Wed 4800Xq1 Parts

This genuine wire harness connects the appliance's control components and restores reliable electrical routing for proper operation. It replaces a damaged or frayed harness to help eliminate intermittent power or non-responsive controls. What it does:

• Routes power and signals between the control board and components so the appliance can operate correctly
• Replaces worn, burned, or damaged wiring that can cause intermittent operation or failure to start
• Restores proper connections when controls, lights, or motors behave unpredictably
• Reduces the risk of shorted or exposed wires that interrupt appliance function

• Disconnect power (and water, if applicable) before starting any repair
• Compare the harness to the old part to ensure connector types and lengths before installing
• Route wires away from sharp edges and moving parts; secure with existing clips or ties
• If you see burned connectors or damaged terminals on mating parts, replace or repair those components as well

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

This replacement pad cushions contact between components to reduce noise, vibration, and surface wear. Use it to restore stable, quieter operation and protect mating surfaces from damage. What it does:

• Cushions contact points to minimize rattling and vibration
• Helps prevent surface scuffs or wear where parts meet
• Can reduce squeaks and intermittent noise caused by loose contacts
• Restores proper component seating for more consistent operation

• Disconnect power before accessing internal components
• Remove the old pad and press the new pad into the same location until fully seated
• Use only the specified pad for the designated mounting point; do not modify

This rear panel replaces the dryer's back bulkhead to restore the appliance's structural enclosure and help protect internal components from dust and debris. It provides a clean mounting surface for internal parts and improves cabinet integrity. What it does:

• Replaces a damaged, dented, or corroded rear cabinet panel
• Protects internal wiring, ducts, and components from external debris
• Restores proper mounting surfaces for internal assemblies and fasteners
• Helps maintain correct airflow paths by sealing the dryer cabinet

• One rear panel/back bulkhead

• Disconnect power (and gas if applicable) before beginning any repair
• Installation typically requires removing the dryer cabinet and several fasteners; keep hardware for reuse unless damaged
• Inspect and replace any worn gaskets, seals, or mounting clips while cabinet is open

This is a drum assembly intended for use with dryers. This part can be found inside the dryer and is responsible for holding clothing while a cycle is running. It holds wet laundry while loading the appliance. Over time and with use, the drum assembly can start to wear out. This can cause the dryer to squeal, start and stop during a cycle, make buzzing noises, or seize up.If the drum assembly is damaged, it will need to be replaced. Make sure to have basic tools and a pair of work gloves ready. The dryer should be turned off and unplugged from the wall. Raise the top panel, remove the front panel, and then remove the drum. The drum support roller should be taken out and installed on the new drum. Reinstall with the new component and reassemble all parts before use.The drum assembly is made to be used with dryers and washer/dryer combos from Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold on an individual basis.

This wire harness is the factory-style electrical assembly that connects and routes power and signal wiring between an appliance's components, restoring reliable electrical connections and control communication. What it does:

• Provides factory-routing for power and signal wires between control, motors, switches, and sensors
• Restores lost or intermittent electrical connections that can cause no-start, no-heat, or erratic operation
• Replaces damaged, frayed, or corroded wiring to reduce short or open-circuit failures
• Maintains correct connector fit and wire length to prevent strain and interference

• One complete wire harness assembly as shown

• Disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Compare connectors and wire routing to the original harness before installation
• Use proper strain reliefs and routing; avoid sharp edges and heat sources when reinstalling

Color: White.

This replacement control knob restores safe, reliable control of a range or oven burner. It provides a secure grip and clear pointer so you can set heat levels accurately and replace a missing or damaged knob quickly. What it does

• Replaces a worn, cracked, or missing control knob so the appliance can be operated normally
• Provides a clear pointer for setting temperature or burner power levels
• Allows the shaft to be turned smoothly when selecting settings
• Helps prevent accidental changes caused by a damaged knob

• One control knob

• Disconnect power to the appliance (or shut off gas) before servicing
• Most knobs pull straight off the control shaft; inspect shaft for damage before installing
• Align the knob's socket and press on until fully seated; test operation after restoring power
• If the shaft or underlying control is damaged, replace the damaged component rather than just the knob