Wd-13276Bd Parts

This small structural bracket supports the "leg" of an interior shelf or drawer assembly in compatible refrigerators. It helps keep shelves level and stable so bins slide smoothly and contents stay secure during everyday use. What it does:

• Supports the corner/leg of an interior shelf, cover, or drawer rail
• Helps maintain level alignment and prevents wobble or sagging
• Restores stability if the original piece is cracked, warped, or missing
• Common symptoms: shelf or drawer sags, binds, or rattles; poor fit/alignment

• 1 supporter leg

• Disconnect power and remove food from the affected area before starting
• Remove the shelf/drawer and note fastener locations or locking tabs
• Transfer any reusable screws/clips and seat the new supporter fully
• Reinstall components, ensuring the shelf/drawer sits level and moves freely

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

This leg support secures the adjustable leveling foot to the appliance's base. Replacing a damaged or stripped support restores a solid mounting point so you can properly level the unit and reduce rocking and vibration. What it does

• Provides the mounting point for the leveling leg; anchors to the base/frame
• Helps keep the appliance level and stable during operation
• Replace if cracked, bent, or the threads are stripped
• Common symptoms: rocking or unstable unit, excessive vibration/rattling, doors out of alignment, leveling foot won't hold adjustment

• 1 leg support

• Disconnect power; shut off water or gas supply if applicable
• With a helper, carefully tip and support the unit to access the base safely
• Remove fasteners, transfer or thread the existing leveling leg into the new support, and reinstall
• Set the appliance down and level it on all corners; verify stability

This stator assembly is the stationary motor coil that produces the magnetic field to drive the washer motor. Replaces a worn or damaged stator to restore magnetic coupling between the motor and rotor for normal drum movement. What it does:

• Generates the magnetic field the rotor uses to spin the drum
• Restores normal spin and agitation when a failed stator causes no-spin, weak spin, or humming
• Works with the washer's rotor/drive components as part of the motor assembly
• Handles the electrical and magnetic interface; must match motor/rotor configuration

• One stator assembly

• Disconnect power and water before servicing; use proper lockout procedures
• May require removal of the motor/rotor and housing to access the stator
• Inspect rotor magnets, bearings, and wiring for related damage while replacing

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

Replacement dispenser assembly that restores the refrigerator door's water/ice dispensing function and replaces a cracked or non-working dispenser chute or bezel. Helps stop leaks and returns reliable dispensing action. What it does:

• Routes water and/or ice from the dispenser to the cup and houses the dispenser actuator and mounting points.
• Replaces cracked, broken or worn dispenser chutes and bezels that cause leaks or catching.
• Restores dispenser lever/actuator responsiveness when the door switch or paddle is damaged.
• Can stop visible leaking from the dispenser area and improve user access to dispensed water or ice.

• Disconnect power and water supply before starting work to avoid shock or leaks.
• Remove refrigerator door trim or liner to access dispenser mounting screws and connectors.
• Handle sharp sheet-metal edges and beverage lines carefully; inspect and replace any damaged gaskets or tubing.

This accessory assembly is a factory replacement component that restores the original mounting/connection function in compatible LG appliances, helping eliminate loose fittings and restore secure operation. What it does

• Replaces a worn or damaged accessory assembly that secures or connects appliance components.
• Restores proper alignment and engagement of the affected assembly to reduce rattling or movement.
• Can help address symptoms such as loose parts, intermittent connection issues, or unusual noises originating near the assembly.
• Matches OEM fit and form to maintain original performance when installed correctly.

• Disconnect power (unplug or shut off breaker) before beginning any repair.
• Basic hand tools are typically required; follow the appliance service manual for removal and installation steps.
• Inspect surrounding components for wear or damage while replacing this assembly.

This accessory assembly is a factory-style replacement that restores missing or damaged accessory components so the appliance operates as intended. It provides the correct mounting and connection points for attached parts. What it does:

• Replaces a damaged or missing accessory assembly to restore proper accessory function
• Provides the OEM mounting points, connectors, and hardware interface for attached components
• Addresses symptoms such as loose or missing accessory parts, intermittent accessory connections, or improper fit
• Helps ensure accessories attach securely and align correctly with the appliance housing

• Disconnect power and water before starting service
• Follow the OEM instructions for removal and installation
• Basic hand tools are typically required; avoid forcing clips or connectors

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

This leveling leg assembly supports and stabilizes the appliance cabinet. It threads into the base to help level the unit on uneven floors, reducing vibration and movement for quieter, steadier operation.

• Provides height adjustment to level the appliance
• Helps reduce excessive vibration, walking, and rattling
• Supports proper door alignment and smooth operation
• Common fix when the unit rocks or is difficult to level

• Unplug the appliance and shut off water/gas before service
• Carefully tip or access the base to reach the leg location
• Thread the new leg by hand; adjust height with a wrench as needed
• The cabinet is level front-to-back and side-to-side

A Taptite screw used to fasten sheet metal and plastic appliance panels. This self-tapping fastener secures trim, brackets, and internal components for a reliable hold during normal use. What it does:

• Creates its own threads in metal/plastic for a tight, vibration-resistant connection
• Commonly used to secure control panels, trim pieces, and mounting brackets
• Helps stop rattles and keeps panels aligned when properly installed
• Compatible with repair and maintenance tasks where original fasteners are required

• Use the correct sized driver and steady pressure to avoid stripping the head
• Start straight and drive slowly until snug; do not over-tighten
• Wear eye protection when working with small fasteners and metal panels
• Replace any damaged or stripped screws with the exact OEM fastener

This inlet valve assembly controls water flow into the appliance so it fills only when needed and helps prevent unwanted leaks. It replaces a worn or failed inlet valve to restore normal fill operation. What it does:

• Opens and closes to allow water into the unit during fill cycles
• Stops water flow when fill is complete to prevent overfilling
• Common symptom: no water or slow/no fill
• Common symptom: continuous filling or overflow risk
• Common symptom: water leaking from valve area

• Disconnect electrical power and shut off the water supply before starting
• Drain remaining water from hoses and lines to avoid spills
• Replace with the exact part number and secure all fittings; use hand tools and avoid overtightening

This drain pump assembly replaces a failed washer drain pump to restore normal water removal. It helps clear standing water so cycles can finish and reduces leaks or overheating risks from trapped water. What it does:

• Pumps water from the tub to the household drain during drain/spin cycles.
• Common failure signs: washer won't drain, water left in tub after cycle, or cycle stalls.
• A leaking pump can allow water to escape under the machine or trigger error codes.

• Disconnect power and shut off water before starting any repair.
• Drain remaining water from the tub and disconnect hoses carefully to avoid spills.
• Match and reconnect electrical connectors exactly; secure hose clamps and check for leaks.
• After installation, run a short drain/spin cycle and inspect for proper operation and leaks.