Speedqueen Awn432sp113 Parts

This washer drain pump removes water from the tub during the drain and spin portions of the cycle. Replacing a failing pump restores proper draining and helps prevent standing water, error codes, and extended cycle times.

• Pumps wastewater out through the drain hose so the washer can complete drain and spin cycles
• Failure symptoms include water left in the tub, slow/no draining, or drain-related error messages
• Also presents as loud humming/grinding from the pump area or leaks around the pump/hose connections
• Restores consistent water removal to help the washer reach and maintain proper spin speeds

• Disconnect power and water supply; bail or drain remaining water and protect the floor
• Access the pump, note hose orientation, and disconnect hoses; if present, unplug the wire harness; remove mounting fasteners
• Transfer any brackets or clamps from the old pump as needed and ensure all hose connections are tight and properly oriented
• After installation, run a drain/spin to check for leaks and proper water removal

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.

This hinge stop clip secures the washer lid hinge to limit travel and keep the lid operating smoothly. Replacing a worn or broken clip restores proper lid alignment and reduces binding or unexpected drops. What it does:

• Limits lid/hinge travel to prevent over-rotation and damage
• Holds the hinge in the correct position for smooth opening and closing
• Helps stop the lid from feeling loose, sagging, or dropping unexpectedly
• Reduces hinge-related noise and uneven lid movement

• Disconnect power to the appliance before beginning any service
• Installation typically requires basic hand tools; handle small metal clips with care
• Align the hinge, then seat or snap the clip into place per the OEM diagram

This water pressure switch detects the washer's fill height and tells the control when the tub has reached the correct water level, helping the machine fill properly and avoid overfilling. What it does:

• Senses water/air pressure from the tub to determine fill level
• Sends a signal to the control to stop filling when the correct level is reached
• Commonly diagnosed when a washer overfills, won't fill, or stops mid-fill
• Works as the water-level safety input for the washer's fill cycle

• Disconnect power and shut off the water supply before starting.
• Note hose and electrical connector locations; remove the vacuum/pressure hose and electrical connector to swap the switch.
• Reinstall hose and connector securely; loose vacuum hose can cause incorrect water-level readings.
• After installation, restore power/water and run a test cycle to ensure proper function.

This drive bell seal kit replaces the bell seal that keeps the washer's transmission and bell housing protected from water intrusion. Restores a watertight seal to help prevent leaks and internal corrosion in top-load washers. What it does:

• Seals the drive bell area to keep wash water out of the transmission and motor cavity
• Helps prevent seal-related leaks that can appear as water under or around the washer
• Reduces risk of internal corrosion and bearing damage caused by moisture
• Addresses symptoms like visible leakage near the base or slow dripping after a cycle

• One drive bell seal

• Disconnect power and water before beginning service
• Access typically requires removing the washer cabinet or rear panel; follow OEM disassembly instructions
• Inspect surrounding components (bell, shaft, gaskets) and clean the sealing surfaces before installing the new seal

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

Replacement bell and transmission tube seal that helps stop leaks where the inner bell meets the transmission on compatible top-load washers. Restores the mating seal to help protect the transmission and keep the wash tub watertight. What it does:

• Seals the joint between the tub bell and transmission to prevent water intrusion
• Helps contain grease or lubricant inside the transmission area
• Reduces risk of transmission damage caused by contamination or fluid loss
• Addresses symptoms such as visible leaks beneath the washer or fluid around the bell housing

• Disconnect power and water supply before beginning service
• Drain the tub and remove the cabinet or access panels as required for your model
• Inspect mating surfaces and replace any damaged gaskets or fasteners for a proper seal
• After installation, run a short test cycle and check thoroughly for leaks

This small sealing washer fits the washer's water pressure assembly to help maintain a proper watertight seal at the pressure/valve connection. Replacing a worn washer reduces leaks and helps the fill/pressure system operate as intended. What it does

• Provides a watertight seal at the water pressure/valve connection to prevent leaks.
• Helps maintain correct pressure feedback to the washer's water control system.
• Wear or damage can allow leaking at the valve or inconsistent fill behavior.
• Simple, low-cost part commonly replaced when troubleshooting valve leaks.

• Turn off household water supply and unplug the washer before replacing.
• Remove the valve/pressure fitting carefully and replace the old washer with the new one, making sure it seats flat and undamaged.
• Inspect mating surfaces for debris or damage; clean before reassembly.
• If leaks or fill issues persist after replacement, inspect related seals, fittings, and the pressure switch/valve assembly.

A replacement cord lead-in that routes incoming power into the appliance and provides a secure connection point for the main wiring. Restores reliable electrical feed and helps eliminate intermittent power or no-power issues. What it does:

• Transfers household power from the external cord to the appliance's internal wiring
• Provides a stable inlet connection and strain relief for the incoming power cable
• Commonly replaced for symptoms such as no power, intermittent power, blown fuses, or visible damage/corrosion at the inlet
• Matches OEM fit and mounting for a direct replacement when the part number is correct

• One cord lead-in assembly

• Disconnect all power at the breaker or unplug the appliance before starting work
• Route wires and secure strain relief per OEM guidance; tighten terminal connections firmly but do not overtighten
• If wiring or terminal damage is present, replace or repair per local electrical code

This insert spline is a splined mating component that restores a secure drive connection inside the washer drive/transmission assembly, helping the machine transfer torque reliably. Replacing a worn spline can reduce slipping and restore proper agitation or spin. What it does:

• Provides the splined interface that transfers rotational force between drive components.
• Replaces a worn or damaged spline that can cause slipping or intermittent drive.
• Helps correct symptoms such as weak agitation, no spin, or grinding/metallic noise during operation.
• Restores proper engagement to reduce wear on adjacent gears and hubs.

• Disconnect power (and water, if applicable) before servicing; follow lockout/tagout and safety guidelines.
• Some disassembly of the cabinet, transmission or agitator hub is required; inspect mating parts for wear and replace as needed.
• Special tools may be needed to press or seat the spline; refer to the manufacturer service manual for correct procedures and torque specs.

This bell-shaped plug seals an access opening to protect internal components from water, lint, and debris. It provides a simple replacement to restore a watertight/clean barrier and help prevent moisture-related damage. What it does:

• Seals a bell-shaped access or service opening to keep moisture and debris out
• Restores a worn or missing plug that can allow leaks or contamination
• Helps maintain proper cabinet/tub protection and part performance
• Simple push-in design for a snug, reusable seal

• Disconnect power and shut off water before servicing
• Inspect the mating surface and clean debris before installing the plug
• Press firmly into the opening until fully seated; use a light lubricant (soap or silicone) if needed for tight fits
• Do not force or hammer; replace if plug or surrounding sealing surface is damaged

Self clean

A size #20 hose clamp used to secure flexible hoses to fittings on laundry appliances, helping prevent leaks and keep hoses firmly attached during operation. Simple, low-profile design for reliable hose connections. What it does:

• Secures washer drain and inlet hoses to fittings to reduce leak risk.
• Prevents hoses from slipping off under pressure or vibration.
• Helps maintain consistent water flow by keeping connections tight.
• Fits standard #20 hose diameter applications commonly used on laundry equipment.

• One size #20 hose clamp.

• Use a flathead screwdriver or nut driver to tighten; turn until snug—do not overtighten to avoid hose damage.
• Inspect hose and fitting for cracks or corrosion and replace if needed before installing the clamp.
• After installation, run a short test cycle and check for leaks; retighten if necessary.
• Disconnect power and water supply before servicing the appliance.

This wave washer is a spring-style spacer used in washer assemblies to apply tension and maintain proper spacing. It controls endplay so parts fit securely and the machine runs smoothly with reduced vibration and noise during wash and spin cycles.

• Provides spring preload to maintain correct spacing in rotating assemblies
• Helps limit endplay that can cause rattling, chatter, or intermittent engagement
• Can help address symptoms like metallic noises, excessive play/wobble, or rough operation during agitation or spin
• Replace if the original washer is flattened, cracked, or missing

• Disconnect power and turn off water before servicing
• Note the exact stack order and orientation of spacers/shims during disassembly
• Install the new wave washer in the same orientation; do not bend or deform it
• Reassemble and hand-rotate components to check for smooth operation before test-running

This tall-lip seal fits the outer tub to help keep wash water inside the tub and protect internal components from leaks. It replaces a worn or damaged outer tub seal to restore a watertight tub interface. What it does:

• Provides a watertight seal between the outer tub and adjacent components
• Helps prevent water leaks that can cause floor damage or electrical issues
• Reduces noise and vibration caused by an improperly sealed tub
• Commonly replaced when you see visible seal wear, cracking, or recurring leaks

• One tall-lip outer tub seal (seal pack) as specified by the manufacturer

• Disconnect power and water supply before starting any repair
• Inspect mating surfaces and clean away residue before installing the new seal
• Some models may require partial disassembly of the cabinet or tub; follow the OEM service manual