Sts16abserww Parts

This control knob fits onto the control shaft to let you adjust settings on your refrigerator. Replacing a cracked or missing knob restores smooth adjustments and keeps the control easy to use.

• Attaches to the control shaft to select temperature/settings
• Common fix for a knob that is cracked, stripped, loose, or missing
• Helps when the knob spins without engaging the shaft or falls off
• Restores proper feel for everyday adjustments

• Unplug the refrigerator before working near the control area
• Pull the old knob straight off—avoid prying on the panel
• Align the flat/D-shaped opening with the shaft and press firmly until seated
• If the knob won't seat, inspect the control shaft for damage before forcing

This compressor overload protects the refrigerator's compressor by interrupting power when it overheats or draws excessive current. Replacing a weak or failed overload can stop repeated click/no-start symptoms and help restore normal cooling performance.

• Opens the circuit to protect the compressor during overheat or over-current conditions
• Automatically resets after cooling to prevent sustained damage
• Symptoms include: compressor won't start, rapid clicking from the compressor area, starts then stops, and a warm refrigerator/freezer
• Helps prevent motor and wiring damage caused by repeated overload events

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment and remove the compressor/start device cover
• Note wire positions; pull the old overload straight off the compressor terminal and push the new one on fully seated; reconnect wiring and covers
• If the overload trips again after replacement, further diagnosis of the start relay, run capacitor, or compressor may be required

This front shelf end cap replaces the right-hand piece that anchors the refrigerator shelf's front trim/rail. A secure cap keeps the front edge supported so the trim stays in place and the shelf remains stable.

• Retains the front shelf trim/rail on the right-hand side
• Supports the shelf's front edge to help prevent sagging
• Replaces a cracked, worn, or missing cap
• Common symptoms: trim won't stay attached, loose or wobbly front edge, visible damage to the cap

• Unplug the refrigerator and remove the shelf before servicing
• Handle glass shelves carefully; support both sides to avoid breakage
• Right-hand is determined when facing the shelf from the front; RH is not interchangeable with LH
• Align tabs/slots with the trim and shelf frame; press or snap fully into place, then reinstall the shelf

This U-shaped clip secures trim and components in place on compatible GE appliances, helping keep panels and assemblies aligned for reliable operation. Simple replacement when a broken or missing clip causes loose trim or rattling. What it does:

• Holds trim, panels or small assemblies in position to prevent movement
• Restores secure fit where a worn or broken clip allows gaps or vibration
• Helps eliminate rattling, misaligned doors, or loose internal components
• Works as a direct-fit replacement for the same OEM clip design

• One U-shaped retaining clip

• Turn power off and unplug the appliance before accessing panels or parts
• Remove any trim or screws carefully to reach the clip location; retain fasteners
• Clip typically snaps into place; replace any damaged surrounding hardware

This plastic extension fill tube continues the water path from the valve to the ice maker, restoring proper water delivery for ice production. It helps ensure the ice maker receives measured water without leaks or misdirection. What it does

• Extends the water fill line to reach the ice maker inlet and maintain proper fill height
• Directs metered water into the ice maker mold to form full, solid ice cubes
• Commonly replaces cracked, kinked, or detached tubing that leaks or reduces fill
• Helps stop intermittent or no-fill symptoms when the ice maker and valve are otherwise working

• One plastic extension ice maker fill tube

• Disconnect power and shut off the water supply before starting work
• Remove only panels or components necessary to access the ice maker and fill tube
• Securely seat tubing on the valve and ice maker inlet; check for kinks or contact with sharp edges
• Test for leaks and proper fill by restoring power and water, then observing one fill cycle

This top hinge and pin assembly secures the refrigerator door to the cabinet and provides a durable pivot point for smooth opening and closing. Replacing a worn hinge restores proper door alignment and sealing. What it does:

• Supports the top of the door and transfers weight to the cabinet frame
• Provides the pivot pin for consistent, smooth door movement
• Helps maintain proper door alignment and a tight seal to prevent cool-air loss
• Can resolve symptoms such as door sagging, uneven gaps, rubbing, or noisy hinge operation

• Disconnect power and remove food from door area before starting repair
• Support the door to prevent dropping or damage during hinge removal
• Keep track of mounting hardware and orientation for correct reinstallation; follow the appliance manufacturer's service instructions
• Do not force or overtighten fasteners; check door alignment and operation after installation

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

This white corner cap is a small plastic cover that snaps onto a refrigerator door corner to protect the hinge area, conceal fasteners, and restore a finished appearance. Simple replacement for visible damage or missing trim. What it does:

• Covers and protects the door corner and hinge area from dirt and damage
• Hides exposed screws and hardware for a cleaner look
• Prevents sharp edges or gaps that can catch clothing or fingers
• Commonly replaced when cracked, broken, or missing after impact or wear

• Snaps into place
• No wiring; no disassembly beyond removing the damaged cap in most installs
• Disconnect power only if you must remove nearby electrical components; otherwise work with the appliance idle
• Handle plastic parts carefully to avoid cracking; do not force into place

This clip retainer secures trim, panels, or wire harnesses to keep components stable and reduce noise or wear. It's a small but important fastener that helps maintain proper fit and routing inside the appliance. What it does:

• Secures wiring or harnesses to prevent rubbing, pinching, or strain that can cause intermittent connections
• Holds panels and trim in place to reduce vibration and rattling during operation
• Keeps components aligned for reliable door/trim fit and proper clearance
• Helps prevent wear on insulation and nearby parts by keeping parts stationary

• Disconnect power before servicing to avoid shock or injury
• Remove trim or access panels as needed to reach the damaged clip
• Replace the broken clip with the new retainer; ensure the harness or panel is seated correctly in the clip
• Replace them to ensure secure reassembly

For metal hinge pin use part number WR02X27092