Wd3274rhd Parts

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

This hose connector joins washer plumbing lines to the appliance so water flows securely where it should. It replaces a worn or damaged connector to help stop leaks and restore proper water routing. What it does:

• Connects a washer hose to the appliance plumbing to maintain a watertight path
• Helps prevent leaks caused by cracked or split connectors
• Restores reliable water flow when a failed connector is the source of drips or poor sealing
• Works with existing hose clamps and fittings when in good condition

• Disconnect power and shut off the water supply before servicing
• Drain residual water from hoses to avoid spills during replacement
• Inspect hose ends and clamps; replace clamps if corroded or damaged

This replacement clamp secures flexible hoses and tubing to fittings to help prevent leaks and keep connections stable. It's a small but essential part for reliable water and drain line performance. What it does:

• Holds hoses or tubes firmly to barbs, fittings, or posts to prevent disconnection
• Helps reduce leaks and water seepage at hose connections
• Minimizes rattling or vibration from loose tubing
• Supports proper routing of lines to avoid kinks or wear

• Disconnect power and water supply before starting any repair
• Use appropriate hand tools (pliers or a screwdriver, depending on clamp type) and avoid over-tightening
• Inspect nearby hoses and fittings for wear and replace if damaged

This part may be black or gray in color.