Wdf330pah-Do Parts

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This feed tube assembly channels water where it belongs in the appliance, restoring proper flow and preventing misdirected or leaking water. Designed as a two-level, green plastic tube for direct replacement of the original part. What it does:

• Routes water from the inlet to the correct internal channels to support normal appliance operation
• Helps prevent leaks or puddling caused by cracked or clogged feed tubes
• Replaces damaged, warped, or discolored tubing that can interrupt water flow
• Can resolve symptoms like water dribbling inside the cabinet, poor dispensing, or intermittent water flow

• Disconnect power and water supply before starting any repair
• Inspect mating seals and clips; replace if damaged to ensure a watertight fit
• Handle plastic fittings carefully to avoid cracking; tighten connections per OEM guidance

The Wire Harness is an OEM component specifically designed for Whirlpool dishwasher models. Found running across the inner tub cavity and control compartments, the wire harness routes electrical connections between the control panel, pump, heater element, and other critical components. 

Composed of flame-retardant plenum-rated cabling with silicon jacket coating, the harness features carefully positioned bundles routed through grommet-sealed anchors. Precise terminal connections deliver consistent voltage levels to components. 

Causes of a bad wire harness include degraded insulation from prolonged high-temperature and moisture exposure and weakening internal cabling. Cracks or abrasions exposing vulnerable wiring over time are also possible causes.

Symptoms of a bad wire harness include:  

• Faulty or non-responsive controls
• Unexpected error codes 
• Intermittent component operation

Compatible with additional dishwasher brands including KitchenAid, Jenn-Air, and select Kenmore models.

This inner door panel replaces a cracked or damaged inner door to restore the appliance's interior finish and provide the correct mounting surface for door hardware. It matches the OEM shape for a factory fit and appearance. What it does:

• Replaces a damaged or dented inner door panel to improve appearance and function
• Provides the correct mounting surfaces for trim, handles, and internal components
• Helps protect internal parts from moisture and debris when the door is closed
• Restores proper fit and alignment with the outer door assembly

• One inner door panel

• Disconnect power (and water supply for appliances with water connections) before beginning work
• Handle edges and any attached glass or trim carefully—wear gloves to protect hands
• Use original fasteners where possible; keep screws and clips organized during removal
• After installation, check door alignment and operation before returning the appliance to service

This is an electrical wire-harness connector used to join wiring in the appliance. It restores a secure electrical connection so controls and components receive proper power and signaling. What it does:

• Provides a secure mating point between wiring harnesses or between a harness and a component
• Maintains proper electrical contact to prevent intermittent power or signal loss
• Commonly used where a detachable electrical connection is needed for service or assembly
• Can help address symptoms like intermittent operation, components not powering on, or visible damaged/loose plug ends

• Disconnect power to the appliance before inspecting or replacing any electrical connector
• Verify connector orientation and full engagement; bent terminals may need replacement
• Compare the replacement to the original to ensure terminal count, shape and locking feature match
• If wiring insulation or terminals are damaged, replace the harness

Color: Black

The Console is an OEM part for Whirlpool dishwashers. It forms the outer control panel and houses the interface used to operate cycle selections and model settings. The console allows for convenient cycle programming and monitoring through illuminated buttons and LED displays. It is constructed from moisture-resistant plastics built to withstand the wet environment inside the dishwasher.

Causes of a bad console can include cracked or broken buttons from repeated use, faulty circuit boards affecting displays and functions, or openings that compromise the splash resistance.

Symptoms of a bad console include:

• Buttons or displays that are unresponsive when pressed
• Inability to select desired wash cycles
• Erratic indicator lights during operation
• Water intrusion causing internal component damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: White
 

Color: Bisque