptions of the cycle

Replace your faulty control unit with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This installation parts bag contains the small hardware needed to install and secure the dishwasher. It keeps required screws, clips and fasteners together so the unit mounts properly and operates quietly. What it does:

• Provides the mounting screws, clips and small fasteners used during dishwasher installation
• Secures the dishwasher to surrounding cabinetry or countertop to prevent shifting or vibration
• Replaces missing or lost installation hardware included with new units
• Helps ensure a complete installation when paired with the factory installation instructions

• Turn off power and water supply to the appliance before beginning installation.
• Follow the dishwasher installation instructions in the manufacturer service or user manual.
• Keep hardware organized and verify quantities against the manual before finishing installation.

This is the front corner block. For rear corner block use 00263093.

This replacement silverware basket holds forks, knives and spoons so utensils stay organized and clean during the dishwasher cycle. It restores a convenient, secure place for cutlery and helps prevent nesting for better wash coverage. What it does:

• Holds and separates silverware to improve cleaning and prevent items from nesting
• Provides a removable container that stays in place during wash cycles
• Fits into the lower rack to keep utensils contained and easy to unload
• Helps protect small items from falling to the tub or blocking the spray arm

• No tools typically required; slides or snaps into the lower rack location
• Remove all dishes and power off/dry area before installing to avoid injury
• Inspect rack tines and basket clips for damage; replace if broken to ensure proper fit

This holder is a molded mounting bracket that secures internal components and helps maintain proper alignment for reliable operation. It replaces a worn or broken support to restore fit and function. What it does:

• Secures and supports the associated component to prevent movement or misalignment
• Restores proper positioning when a cracked or broken bracket causes rattling or loose parts
• Helps reduce vibration and intermittent contact that can cause noise or poor performance
• Fits where the original molded holder has failed or become distorted

• Disconnect power and shut off water before replacing the part
• Remove access panels as needed to reach the mounting location; retain screws or clips for reassembly
• Align the holder with existing bosses or screw holes and secure with the original fasteners
• If clips or adjacent parts are damaged, inspect and replace as necessary for a secure fit