Srv 53M03 Eu/12 Parts

This is the left side hinge plate. For right side use 00298570.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This is the front corner block. For rear corner block use 00263093.

The Hinge Rope is an OEM replacement part for Bosch dishwashers. It serves as a flexible hinge, enabling smooth and controlled opening of the dishwasher door. Proper torsion and tension of the hinge rope allow for easy loading and unloading while keeping the door securely closed during operation. 

Causes of a bad hinge rope include cuts, abrasions, or weakened fibers developing over extensive use cycles. Moisture exposure could potentially degrade material integrity if not properly dried.

Symptoms of a bad hinge rope include:

• Difficulty smoothly opening or closing the door  
• The door unable to securely latch or lock into position
• Excessive sagging causes the door to hang unevenly  
• Rope fibers protruding or frayed edges developing

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This inlet seal is a small rubber gasket that creates a watertight connection at the dishwasher's water inlet. Replacing a worn seal helps stop leaks and ensures the inlet valve can fill the appliance properly. What it does:

• Seals the water inlet connection to prevent drips or steady leaks underneath the dishwasher
• Maintains a tight seal at the inlet valve so the fill cycle can operate normally
• Commonly replaced when there is visible wear, cracking, or persistent water on the floor
• Helps avoid water damage and the nuisance of repeated drainage or fill errors tied to leaking

• One inlet seal

• Turn off the water supply and disconnect power before servicing
• Remove the inlet valve or access panel as needed to reach the seal; replace with the old seal removed
• Make sure the new seal is seated evenly and the mating surfaces are clean before reassembly

This replacement rubber seal creates a watertight barrier between mating parts to help prevent leaks and preserve normal appliance operation. It restores sealing performance where an old or damaged seal is letting fluid escape. What it does:

• Provides a flexible, water-resistant seal between joined components to stop leaks
• Cushions mating surfaces to reduce wear and vibration at the joint
• Maintains proper fluid containment and pressure at the sealing interface
• Common symptom addressed: visible leaks or drips near a connection or joint

• Disconnect appliance from power and shut off water before beginning work
• Remove the old seal and thoroughly clean and dry the mating surfaces before installing the new seal
• Seat the replacement evenly around the entire perimeter; avoid twisting or pinching the material
• After installation, restore power/water and run a short cycle or test to confirm there are no leaks

This is the rear corner block. For front corner block use 00263094.