Shvt6853uc/04 Parts

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door lock is the latch assembly that secures the dishwasher door and tells the control when the door is closed so cycles can start and run safely. It restores proper door closure and control interlock function. What it does:

• Secures the dishwasher door during operation to prevent accidental opening
• Engages the door-switch/sensor so the control will start and continue a cycle
• Prevents water from spilling by ensuring the door stays fully latched during wash
• Common symptom fix: dishwasher won't start or stops mid-cycle because the door won't lock

• One door lock / latch assembly as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the inner door panel; handle the door panel and wiring gently
• Test door operation and run a short cycle after installation to verify proper function

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This sleeve-style insulator protects wiring and components from heat and abrasion, helping maintain safe operation and reduce shorts or premature wear. It's a simple replacement that restores original clearance and protection. What it does:

• Covers and insulates wiring or terminals to prevent chafing and heat damage
• Helps reduce electrical shorts caused by worn or exposed conductors
• Restores proper spacing and component protection after panel or control repairs
• Commonly replaced when insulation is cracked, brittle, or missing

• One sleeve-style insulator (quantity: 1)

• Disconnect power to the appliance before inspecting or replacing electrical insulation
• Slide the sleeve onto the wire or over the terminal so it fully covers exposed conductor or contact points
• Verify routing and clearances so the insulated area does not contact sharp edges or high-heat surfaces
• Inspect surrounding wiring and components for additional damage and replace as needed

The Control Unit is an OEM part for Bosch dishwashers. It is responsible for controlling receiving and interpreting signals from the control panel and other sensors in the dishwasher. It coordinates the timing and sequencing of different parts, such as the motor, water inlet valve, and heating element.

A bad control unit can occur due to electrical malfunctions, power surges, or part failure. Signs of a faulty module include the dishwasher not starting, error codes on the display, or erratic behavior during the cycle.

Symptoms of a bad control unit include:

• The dishwasher not starting or responding 
• Error codes displayed
• Interruptions of the cycle

Replace your faulty control unit with this genuine OEM Bosch part to restore your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This actuator assembly operates the dishwasher's top rack mechanisms to enable proper rack movement and adjustment. Replacing a worn or broken top-rack actuator restores reliable rack travel and prevents misalignment during cycles. What it does:

• Drives or releases the top rack adjustment/advance mechanism so the rack moves and positions correctly.
• Stops binding or uneven rack travel caused by a failed actuator.
• Helps prevent scraping, jamming, or unusual noises from the top rack area when loading or during cycles.
• Works as the mechanical linkage between the rack and the dishwasher's internal drive components.

• Disconnect power and water supply before starting any repair.
• Follow OEM disassembly steps for access—usually involves removing the top rack and inner paneling to reach the actuator.
• Inspect surrounding mounts and linkages; replace any damaged clips or screws to ensure secure operation.

A small replacement magnet plunger that secures top-rack components and helps maintain proper alignment and operation. Use this part when the top-rack magnet is damaged, loose, or no longer holds as intended. What it does:

• Provides magnetic retention for top-rack assemblies and related components
• Restores proper alignment and engagement of the top-rack magnet interface
• Can reduce rattling or shifting of the top rack caused by a worn or missing magnet
• May be needed if the original plunger is cracked, corroded, or detached

• One magnet plunger

• Designed for top-rack application only; confirm correct orientation before installing
• Turn off power to the appliance and follow all safety guidelines before servicing
• Use basic hand tools; avoid forcing components to prevent breakage

This installation parts bag contains the small hardware needed to install and secure the dishwasher. It keeps required screws, clips and fasteners together so the unit mounts properly and operates quietly. What it does:

• Provides the mounting screws, clips and small fasteners used during dishwasher installation
• Secures the dishwasher to surrounding cabinetry or countertop to prevent shifting or vibration
• Replaces missing or lost installation hardware included with new units
• Helps ensure a complete installation when paired with the factory installation instructions

• Turn off power and water supply to the appliance before beginning installation.
• Follow the dishwasher installation instructions in the manufacturer service or user manual.
• Keep hardware organized and verify quantities against the manual before finishing installation.

This front base sound insulation is a factory-style cotton pad that helps reduce dishwasher operating noise and provides thermal cushioning under the tub. It restores the appliance's original sound-dampening and insulation where worn or missing. What it does:

• Dampens vibration and reduces motor/tub noise heard during cycles
• Provides a thermal buffer under the dishwasher base to help maintain stable temperatures
• Helps prevent rattles and improves overall quiet operation when installed correctly
• Restores OEM-fit insulation performance after damage, wear, or removal

• One front base sound insulation pad (cotton), as shown

• Disconnect power and water supply before accessing the dishwasher base
• Remove the lower access panel and mounting hardware to reach the insulation area
• Install in the original location; use the same fasteners or adhesive method specified by the manufacturer

This is the front corner block. For rear corner block use 00263093.