Waw6400sw2 Parts

This hose inlet is the dishwasher water-connection fitting that routes incoming water into the appliance. It provides a secure connection to help prevent leaks and ensure consistent water supply for normal wash cycles. What it does:

• Connects the household water supply to the dishwasher's internal water system
• Seals the inlet to help prevent drips or leaks at the connection point
• Ensures the appliance receives steady water flow for proper filling and operation
• Be replaced when the inlet is cracked, corroded, or leaking

• Disconnect power and shut off the water supply before starting any work
• Inspect and replace any worn O-rings or gaskets when installing the new inlet
• Hand-tighten fittings and then check for leaks; retorque per OEM guidance if available

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation

A replacement drain hose that routes wastewater from the dishwasher tub to the household drain. Replacing a damaged or clogged drain hose restores proper draining, helps prevent standing water and reduces the risk of leaks. What it does:

• Channels wastewater from the dishwasher to the home drain so cycles can finish without leaving water in the tub.
• Provides a sealed path to prevent leaks under the appliance; cracks or splits can cause puddles or floor damage.
• Flexible routing helps avoid kinks and obstructions; a blocked or pinched hose can cause slow draining or drain-related error codes.

• Disconnect power and water supply before starting any work.
• Remove the lower access panel or toe kick to access the hose and note original routing before removal.
• Reconnect using the existing clamps or appropriate replacement clamps; ensure fittings are seated and secured to prevent leaks.
• Run a short drain cycle and inspect all connections and surrounding areas for leaks.

This is a factory replacement set packaged under this part number. It provides matched components specified by the manufacturer to restore proper fit and function when the original set pieces are worn, missing, or damaged.

• Supplies the exact grouped parts designated for this repair
• Helps resolve issues caused by missing, loose, or broken components
• Supports correct assembly, alignment, or sealing as designed
• Common signs include rattling, misalignment, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Refer to your model's parts diagram for placement and orientation
• Handle sharp edges/components carefully; wear cut-resistant gloves
• Verify operation before final reassembly

This replacement flap restores proper operation by sealing or guiding an opening within the appliance assembly. Replacing a damaged flap helps maintain correct movement and alignment, preventing nuisance rattles and performance issues in the related area. What it does:

• Covers or seals an opening, chute, or compartment to maintain proper function
• Guides airflow, water, or items as designed within the assembly
• Hinges/snaps to allow controlled opening and closing
• Typical failure symptoms: cracked or broken plastic, flap won't stay closed, poor sealing, noise or misalignment in the affected section

• 1 flap

• Disconnect power and, if applicable, shut off water before servicing
• Wear cut-resistant gloves; edges and surrounding metal/plastic may be sharp
• Note the original orientation and hardware; take a quick photo before removal
• After installation, verify the flap moves freely and seals/aligns as intended

This dispenser tray is the dishwasher detergent cup assembly that holds and releases detergent during wash cycles, helping ensure detergent is delivered when the machine rinses and cleans dishes. What it does

• Holds detergent/soap and releases it at the correct point in the wash cycle
• Ensures proper detergent flow to improve cleaning performance
• Prevents loose detergent from scattering inside the tub
• Visible replacement sign: cracked, warped, or detergent residue that won't clear

• One dispenser tray (detergent cup) as shown

• Disconnect power and water supply before removing or installing the dispenser
• Remove the inner door panel per manufacturer instructions to access the tray
• Handle carefully to avoid damaging the door latch and wiring harness
• Run a short test cycle after install to confirm proper operation and detergent release

This fixing kit supplies the mounting and fastening hardware used to secure appliance components during installation or repair, helping restore proper fit and reduce vibration or loose panels. Ideal for replacing missing or damaged fasteners. What it does

• Provides the specific screws, clips, and brackets used to anchor panels or assemblies
• Stops rattling and vibration caused by loose or missing mounting hardware
• Restores proper alignment of doors, panels, or internal components
• Replaces worn or corroded fasteners that can compromise a secure fit

• Disconnect power and water before beginning any repair work
• Use proper tools and follow the appliance manufacturer's installation instructions
• Inspect surrounding components and mounting surfaces; replace any damaged parts

This cable supply is the factory replacement power harness that connects the appliance's control and motor assemblies to the power source, restoring proper electrical connection and reliable operation. Fits as a direct OEM replacement. What it does

• Carries electrical power from the main supply to the appliance control and motor circuits.
• Replaces damaged, frayed, or intermittent wiring that can cause power loss or erratic operation.
• Helps resolve symptoms such as no power to controls, intermittent cycling, or components not running.
• Restores secure terminals and connector fit for consistent electrical contact.

• One replacement cable supply (power harness) as shown.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Inspect connector ends and routing; install in the same orientation and secure any strain reliefs or clips.
• If routing through panels or grommets, ensure wires are not pinched and have appropriate clearance from heat sources.

This cable harness routes power and signals between appliance components to restore electrical connections and reliable operation. It replaces damaged or worn wiring that can cause intermittent power, non-responsive controls, or component failures. What it does:

• Provides the factory wiring path and connector interfaces for the appliance's control and powered parts
• Restores proper electrical connections when wires are frayed, broken, or connectors are loose
• Helps stop intermittent power, control errors, or components that won't run due to wiring faults
• Matches OEM connector types and lengths to ensure correct fit and function

• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Verify connector orientation and secure all plugs; route wires per service manual to avoid heat or moving-part contact
• Inspect mating connectors and terminals for corrosion or damage before installation

This flexible inlet/fill hose routes water into the appliance, restoring proper water delivery for normal operation. Replace a damaged hose to stop leaks and ensure reliable water flow. What it does:

• Carries incoming water from the supply to the appliance fill assembly
• Prevents water leaks when intact; a cracked or split hose can cause pooling or drips
• Restores normal fill behavior when worn or collapsed hoses reduce flow
• Works with clamps or fittings at each end to create a watertight seal

• One flexible inlet/fill hose

• Turn off the water supply and disconnect power before removing the old hose
• Inspect and replace any worn clamps, gaskets, or fittings for a secure seal
• Hand-start fittings, then tighten with tools—avoid over-tightening to prevent damage
• After installation, restore water and power, then run a short cycle and check for leaks

This door lock assembly secures the appliance door during operation so cycles can run safely and reliably. It replaces a worn or broken latch to restore proper door closure and locking action. What it does:

• Secures and latches the appliance door so the unit can start and run
• Prevents the door from opening mid-cycle, reducing leaks and interruptions
• Common fix for door-not-locking, door won't stay closed, or related error codes
• Works as the mechanical/electrical interface that detects a closed door

• Disconnect power before beginning any repair to avoid shock
• Handle carefully; avoid forcing the latch or twisting mounting tabs
• Verify correct orientation and engage mounting screws securely but not overtighten

This upper dispenser tray holds and positions detergent and rinse aid cups in the dishwasher door so detergents release correctly during the wash cycle. Fits upper-door dispenser assemblies to restore proper dispensing and cleaner wash results. What it does:

• Provides the correct mounting and alignment for detergent and rinse-aid cups during cycles
• Ensures detergent doors open and close reliably for measured release
• Helps prevent detergent residue from spilling into the tub when closed
• Commonly replaces cracked, warped, or damaged trays that cause poor dispensing

• One upper dispenser tray

• Designed for replacement inside the dishwasher door; access typically requires removing the inner door panel
• Disconnect power and water to the appliance before beginning any repair
• Inspect dispenser actuator and springs while replacing the tray and replace any worn components