Thermador Phe 38 Parts

This cover fits on the bottom of the refrigerator ice bucket to protect the bucket base and help keep ice contained for smooth dispensing. Replaces a cracked, warped or missing bucket bottom cover to restore proper ice handling. What it does:

• Replaces the bottom cover of the ice bucket to protect the bucket base and help keep ice from spilling.
• Helps stop rattling or scraping noises caused by a damaged or loose bucket bottom cover.
• Prevents exposed bucket edges that can catch or break ice during removal.
• Useful when you see visible cracks, deformation, or gaps at the bucket base.

• One cover bucket bottom

• Disconnect power to the appliance before starting any repairs.
• Remove and empty the ice bucket before replacing the cover to avoid injury and spills.
• Handle the cover and surrounding parts carefully—sharp edges may be present.
• Reinstall the cover securely and test ice removal to confirm proper fit.

A replacement dispenser wire actuator that engages the door-mounted water/ice dispenser when pressed, restoring reliable lever operation and user control at the refrigerator door. Matches OEM form and function for dispenser activation. What it does

• Transfers user pressure from the dispenser lever to the valve/actuator assembly so water or ice is dispensed.
• Replaces bent, broken, or loose actuator wire that causes intermittent or no dispensing.
• Helps restore a positive lever feel and consistent dispenser response.
• Safe, low-voltage mechanical linkage — not an electrical control.

• One dispenser wire actuator (single lever wire).

• Unplug or disconnect refrigerator power before beginning any repair to avoid electrical hazard.
• Basic door panel removal may be required; handle trim and clips carefully to avoid damage.
• Align the wire with the dispenser lever and secure per OEM mounting—do not force or bend excessively.

This replacement water filter cover restores the exterior trim that secures and protects the refrigerator's water filter, keeping the filter seated and helping prevent debris or light leaks around the filter area. What it does:

• Covers and secures the water filter housing so the filter stays properly seated
• Protects the filter from dirt and accidental contact
• Helps maintain a finished appearance at the filter access point
• A damaged or missing cover can allow the filter to shift or create visible gaps at the housing

• Turn off the water supply and follow refrigerator power/safety instructions before servicing
• Remove the old cover by releasing any clips or screws, then snap or fasten the replacement into place
• Verify the filter is properly seated and check for leaks after restoring water/power

This water filter cover protects and secures the refrigerator's inline filter assembly while keeping the filter compartment sealed and tidy. It helps ensure a proper fit so the filter can seat correctly and water flows as intended. What it does:

• Replaces a cracked, broken or missing water filter cover to restore proper filter seating and alignment
• Helps prevent leaks by maintaining the cover seal around the filter area
• Keeps the filter compartment clean and prevents debris from entering the housing
• Supports correct water flow and helps avoid dispensing problems caused by a loose or damaged cover

• One water filter cover

• Disconnect power and turn off the refrigerator water supply before servicing
• Remove the old cover and gently snap or screw this cover into place per your model's mounting points
• Hand-tighten fasteners; do not overtighten plastic clips or screws
• After installation, restore power and water, check for leaks, and run a few cycles to confirm proper seating

This dispenser housing shield replaces the trim piece that surrounds and protects the refrigerator's ice/water dispenser opening, restoring appearance and keeping dispenser components covered. Fits the factory mounting points for a direct fit. What it does:

• Covers and protects dispenser controls and internal components from spills, debris, and accidental impact.
• Guides dispensed water/ice into the cup area to reduce splashing.
• Prevents drafts and minimizes cold air loss around the dispenser opening.
• Worn, cracked, or loose shields can cause visible damage, wobbling, or allow debris into the dispenser area.

• One dispenser housing shield

• Disconnect power and shut off water to the refrigerator before beginning service.
• Typically installs behind the dispenser bezel or front panel; some models require removing the dispenser trim or control panel first.
• Retain all screws and clips from the original part; use only the specified fasteners for reassembly.

This wiring harness connects and supplies power to the dispenser motor so the dispenser operates reliably. It replaces a worn or damaged dispenser motor harness to restore electrical continuity and dependable dispenser function. What it does:

• Carries voltage and signals between the control and the dispenser motor
• Restores power when a broken or frayed harness prevents the motor from running
• Helps stop intermittent dispenser operation caused by loose or damaged wiring
• Provides proper connector fit to maintain a secure electrical connection

• Disconnect power to the appliance before inspecting or replacing the harness
• Handle connectors gently and verify correct orientation before mating
• Route harness following original wire paths and secure with existing clips to avoid pinching
• If corrosion or other damaged components are present, inspect surrounding parts and replace as needed