Tq1br3w Parts

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 8-32 x .312 inch.

This screw secures appliance panels and components to keep assemblies stable and aligned during normal use. It's a direct-fit fastener used where the factory requires a specific screw shape and thread. What it does:

• Fastens trim, panels, brackets, or internal components to the cabinet or frame
• Restores secure mounting when original fasteners are missing or stripped
• Helps eliminate rattling, vibration, or loose parts caused by a missing screw
• Matches OEM fit and fastening points for correct assembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace only the damaged or missing screw; confirm orientation and thread engagement before final tightening
• Disconnect power and follow all safety precautions before servicing appliances

This start relay controls power to the compressor's start winding so the refrigerator can start and run. Replacing a weak or burned relay restores dependable compressor start-up and can stop repeated clicking with warming temperatures.

• Energizes the compressor's start winding to provide initial torque, then disengages from the circuit
• Common failure symptoms: refrigerator not cooling or intermittently warm; compressor hums/clicks and won't start; relay rattles, smells burnt, or shows heat damage; overload trips
• Helps prevent hard-start conditions that stress the compressor
• The relay contacts are open/shorted, the compressor may fail to start and cycle off on overload

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment; remove the relay cover on the compressor. Note wire positions, pull the old relay straight off the compressor pins, transfer wires, and fully seat the new relay in the same orientation
• If equipped, safely discharge the run capacitor; inspect the overload, wiring, and terminals for heat damage and address as needed
• Reinstall the cover. If the compressor still won't start, further diagnosis of the start device, capacitor, or compressor is required

This evaporator fan motor drives the internal fan that circulates cold air across the evaporator coils and throughout the refrigerator. Replacing a weak or noisy motor restores proper airflow for more consistent temperatures and reliable cooling. What it does

• Moves air across the evaporator coils to remove heat from the cabinet
• Distributes chilled air to both compartments for even cooling
• Helps reduce warm spots and temperature swings
• Common symptoms: fan not running, weak airflow from vents, louder-than-normal or intermittent fan noise, warmer-than-usual refrigerator or freezer

• One evaporator fan motor

• Disconnect power to the appliance before servicing
• Access the motor behind the rear panel inside the freezer; remove shelves/drawers as needed
• Transfer the existing fan blade, grommets, and bracket if required; mount the new motor in the same orientation
• Reconnect the wire harness, ensure the blade spins freely, reassemble panels, restore power, and confirm the fan runs

Single

A replacement door gasket that restores a tight seal around the oven door to help maintain proper cooking temperature and improve efficiency. Fits Whirlpool ovens and ranges that use part A3189394. What it does

• Seals the oven cavity to reduce heat loss and help maintain consistent cooking temperatures.
• Helps prevent heat from escaping around the door, improving energy use and cook results.
• Worn, torn, or flattened gaskets can cause uneven baking or longer cook times.
• Replacing a damaged gasket can reduce hot spots on the exterior and nearby cabinetry.

• Disconnect power and ensure the oven is completely cool before starting.
• Remove the old gasket by pulling it out of the door channel; clean the channel before installing the new gasket.
• Press the new gasket into the channel around the full perimeter, working from one corner and ensuring an even fit.

This replacement screw fastens internal components and panels so parts stay secure and quiet. It's a direct-fit fastener used where the original mounting screw is missing or damaged to restore proper assembly. What it does:

• Secures panels, brackets or components to prevent movement and vibration
• Restores proper alignment for covers and access panels
• Stops rattling or loose-fitting parts caused by a missing or stripped screw
• Works as the factory-specified fastener for the original mounting point

• The screw location and type before installing; use the original hole and thread
• Power off and disconnect the appliance before accessing internal components
• Start the screw by hand to avoid cross-threading, then snug with the appropriate screwdriver
• Do not overtighten — stop once the part is secure to avoid stripping or cracking

This elbow drain tube redirects drain water through a tight 90° turn to the appliance drain path, restoring proper drainage and preventing leaks from cracked or damaged tubing. A direct-fit replacement for worn or broken drain elbows. What it does

• Guides wastewater from the pump or internal drain outlet into the drain hose or drain channel
• Restores a secure, leak-free connection when the original elbow is cracked, split or deformed
• Helps maintain proper flow by providing a smooth, angled transition that reduces kinking
• Commonly replaced when you see leaks, visible damage, or poor drainage

• One elbow drain tube

• Disconnect power and water before starting any repair
• Remove access panels as needed to reach the original elbow; replace with the new elbow in the same orientation
• Ensure all clamps or retaining tabs are secured to prevent leaks; test with a short water/run cycle