Shx65po5uc/60 Parts

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

This is the right side hinge plate. For left side use 00298567.

Spring-style hose clamp that secures flexible water hoses to fittings on select appliances, helping maintain a leak-tight connection at hose joints. Keeps hoses seated to reduce leaks and ensure reliable water flow. What it does:

• Holds flexible inlet, drain, or circulation hoses tightly on barbed fittings and nipples.
• Prevents leaks and water loss at hose connections by maintaining steady clamp pressure.
• Common signs it needs replacement: dripping or pooling near hose connections, a loose or wobbly hose, or visible clamp corrosion or deformation.
• Small, inexpensive part that restores a secure hose connection when the original clamp has failed.

• Always disconnect power and shut off the water supply before servicing appliance plumbing.
• For spring-style clamps, use pliers to open the clamp, position it over the hose, and release slowly so it seats properly; ensure the hose is fully pushed onto the fitting.
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn before installing a new clamp.
• Wear eye protection when compressing or releasing spring clamps to avoid injury from sudden release.

This is the left side hinge plate. For right side use 00298570.

This electrical control switch completes or interrupts the power circuit that runs a specific appliance function, restoring on/off control for responsive operation and safer use. What it does:

• Acts as the user-activated or circuit-activated on/off control for a discrete function
• Restores power flow when the switch is made, allowing the associated component or cycle to run
• Common symptom: appliance function won't start or respond when the control is pressed or activated
• Common symptom: intermittent operation or no power to a given feature

• One switch

• Disconnect power to the appliance before attempting any service to prevent shock
• Access and replacement steps vary by model; follow the appliance service manual or schematic for safe disassembly
• Handle connectors carefully and confirm secure wiring/terminal seating after installation

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door lock is the latch assembly that secures the dishwasher door and tells the control when the door is closed so cycles can start and run safely. It restores proper door closure and control interlock function. What it does:

• Secures the dishwasher door during operation to prevent accidental opening
• Engages the door-switch/sensor so the control will start and continue a cycle
• Prevents water from spilling by ensuring the door stays fully latched during wash
• Common symptom fix: dishwasher won't start or stops mid-cycle because the door won't lock

• One door lock / latch assembly as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the inner door panel; handle the door panel and wiring gently
• Test door operation and run a short cycle after installation to verify proper function

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This interference capacitor reduces electrical noise and helps protect the appliance's control circuitry from voltage spikes. It's a direct-replacement noise suppressor used where EMI/RFI filtering is required for reliable operation. What it does:

• Suppresses electromagnetic and radio-frequency interference that can affect controls and electronics
• Helps prevent false signals or erratic behavior caused by electrical noise
• Supports stable operation of motors and electronic control boards
• Can reduce audible electrical noise or interference-related symptoms

• Disconnect power at the breaker before inspecting or replacing the capacitor
• Discharge the capacitor and avoid touching terminals; use insulated tools
• Verify wiring match and polarity before connecting

This spring-style hose clamp secures flexible appliance hoses to fittings, helping prevent leaks and loose connections. It's a small but critical fastener that keeps water and drain hoses sealed under normal operation. What it does:

• Holds a rubber or plastic hose firmly onto a barb or spigot to stop leaks
• Prevents hose slippage that can cause water pooling or drip symptoms
• Maintains a compressive seal that resists vibration and thermal cycling
• Commonly used on drain, fill, and circulation hoses in dishwashers and washers

• Disconnect power and shut off water supply before starting work
• Use appropriate pliers (hose clamp or needle-nose) to expand and position the clamp
• Ensure the clamp sits evenly over the hose barb and releases fully to secure the hose
• Inspect the hose and connection for damage; replace hoses if they are cracked or excessively worn

This sump is the dishwasher wash-pump housing that collects and directs wash water to the pump assembly, keeping circulation and drainage working properly. Replacing a damaged sump restores proper water flow and helps prevent leaks. What it does

• Houses the wash pump and channels water between the tub and pump for normal wash and drain cycles.
• Prevents internal leaks by providing a sealed path for wash water.
• Symptoms it commonly addresses: leaking under the dishwasher, poor wash performance, pumps running but no water movement, or intermittent drainage problems.
• Works with the motor/pump assembly and associated seals to maintain correct water flow.

• Disconnect power and shut off water supply before starting any repair.
• Access typically requires removing the lower kickplate and tilting or pulling the dishwasher out to reach the sump area.
• Inspect pump seals, mounting clips, and gaskets during replacement; replace any worn or damaged components separately.