Shx9a15uc Parts

This inlet seal is a small rubber gasket that creates a watertight connection at the dishwasher's water inlet. Replacing a worn seal helps stop leaks and ensures the inlet valve can fill the appliance properly. What it does:

• Seals the water inlet connection to prevent drips or steady leaks underneath the dishwasher
• Maintains a tight seal at the inlet valve so the fill cycle can operate normally
• Commonly replaced when there is visible wear, cracking, or persistent water on the floor
• Helps avoid water damage and the nuisance of repeated drainage or fill errors tied to leaking

• One inlet seal

• Turn off the water supply and disconnect power before servicing
• Remove the inlet valve or access panel as needed to reach the seal; replace with the old seal removed
• Make sure the new seal is seated evenly and the mating surfaces are clean before reassembly

This water distributor directs rinse and wash water to the dishwasher spray arms for even cleaning and circulation. Replacing a faulty distributor restores proper water routing and helps recover normal wash performance. What it does

• Channels wash and rinse water to the spray arms and wash assembly
• Ensures correct water flow timing during wash cycles
• Commonly replaced when spray arms fail to spin or performance drops
• Can cause poor cleaning or uneven spraying if cracked, clogged, or leaking

• Disconnect power and shut off the water supply before starting
• Access typically requires removing the dishwasher base panel or lower access panel
• Handle clips and seals carefully; replace any damaged gaskets to avoid leaks
• Test for leaks and proper spray-arm operation after reassembly

This replacement rail restores smooth, supported movement of a dishwasher rack so loading and unloading work as intended. It replaces a worn, cracked, or bent rail to stop sagging and improve rack alignment. What it does:

• Guides the dishwasher rack along its track for consistent in-and-out motion
• Supports rack weight to prevent tipping or sagging when extended
• Replaces damaged, cracked, or worn rails that cause noisy or jerky operation
• Helps restore proper rack alignment and engagement with the rollers

• Disconnect power and turn off water supply before beginning any repair.
• Remove the affected rack to access and replace the rail; keep small clips or fasteners for reassembly.
• Inspect rack rollers and mounting clips; replace any damaged components for best performance.

This water inlet valve assembly controls water flow into the appliance, restoring normal fill operations and preventing overfilling when the original valve fails. Use this replacement if the unit won't fill or fills irregularly. What it does:

• Opens and closes to admit water into the appliance during fill cycles
• Works with the control system to stop water flow when filling is complete
• Commonly replaces valves that hum, leak at the inlet, or fail to allow water in
• Helps resolve symptoms like no fill, slow fill, or intermittent filling

• Disconnect power and shut off the water supply before beginning repair
• Verify inlet hoses and electrical connections are secure and properly seated
• Inspect sealing surfaces and replace any damaged gaskets or hoses to prevent leaks
• Test operation and check for leaks after reinstalling and restoring power/water

This bottom case is the dishwasher base assembly that protects internal components and helps contain leaks, keeping the wash system stable and secure. It's a direct-fit replacement that restores the appliance's lower enclosure. What it does

• Forms the appliance's lower enclosure to shield the pump, motor and wiring from debris
• Helps direct and contain water in the event of minor leaks to protect surrounding components
• Provides mounting surfaces for lower hardware and supports correct alignment of internal parts
• Can reduce rattles or vibration caused by a damaged or cracked lower shell

• One bottom case

• Disconnect power and water supply before beginning any repair
• Handle the part carefully to avoid damaging edges, clips or mounting tabs
• Keep fasteners and any hardware from the original unit; verify fit and alignment before tightening
• If you see water or corrosion, dry and inspect surrounding components for damage before reassembly

This sealing gasket replaces a worn or damaged seal to help prevent leaks and maintain proper sealing in the appliance. It restores a secure fit where the original seal has hardened, cracked, or lost flexibility. What it does:

• Provides a watertight seal at the mating surfaces to reduce leaks and drips
• Helps maintain proper pressure and containment of fluids during operation
• Prevents debris and odors from passing through compromised gaps
• Commonly replaced when visible cracks, flattening, or leaks occur

• Disconnect power and turn off water supply before starting any repair
• Remove the old seal carefully to avoid damaging surrounding parts
• Ensure mating surfaces are clean and dry before fitting the new seal
• Verify proper orientation and seating; do not use sealants unless explicitly specified by OEM

This is a replacement electrical cable harness used to restore power or signal connections inside compatible appliances. It provides a direct, OEM-style connection for reliable operation and safer performance than damaged wiring. What it does:

• Replaces damaged or frayed wiring that can cause loss of power, intermittent operation, or control failures
• Restores proper electrical connections between components to prevent shorts or erratic behavior
• Helps eliminate issues like unresponsive controls, motors that won't run, or intermittent cycle problems
• Matches the OEM routing and connector style for correct fit and reliable contact

• Disconnect power before starting any repair to avoid shock or injury
• Inspect connectors and routing; replace any retainers or clips that are damaged
• Ensure connectors are fully seated and wires are routed away from moving parts and heat sources

This base panel is the lower kickplate that covers and protects the underside of the dishwasher, restoring the appliance's finished appearance and shielding internal components from dust and debris. It provides a simple cosmetic and protective repair. What it does:

• Covers the dishwasher's lower front area to protect base components and conceal internal parts
• Restores the appliance's original look when the kickplate is dented, cracked, or missing
• Helps reduce dust and debris entering the washer cavity and base assembly
• Stops drafts or light entry under the door when the original panel is damaged

• One base panel

• Remove power to the appliance before beginning work to avoid injury
• Typically secures with screws or clips at the base; keep fasteners from the original panel for reinstallation
• Handle carefully to avoid scratching the finish; alignment may require slight adjustment

This replacement frame restores the appliance's front cabinet trim for a clean, finished appearance and helps secure the control panel and door assembly. It's a direct-fit exterior trim piece designed to return proper alignment and protection. What it does

• Provides structural support and alignment for the front panel and control area
• Covers and protects internal edges from dirt, moisture, and impact
• Helps stop rattling or vibration caused by a warped or damaged trim
• Common symptom: visible damage, cracks, loose or misaligned front trim

• Remove power to the appliance before starting work to avoid electrical shock
• Small hand tools typically required; follow OEM disassembly sequence for access
• Handle trim carefully to avoid scratches; use a soft surface to rest parts
• If clips or screws appear damaged, replace them separately.

This panel frame is the outer trim piece that surrounds and supports the appliance control panel, restoring a finished appearance and protecting internal components from damage and debris. What it does:

• Provides the finished exterior trim around the control panel and door area
• Holds the control panel and related trim pieces in proper alignment
• Protects underlying controls and wiring from everyday bumps and grime
• Replaces cracked, bent, or cosmetically damaged trim that affects appearance

• One panel frame

• Disconnect power to the appliance before starting any work
• Installation typically requires removing the outer door or control panel; keep fasteners organized
• Handle carefully to avoid scratching the finish and damaging clips or screw bosses

This replacement door handle restores a secure grip and normal door operation on compatible Bosch appliances. It replaces a cracked, loose, or broken handle so the door opens and closes with confidence. What it does:

• Provides a sturdy, ergonomic grip for opening and closing the appliance door
• Replaces damaged, loose, or cosmetically worn handles
• Helps prevent further wear to the door edge and latch area by restoring proper handling
• Matches the original mounting points for a direct-fit replacement on compatible models

• Disconnect power to the appliance before starting any repair
• Retain original mounting screws and brackets; this handle installs using the appliance's factory attachment points
• Support the door while removing/installing the handle to avoid strain on hinges