Swnsx2p115ytw02 Parts

A size #20 hose clamp used to secure flexible hoses to fittings on laundry appliances, helping prevent leaks and keep hoses firmly attached during operation. Simple, low-profile design for reliable hose connections. What it does:

• Secures washer drain and inlet hoses to fittings to reduce leak risk.
• Prevents hoses from slipping off under pressure or vibration.
• Helps maintain consistent water flow by keeping connections tight.
• Fits standard #20 hose diameter applications commonly used on laundry equipment.

• One size #20 hose clamp.

• Use a flathead screwdriver or nut driver to tighten; turn until snug—do not overtighten to avoid hose damage.
• Inspect hose and fitting for cracks or corrosion and replace if needed before installing the clamp.
• After installation, run a short test cycle and check for leaks; retighten if necessary.
• Disconnect power and water supply before servicing the appliance.

This cycle selector switch restores precise, reliable cycle selection. Mounted behind the control panel, it communicates the chosen setting to the timer or control so the machine starts and runs the intended program.

• Selects the desired cycle and closes the correct contacts for that setting
• Works with the timer/control to initiate and run the chosen cycle
• Helps resolve: cannot select or change cycles; knob turns without engagement
• Helps resolve: unit won't start a cycle, runs only one cycle, or selects intermittently

• Disconnect power before servicing
• Access the control console; remove knob/retainer and mounting hardware to release the switch
• Note or photograph wire locations; transfer connectors to the new switch one at a time
• Secure the switch, reassemble the console, restore power, and test cycle selection

This tall-lip seal fits the outer tub to help keep wash water inside the tub and protect internal components from leaks. It replaces a worn or damaged outer tub seal to restore a watertight tub interface. What it does:

• Provides a watertight seal between the outer tub and adjacent components
• Helps prevent water leaks that can cause floor damage or electrical issues
• Reduces noise and vibration caused by an improperly sealed tub
• Commonly replaced when you see visible seal wear, cracking, or recurring leaks

• One tall-lip outer tub seal (seal pack) as specified by the manufacturer

• Disconnect power and water supply before starting any repair
• Inspect mating surfaces and clean away residue before installing the new seal
• Some models may require partial disassembly of the cabinet or tub; follow the OEM service manual

This is a 1/4-15 x 3/4 hex head screw used to secure components in laundry appliances. It provides a strong, threaded fastening point for panels and brackets so parts stay properly aligned during operation. What it does:

• Fastens panels, brackets, or components where a 1/4-15 x 3/4 hex head screw is specified
• Holds assemblies securely to reduce vibration and movement
• Can be used to replace a worn, stripped, or missing screw to restore proper fit
• Matches OEM thread and length for correct engagement when used as specified

• One 1/4-15 x 3/4 hex head screw

• Disconnect power to the appliance before performing any repairs
• Use the correct hex driver/socket to avoid rounding the head
• Tighten snugly but avoid over-torquing to prevent stripping threads or cracking components
• Replace with the exact part if damaged;

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This is a 1/4-20 x 9/16 hex flange screw used to secure panels and assemblies on commercial and residential laundry equipment. It provides a durable, threaded fastener that restores proper fit and prevents rattling or loose components. What it does:

• Fastens panels, brackets, and components where a 1/4-20 hex flange screw is specified
• Replaces stripped, corroded, or missing screws that cause loose parts or vibration
• Restores secure connections that can reduce noise and align panels
• Used in areas requiring a flange head for wider bearing surface and resistance to loosening

• One 1/4-20 x 9/16 hex flange screw

• Install with the correct size hex driver or socket; avoid over-tightening to prevent stripping
• Replace any damaged or corroded mating hardware as needed for secure fit
• Disconnect power and follow safety procedures if working near electrical components

This replacement porcelain touch-up paint restores small chips, scratches and worn spots on enamel-coated appliance surfaces to help improve appearance and slow surface corrosion. Easy to apply for spot repairs. What it does:

• Covers small chips, scratches and scuffs on porcelain/enamel surfaces
• Helps protect exposed metal from moisture that can lead to surface rust
• Matches factory finish color on compatible porcelain-coated panels (spot repairs only)
• Useful for finishing edges around dings and improving visual appearance

• One bottle of porcelain touch-up paint

• Clean and dry the repair area thoroughly; remove loose paint and rust before applying
• Test paint in an inconspicuous spot to confirm color match and adhesion
• Apply sparingly with a fine brush or applicator; allow recommended drying time between coats
• Keep away from open flame; store and dispose of per local regulations; keep out of reach of children

Replacement washer lid with service label that restores the top cover and visible service information on compatible Speed Queen top-load washers. Provides a clean, secure cover to protect controls and internal parts while displaying service details. What it does:

• Replaces a cracked, dented, or corroded top lid to restore proper fit and appearance.
• Restores the factory service label/location used for service instructions and part identification.
• Protects internal components and control assemblies from debris and accidental contact.
• Helps the lid latch and open/close smoothly when the original is damaged or bent.

• Disconnect power to the washer before starting any repair.
• Use proper tools and keep track of screws/fasteners; inspect hinge and latch for wear and replace if needed.
• Handle edges carefully; some lids have sharp metal edges or trim.
• After installation, verify lid alignment and that the lid opens, closes, and latches correctly before returning the washer to service.