Wcvh4800kww Parts

This heater thermistor is a temperature-sensing replacement part that helps the appliance monitor and regulate heating. Replacing a failed thermistor restores accurate temperature feedback for safer, more consistent operation. What it does

• Measures temperature near the heater and sends a signal to the control board.
• Helps the unit cycle heating on and off to maintain proper operating temperature.
• Common symptom: appliance won't heat or heats intermittently.
• Common symptom: cycles too frequently or shows error codes related to temperature sensing.

• One heater thermistor.

• Disconnect power before accessing or replacing the thermistor.
• Handle the sensor and connector carefully to avoid damage to the lead or plug.
• Verify connector orientation and secure wiring; do not force connectors.

The Door Gasket is an OEM part for GE washing machines. Located around the washer door opening, it creates a tight seal during cycles to prevent water leaks.   

Symptoms of a bad door gasket include:

• Water leaks from the washer door opening  
• Excess moisture buildup or puddling near the door
• Inability to achieve proper seal for optimal washing

Causes for failure can be cracks, perforations, or deteriorated material from repeated use and mechanical stresses over time. Mineral or soap deposits may also degrade sealing properties.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This basket assembly is a genuine OEM replacement part sourced directly from the manufacturer for use in front-load washing machines. This assembly is part of the washer's drive system. It is on top of the clutch and transmission system. It contains the spin tube shaft and brake system for the spin basket. If the washing machine is making loud noises during the spin cycle or won't spin at all, the basket assembly should be replaced. A screwdriver, socket wrench set and ratchet, hammer, and spanner wrench are needed to make this repair. Disconnect the water and power to the washing machine. Wear work gloves when making these repairs. Make sure the machine is pulled away from the wall, and there is plenty of room to work while disassembling the machine. Remove the top console and then the washing machine cabinet. Take the tub ring and agitator off the machine. Remove the spin basket and drive block and release the drive block. Remove and replace the basket drive. Reverse the order and reassemble the washing machine. Reconnect the power and water. This basket assembly is sold individually. It is designed for washing machines manufactured by General Electric.

A self-tapping screw used to fasten appliance panels and components where a threaded hole is formed as the screw is driven. Provides a secure hold for trim, brackets, and light assemblies during repairs. What it does:

• Cuts its own mating thread in sheet metal or thin plastic to secure panels and brackets
• Helps hold trim, access panels, or internal components in place
• Commonly used where a tapped hole is not present or repair requires a replacement fastener
• Can prevent loose parts and rattles caused by missing or damaged screws

• Unplug the appliance before servicing to avoid electrical or mechanical hazards
• Use the correct screwdriver or bit to avoid stripping the screw head
• Start the screw straight and apply steady pressure; do not overtighten to avoid cracking plastic or stripping metal
• Replace only with the exact part number to ensure proper fit and function

This drawer dispenser assembly replaces a damaged or worn dispenser drawer to restore secure containment and reliable dispensing in your appliance. It helps keep detergents or dispensing components properly housed and prevents leaks or jams. What it does:

• Holds the appliance's dispenser drawer securely in place during use
• Guides and releases detergent or dispensing materials as designed
• Stops leaks or drips caused by cracked, warped, or broken drawer parts
• Prevents binding or sticking of the dispenser drawer for smooth operation

• Disconnect power and water before beginning any repair
• Remove the drawer or access panel per the appliance service instructions before installing
• Handle plastic components carefully to avoid cracking; use appropriate tools and gentle force

This door switch is a replacement push-button switch that completes the circuit when the appliance door closes, restoring power or lighting. It helps return normal operation when a faulty door switch prevents the unit from running or the interior light from working. What it does:

• Detects door open/closed position and completes or interrupts power to controls or lights
• Commonly replaces a broken or non-responsive push-button that prevents the appliance from starting
• Fits into the door frame and connects to the existing wiring harness to signal closed/open status

• One door switch (WH12X10444)

• Disconnect power (unplug or shut off breaker) before attempting any service
• Remove the door trim or access panel as required for your model to reach the switch mounting
• Note wire locations or take a photo before disconnecting; reattach wires to the same terminals

This spring suspension supports the washer tub to help maintain drum alignment and reduce vibration during spin cycles. Replacing a worn spring restores stability and helps cut down on banging, rocking, and excessive movement. What it does:

• Holds the tub in position and absorbs shocks during wash and spin cycles.
• Helps prevent the drum from contacting the cabinet or standing unevenly.
• Commonly replaced when the washer rocks, bangs loudly during spin, or the tub sags.
• Works as a direct suspension component—matches OEM function and placement.

• Disconnect power and turn off the water supply before starting any repairs.
• Relieve tension by supporting the tub or cabinet frame; replace springs one at a time to maintain alignment.
• Use appropriate hand tools (pliers, nut drivers) and wear gloves and eye protection.
• Inspect related suspension components and replace any additional worn parts for best results.

This tub front is the front bulkhead that supports the dryer drum and front drum seal, restoring proper drum alignment and helping reduce rubbing, squeaks, and wear on rotating components. What it does:

• Supports the dryer drum at the front and provides a mounting surface for the front drum seal.
• Keeps the drum centered to allow smooth, even tumbling.
• Prevents clothes from catching or rubbing on the cabinet by maintaining correct drum clearance.
• Commonly replaced when the front surface is cracked, warped, or the seal area is damaged, causing noise or rubbing.

• One tub front (front bulkhead) as shown.

• Disconnect power to the appliance before starting any repair.
• Replacement typically requires removing the dryer front panel and drum; keep fasteners and note seal orientation.
• Use basic hand tools; some models may require lifting the drum slightly to set the tub front.
• If seals, bearings, or felt guides are worn, replace them at the same time for best results.

A replacement control knob assembly that restores safe, positive control of your appliance's settings. Replaces a cracked, stripped, loose, or missing knob so you can select functions and settings reliably. What it does:

• Provides a secure grip and smooth rotation for selecting temperature or function settings
• Replaces knobs that are cracked, worn, stripped, loose, or missing
• Restores proper control engagement when the original will not turn or won't stay set
• Matches OEM fit and mounting for a straightforward swap

• Always disconnect power to the appliance before starting any repair
• Most installations are push-on: remove the old knob by pulling straight off, then push the replacement onto the control shaft until fully seated
• If the knob is tight or stuck, gently wiggle while pulling; avoid prying on surrounding surfaces

This pressure switch detects and signals water level to the washer control so cycles fill and stop correctly. Replaces a failed level sensor to restore accurate fill control and prevent overfilling or incorrect cycle behavior. What it does

• Senses tub water level via a vacuum hose and tells the control when to stop filling
• Helps prevent overfilling, underfilling, or prolonged fill cycles
• Can cause no-fill, continuous-fill, or incorrect cycle problems when faulty
• Works as the electrical interface between the pressure/vacuum line and the control board

• Disconnect power to the appliance before starting; electrical shock risk
• Drain water and shut off water supply if needed to avoid spills when accessing the part
• Handle the vacuum hose and small fittings carefully; ensure vacuum line is seated and undamaged

This replacement drawer dispenser front restores the exterior face of the appliance dispenser drawer, improving fit and appearance while allowing the dispenser to open and close securely. Ideal when the original front is cracked, chipped, or discolored. What it does:

• Replaces a broken or worn dispenser drawer face so the drawer operates and seals correctly
• Keeps the dispenser drawer aligned and helps the dispenser open/close smoothly
• Prevents debris from entering the dispenser area and improves the appliance's finished look
• Useful when the original front is cracked, loose, or cosmetically damaged

• Disconnect power to the appliance before beginning any work
• Remove the dispenser drawer per the appliance service instructions to access the front panel
• Handle plastic parts carefully to avoid damage to clips and tabs during removal and installation
• Secure all clips; do not force or overtighten