Wcvh4800kww Parts

This drain plug seals the washer tub drain to prevent leaks and keep water inside the tub during normal operation. A simple replacement that restores a proper seal without replacing larger drain assemblies. What it does:

• Seals the drain opening to prevent water leakage from the tub
• Helps maintain proper water containment during fill and wash cycles
• Replaces a cracked, worn, or missing drain plug that causes pooling or dripping
• Works with the tub/drain assembly where a removable plug is used

• Remove power to the appliance before inspecting or replacing the plug
• Access may require removing the washer front panel or tub access panel depending on model
• Press or seat the plug firmly into the drain opening until fully seated; confirm a snug fit
• If you see corrosion, cracks, or damaged mounting surfaces, replace any affected components before returning the unit to service

This packing thermistor is a temperature sensor that mounts in the refrigerator/freezer door gasket to help the appliance monitor temperatures near the door seal for more accurate temperature control and efficient cooling. What it does:

• Senses temperature at the door gasket so the control board can adjust cooling and defrost cycles
• Helps prevent false warm readings caused by door-area drafts or melting frost
• Common symptoms when failing: inconsistent fridge/freezer temperatures, longer run cycles, or temperature-related error codes
• Works as the sensor input for system diagnostics and control logic

• One packing thermistor sensor

• Disconnect power to the appliance before replacing any parts
• Handle the sensor and its wiring gently to avoid damaging the lead or connector
• Route and secure the lead so it isn't pinched by the gasket when reinstalling the door

This hose guide secures and centers the dryer vent hose to help keep airflow aligned and reduce stress on the hose connection. It helps prevent the vent hose from becoming pinched or disconnected during normal use. What it does:

• Holds the vent/duct hose in place to maintain proper airflow alignment
• Reduces hose kinks and rubbing that can cause wear or air leaks
• Helps limit vibration and hose movement that can loosen the connection
• Addresses symptoms such as a shifting or sagging vent hose, rattling, or reduced vent clearance

• Disconnect power and move the appliance to access the vent area before servicing
• Remove any necessary rear/access panels to reach the hose connection
• Secure the guide in the original mounting location using existing fasteners or screws
• Inspect the vent hose and connection for damage; replace any worn ducting or seals as needed

A simple replacement wire tie that secures and organizes wiring harnesses inside the appliance to prevent rubbing, pinching, or contact with moving parts. Helps keep wiring routed neatly for safer operation and easier service. What it does:

• Bundles and secures loose wires and harnesses to prevent abrasion and chafing
• Keeps wiring away from motors, heaters, and moving components
• Reduces strain on connectors and terminals that can cause intermittent electrical issues
• Helps maintain factory routing for reliable appliance function

• Disconnect power before servicing the appliance
• Route wiring following factory harness paths; avoid contact with sharp edges and heat sources
• Tighten snugly but do not over-torque; trim excess tail with cutters
• Replace any brittle, melted, or damaged ties rather than reusing them

This wire tie secures appliance wiring and small harnesses to prevent chafing and movement. It keeps wires organized and reduces the risk of contact with sharp edges or moving parts for safer, quieter operation. What it does:

• Bundles and anchors wiring to prevent rubbing or snagging
• Helps stop wire vibration and rattles that can cause noise
• Keeps harnesses away from hot or moving components
• Supports reliable electrical connections by reducing strain on terminals

• Use appropriate-length ties and avoid over-tightening to prevent wire damage
• Trim excess tie tail flush and tuck away from moving parts
• Disconnect power to the appliance before working on internal wiring
• Replace any damaged insulation or connectors found while securing wires

This spring and lever assembly replaces a worn or broken actuator spring and latch lever to restore reliable door/latch movement and part engagement. It's a direct-fit component used in appliance latch mechanisms. What it does:

• Provides tension for the latch/lever so doors or panels close and stay engaged
• Restores smooth lever actuation when existing spring is weak or broken
• Prevents intermittent latch release or failure to stay closed
• Helps eliminate clicking, loose lever movement, or failure to engage

• Disconnect power to the appliance before servicing
• Basic hand tools required; access may require panel or door removal
• Handle small springs carefully to avoid loss or injury; wear safety glasses